• Geotechnical Engineering
• /
• v.24 no.6
• /
• pp.41-47
• /
• 2008

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.21 no.9
• /
• pp.569-574
• /
• 2020

A floating dock is the main facility for launching ships. In the early 2000s, ship-launching technology using floating docks was developed in Korea. Therefore, the opportunity to participate in new construction projects without investment in dry docks has expanded. In this paper, a basic calculation for the safe mooring of a floating dock was performed, and a mooring system was designed based on this. This study was conducted considering the typhoon situation, which is the most serious environmental requirements of Daebul Pier, a site to be installed and operated, for a floating dock. The design load was calculated by wind load, tidal load, and wave-induced load in accordance with the internationally accepted standards. After performing the initial arrangement of the mooring line of the floating dock using the existing mooring facilities of Daebul Pier, the minimum breaking load for each mooring line was calculated for the given load. Based on the calculation, the mooring arrangement was modified to minimize the breaking load, and a final specification of each mooring line was selected.

• Journal of Animal Science and Technology
• /
• v.57 no.11
• /
• pp.34.1-34.5
• /
• 2015

Himalayan dock (Rumex nepalensis) was evaluated for forage value and antinutrients under three, five and seven weeks cutting intervals in the temperate environment. Dry matter (DM) content was measured for each cutting interval. Forage quality parameters such as Crude Protein (CP), Acid Detergent fiber (ADF), Neutral Detergent Fiber (NDF), Calcium (Ca) and Phosphorus (P) were analyzed. Plants with seven weeks cutting interval gave higher DM yield. CP and P content were significantly higher for three weeks cutting intervals. Average CP contents were 31.38 %, 30.73 % and 27.32 % and average P content 0.58 %, 0.52 % and 0.51 % for three, five and seven weeks cutting intervals, respectively. Ca content did not differ significantly between cutting intervals. The average Ca content were 0.91 %, 0.90 % and 90 %, for three, five and seven weeks cutting intervals, respectively. Tannin and mimosine contents were not significantly different between cutting intervals. Average tannin contents were 1.32 %, 1.27 % and 1.26 % and mimosine 0.38 %, 0.30 % and 0.28 % for three, five and seven weeks cutting intervals, respectively. The study concluded that R. nepalensis could be a potential source of protein for livestock. The study also suggests seven weeks harvesting interval to provide plants with high dry matter yield, high forage quality and very low levels of anti-nutrients.

• Journal of Advanced Research in Ocean Engineering
• /
• v.1 no.3
• /
• pp.148-156
• /
• 2015

Deck plates of ships or offshore structures would make out-of-plane distortion for their thin thickness. These distortions are usually straightened by thermal straightening such as flame heating method. After thermal straightening, the blocks are lifted and moved by cranes to assemble it at dry-dock stage. After this lifting process, out-of-plane deformation again happens frequently. And then, they continuously cause quality and accuracy problems in the final dry-dock process. So, it takes more time for repair and correction working. According to preceding research, the lifting process by cranes would offset the effect on thermal straightening. The target of this study is to develop a methodology analyzing the remaining efficiency of thermal straightening after block lifting. The development was based on the assumption of yield state at straightening region. Therefore the remaining efficiency was obtained by different stiffness slope while lifting & relieving. The efficiency formula was designed using inherent strain, and we made a table of zero-efficiency by cooling speed and class rule's steels. As a result, if the stress orthogonal to straightened line is calculated during lifting analysis by FEA, the efficiency can be obtained linearly to the values in the table. Finally, even optimized carling position can be designed by considering the regional data from series project and welding region on deck.

• Journal of Ocean Engineering and Technology
• /
• v.22 no.4
• /
• pp.78-83
• /
• 2008

In recent years, small boats used for marine leisure have been steadily increasing because of the increase in national income and the desire for marine leisure. But the repair of such small boats in dry dock has pointed out many faults in small FRP-shipbuilding in terms if workspace and manpower. Lifting a boat from the water to land is done with a crane or by hand using a sling around the bottom of the boat. But dry dock work is limited by the scale of the boat, which corresponds to the crane capacity, with carelessness making it possible to capsize a boat and endanger life. The purpose of this study was the development of a marine docking system that would improve economical efficiency and safety, for which we carried out concept design, model tests, structural analysis, etc.

• Special Issue of the Society of Naval Architects of Korea
• /
• 2008.09a
• /
• pp.10-15
• /
• 2008

The proper docking block arrangement, loading condition and structural reinforcement are required to ensure structural safety of ship, when she is in re-docking and launching for inspection or repair. The large reaction force due to narrow bottom tangent area, heavy weight and ballast loading are occurred at aft body and fore body of ship. Especially, in case of LNGC, the strength evaluation is necessary for cargo hold areas including mid-body because tank hydro test is performed in dry-dock. The analysis results and experiences to confirm structural safety for docking of conventional LNGC$(138K{\sim}151.7K)$ are introduced in this paper.

• Computational Structural Engineering
• /
• v.22 no.4
• /
• pp.89-94
• /
• 2009

최근에 선박의 도킹해석은 3차원 전선 구조 해석을 통해 수행되어 왔으나 도킹해석 모델을 구성하는데 많은 시간과 노력이 필요하였다. 전선구조해석 모벨을 만들기 위해 필요한 선박구조 도면이 완성되기 전인 초기 설계단계에서 도킹시 반목배치를 조기에 확정하고, 구조 안정성을 확보하기 위한 노력이 요구되어 왔기 때문에 간이화된 도킹 해석 프로그램을 개발하게 되었다. 2차원 격자구조를 이용한 도킹해석기법을 통해 얻은 반목에서의 지지력이 3차원 전선해석모델을 사용하여 얻은 반목에서의 반력 결과와 비교해 타당한 결과를 보여 주고 있음을 확인하였다. 간이화된 도킹용 해석 프로그램을 개발하였으며, 다음과 같은 기능을 갖추어 사용자가 쉽게 격자 구조 모델을 생생하고 해석을 수행할 수 있도록 구성하였다. 향후 각 요소의 단면 특성치를 자동으로 산정하는 기능이 추가되어야 한다. 그리고 부유식 도크(Floating dock)에서의 도킹해석은 본 개발의 대상이 된 건식 도크(Dry dock)에서의 경우와 다른 고려사항이 추가되어야 하기 때문에 향후 추가적인 연구와 개발을 통해 새로운 기능으로 포함될 것이다.

• Journal of the Korean Professional Engineers Association
• /
• v.43 no.2
• /
• pp.30-33
• /
• 2010

Immersed tunnel had been a rather new term in Korea before Busan-Geoje fixed link project was started and became known through the media. Although Korean is unfamiliar with the immersed tunnel, this construction method has a long history in the world. Busan-Geoje Fixed Link immersed tunnel consist of 18 elements and each element is approximately 180m long. These tunnel elements are prefabricated of reinforced concrete in a temporary dry dock and are towed to the site and lowered into final position in a dredged trench and are placed on a screeded gravel bed directly without temporary support.

• Proceedings of the Korean Institute of Navigation and Port Research Conference
• /
• 2021.11a
• /
• pp.160-161
• /
• 2021

추진동력원인 모터의 동력을 외부 수중에 있는 프로펠러에 전달하는데 있어서 해수 유입을 막은 수밀화 장치를 해야하고 매년 정기적으로 또는 손상시 본 부품을 교체하는데 많은 비용을 들어 선박을 Dry dock나 Slip Way에 상가해서 교체하는 단점을 가지고 있다. 크루선에 장착된 Azipod System은 조정성이 우수해 자력 이접안이 가능하다. K-Azipod형 무접촉 동력전달 장치는 Azipod 및 일반 선박에도 적용이 가능한 제품이다.

• IE interfaces
• /
• v.24 no.1
• /
• pp.78-86
• /
• 2011

To mitigate space restriction and to raise productivity, some shipbuilding companies use floating-docks on the sea instead of dry-docks on the land. In that case, a floating-crane that can lift very heavy objects (up to 3,600 tons) is used to handle the blocks which are the basic units in shipbuilding processes, and so, very large blocks (these are called the mega-blocks) can be used to build a ship. But, because these mega-blocks can be made only in the area near the floating-dock and beside the sea, the space is very important resource for the process. Therefore, our problem is to make an efficient spatial schedule for the mega-block assembly yard. First of all, we formulate this situation into a mathematical model and find optimal solution for a small problem using a commercial optimization software. But, the software could not give optimal solutions for practical sized problems in a reasonable time, and so we propose a GA-based heuristic algorithm. Through a numerical experiment, finally, we show that the spatial scheduling algorithm can provide a very good performance.