• Tribology and Lubricants
• /
• 제12권2호
• /
• pp.55-64
• /
• 1996

Frictional characteristics with the change of loading method and normal stiffness at dry sliding surfaces were experimentally and theoretically evaluated in this study. For the study, a ball-on-disk typed test rig was built and implemented, which allowed a proper selection of loading mechanism and normal stiffness of the test rig. Loading method were varied from dead weight to pneumatic cylinder and spring loading, and the normal stiffness was varied by a spring of different stiffness. Test results showed that frictional characteristics at various loading methods were different even though the operating variables were the same. Discrepancy in the frictional characteristics, such as coefficient of friction and fluctuation in the normal load, were explained by the change in dynamic parameters of the test rigs. Results also showed that coefficient of friction, which defines as a ratio of frictional force divided a normal load, could be differently evaluated in the calculation when fluctuation in the normal load was significant.

• 한국자동차공학회논문집
• /
• 제7권7호
• /
• pp.268-277
• /
• 1999

In order to make an advanced dry-friction engineering material, wax-impregnated nylons were synthesized by anionic polymerization of $\varepsilon$-caprolactam in the presence of apraffin wax. DNX-125S, which has lowest melting point among four different kinds of waxs investigated, showed excellent miscibiility with $\varepsilon$-carprolactam and no effect on the polymerization reaction. Five different kinds of wax-impregnated nylons from of DNW-125S content 0% to 8% were synthesized and tested. Among the samples, wax-free nylon has the highest yield and tensile strength and hardness, while the specimen with2% wax has the largest elongationi and energy absorption to break. The wax-impregnated nylon with a wax content 6% showdd the smallest friction coefficient under slow sliding speed and low load. Bus as the sliding speeds were increased to high, thespcieimen with 8% wax has better friction property.

• 한국윤활학회:학술대회논문집
• /
• 한국윤활학회 2000년도 제32회 추계학술대회 정기총회
• /
• pp.59-66
• /
• 2000

An experimental study on the effect of silver particles on the sliding behavior of bearing steels was performed by using a ball-on-disk tribometer. Tests were carried out in ambient air, dry and vacuum. Disks of AISI 52100 were silver-coaled by a thermal evaporation method, and the effects of silver particle transfer on friction were firstly analyzed. In order to understand further the mechanism of silver particles transfer and its effect on friction and wear, pre-compressed silver particles were artificially introduced into the friction interface and the results were compared to those of silver-coated specimens. Results showed that the introduced silver particles produced transfer layers and resulted in low friction. It also showed that this low friction is closely related to the characteristic behavior of transfer layers. Shakedown and rachetting occurred at the friction interface and affected the friction and wear.

• 한국윤활학회:학술대회논문집
• /
• 한국윤활학회 2003년도 학술대회지
• /
• pp.118-126
• /
• 2003

In the present study, the residual stresses can have a significant on the life of structural engineering components. Residual stresses are created by the surface treatment such as shot peening or deep rolling. The objective of this experimental investigation is to study the influence of friction and wear characteristics due to residual stress under dry sliding condition. Friction and wear data were obtained with a specially designed tribometer. Test specimens were made of SUP9(leaf spring material) after they were created residual stress by shot peening treatment. Residual stress profiles were measured at surface by means of the X-ray diffraction. Sliding tests were carried out different contact pressure and same sliding velocity 0.035m/s(50rpm). Leaf spring assembly test used to strain gauge sticked on leaf spring specimen in order to measure interleaf friction of leaf spring. Therefore, we were obtained hysteresis curve. As the residual stresses of surfaces increased, coefficient of friction and wear volume are decreased, but the residual stresses of surfaces are high, and consequently wear volume do not decreased. Coefficient of friction obtained from leaf spring assembly test is lower than that obtained from sliding test. From the results, structural engineering components reduce coefficient of friction and resistant wear in order to have residual stresses themselves.

• 한국윤활학회:학술대회논문집
• /
• 한국윤활학회 2000년도 제31회 춘계학술대회
• /
• pp.251-257
• /
• 2000

A numerical simulation of the temperature rise for sliding surface in dry contact is based on Jaeger's formula combined with a calculated heat input. A gear tooth temperature analysis was performed. The pressure distribution has the Hertzian pressure distribution on the heat source. The heat partition factor is calculated along line of action. A Temperature distribution of tooth surface is calculated about before and after profile modification. A Temperature of addendum and deddendum in modified gear have reduced.

• 한국윤활학회:학술대회논문집
• /
• 한국윤활학회 2002년도 proceedings of the second asia international conference on tribology
• /
• pp.137-138
• /
• 2002

The benefits of using DLC coatings on steel in dry sliding are well known. The present study has investigated the effects of using the same materials but in a boundary lubricated environment. Tribological tests were performed using a load-scanning device and a lubricant with an extreme-pressure (EP) additive. XPS and grazing incidence XRD are used for chemical analysis. The chemical composition of the resulting tribofilm is correlated to different friction behaviors and contact loads, and indicates that high loads are beneficial for formation of low friction tribofilm.

• Journal of Advanced Marine Engineering and Technology
• /
• 제25권2호
• /
• pp.331-337
• /
• 2001

A numerical simulation of the temperature rise for sliding surface in dry contact is based on Jaegers formula combined with a calculated heat input. A gear tooth temperature analysis was performed. The pressure distribution has the Hertzian pressure distribution on the heat source. The heat partition factor is calculated along ling of action. A Temperature distribution of tooth surface is calculated about before and after profile modification. A Temperature of addendum and deddendum in modified gear have reduced.

• Tribology and Lubricants
• /
• 제12권3호
• /
• pp.26-32
• /
• 1996

오랜 역사에 걸쳐 연구자들은, 마찰력은 주로 접착에 의한 것으로 믿어 왔으며, 이러한 주장은 실험적으로 증명되지 못했다. 한편, 미끄럼 두 표면 사이의 건식 마찰력은 두 표면 사이의 기계적인 상호작용에 의한 것으로 알려져 있다. 이 연구에서는 두 표면 사이의 기계적 상호작용을 제거함으로써 마찰계수를 감소시키는 방법을 제시하였다. 매끄러운 경한 표면에 얇은 elastomer층을 입힌 비윤활 최소 마찰계수에 대한 본 실험결과는 앞으로 정밀기계부품의 충격을 받는 부위에 응용할 수 있을 것으로 기대된다.

• 대한용접접합학회:학술대회논문집
• /
• 대한용접접합학회 2001년도 춘계학술발표대회 개요집
• /
• pp.245-247
• /
• 2001

In this study, the effects of dilution on the wear behavior of PTAW (Plasma Transferred Arc Welding) Inconel 625, Inconel 718 and Stellite 6 overlays on Nimonic 80A were investigated. Inorder to evaluate the wear performance, two-body and three-body abrasive wear test, and dry sliding wear test were performed. According to wear tests, the wear rate of deposit with dilution 30% was higher than that of dilution 10% by 10%, and it was also found the plastic deformation near worn surface.

• 한국윤활학회:학술대회논문집
• /
• 한국윤활학회 1998년도 제28회 추계학술대회
• /
• pp.38-48
• /
• 1998

To apply the high chromium white cast irons for sliding parts of construction equipments, the wear characteristics of these alloys which have three kinds of microstructure(hypoeutectic, near-eutectic, hypereutectic) were investigated by dry sand/rubber wheel tester. Also, the effect of heat treatment was investigated for the same alloys. As result of the test, heat treatment have no effect on the wear characteristics. And, hypereutectic composition alloy has the highest wear resistance against SiO$_2$. Also after test, cracking was observed in eutectic and primary carbides of all materials tested. This phenomenon was important factor in the wear resistance.