• 마이크로전자및패키징학회지
• /
• 제15권4호
• /
• pp.77-86
• /
• 2008

본 연구에서는 유연솔더인 63Sn37Pb와 무연 솔더인 95.5Sn4.0Ag0.5Cu와 97Sn2.5Ag0.5Cu BGA(Ball Grid Array) 패키지를 인쇄회로기판(Printed Circuit Board, PCB)에 위치에 따라 장착하고 보드레벨의 낙하시험(Board Level Drop Test)을 실시하여 충격에 대한 유 무연 솔더의 특성을 분석하였고 4점굽힘시험(board Level 4-point Bending Test)을 실시하여 굽힘에 대한 솔더볼의 기계적 저항특성을 분석하였다. 또한 유한요소법(Finite Element Modeling, FEM)을 이용해 낙하시험과 4점굽힘시험에서 솔더 조인트에 미치는 응력과 변형률을 해석하였으며, 시험 설계 시에 솔더 조인트의 응력변화에 영향을 미칠 수 있는 변수를 고려하여 해석하고 결과를 비교 분석하였다. 낙하시험과 4점굽힘시험에서 모두 무연솔더는 유연솔더보다 2배 이상 높은 신뢰성을 보였으며, PCB의 중앙에 위치한 패키지는 외각에 위치한 패키지 보다 매우 낮은 신뢰성을 보였다. 유한요소법을 통해 해석한 결과 최외각 솔더에서 가장 큰 응력이 발생하였고, 솔더의 조성과, 시험설계변수에 의해 응력의 발생 정도가 다름을 나타내었다.

• 한국가스학회지
• /
• 제25권5호
• /
• pp.37-51
• /
• 2021

가스 레귤레이터에 동일한 유량을 공급할 때 발생하는 압력 강하 현상을 분석하였다. 레귤레이터는 특정 범주의 환경에서 일정한 압력을 토출하기 위해 피스톤 상/하부에 작용하는 힘과 스프링 장력 간의 상호 작용으로 피스톤의 위치를 이동시켜 압력을 유지하는 특성이 있다. 레귤레이터 내부의 유체의 체적이 변화함에 따른 레귤레이터의 유동특성과 압력제어과정을 수치해석기법을 통해 분석하였다. 피스톤과 피스톤 시트 사이의 간격이 감소함에 따라 압력 강하가 증가하고 유속이 증가하였다. 압력-유량시험과 동일한 조건(입구압력 3MPa, 출구압력 0.8MPa, 유량 70kg/h)에서 피스톤이 0.12mm에 위치함을 수치해석을 통해 검증하였다.

• 항공우주시스템공학회지
• /
• 제7권1호
• /
• pp.19-25
• /
• 2013

Smoothed Particle Hydrodynamics(SPH) method uses a grid of historical analysis and is not Lagrangian particles using the grid method. The Navier-Stokes equations were used to solve the viscous flow of the non-compressed. In this study, the numerical analysis of the three-dimensional Coin Drop Simulation using SPH method was performed, and the analysis results are compared with experimental results, and a similar behavior can be seen. The commercial program used was Abaqus/Explicit. SPH method to reduce the error by comparing the existing flow analysis or interpretation of the continuing research is needed in the future. That will enable real-time analysis of material obtained as a result of these numerical simulations similar to the actual flow phenomena, depending on the development of computer graphics technology to show visually. As a result, this method can be applied to the analysis fluid - structure interaction problems in a variety of fields.

• 한국기계가공학회지
• /
• 제16권1호
• /
• pp.24-29
• /
• 2017

There is a need for explosion experiments for explosion-related research. However, there are many restrictions in performing an actual experiment. Therefore, in this paper, an alternative method of overcoming the constraints of an explosion experiment has been conducted using a passenger behavior analysis program called MADYMO to assess and analyze the human body injury due to explosion load. To increase the reliability of the analysis, a drop test has been conducted with the analysis. We provide a new framework for performing the analysis. In future, we will further develop our research with the goal of reducing the opportunity cost for the study of the human body injury.

• 한국운동역학회지
• /
• 제31권3호
• /
• pp.168-175
• /
• 2021

Objective: To investigate the static and dynamic analysis of ankle joint complex between subjects with chronic ankle instability (CAI) and healthy controls. Method: A total of 38 subjects and CAI group (N=19) and healthy control (N=19) participated in this first study. Variables that were measured in this study were as follows: 1) Subtalar joint axis inclination and deviation 2) Rearfoot angle 3) Navicular drop test 4) Heel alignment view in alignment analysis. Intra Correlation Coefficient (ICC) is used for reliability. A secondary 17 subjects are recruited including 9 of CAI and healthy for gait analysis between group. Lower extremity sagittal, frontal, and transverse kinematics were measured. All data were analyzed to ensemble curve analysis. Results: 1) There were statistically significant differences in standing rearfoot, navicular drop, heel alignment view, subtalar joint (STJ) inclination and deviation. 2) Only in sagittal, meaningful difference is showed during walking in gait analysis. Conclusion: Morphological problem can affect ankle sprain in aspect of structure with no relation to compensation of neuromuscular.

• 한국산업융합학회 논문집
• /
• 제25권4_2호
• /
• pp.541-547
• /
• 2022

Before making a prototype, we predicted the inlet/outlet differential pressure and flow coefficient, which are the most basic design data for the valve through the design and numerical analysis of the trim, which is the most important in the localization development of the 1500Ib high differential pressure control valve used for boiler feed water. As a result, the design value and the analysis value were found to be about 98% similar. The flow field within the fluid velocity of 23m/s to prevent cavitation was also found. The result of the numerical analysis on thermal stress due to the characteristics of valves exposed to high temperatures showed that it was found to be about 18% less than the allowable stress of the bolt fixing the trim. When all loads such as pressure, self-weight, and vibration are applied, however, it is judged to go beyond the currently calculated thermal stress, exceeding the allowable stress.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2002년도 하계학술대회 논문집 B
• /
• pp.1114-1116
• /
• 2002

The characteristics of voltage drop and THD for parallel operating 11 PCRs (Phase Controlled Rectifiers) are analysed. The PCRs are used to drive high current (1.6 kA ${\sim}$ 3.7 kADC) electromagnetic coils for electromagnets. All the PCRs operate simultaneously in pulsed mode, and the pulse shot occurs every 150 seconds. During the pulse operation the PCR output current ramps up for 4 seconds, and then keeps flat top state for 2 seconds, and finally ramps down for 4 seconds. For the flat top mode a severe voltage drop and distortion appear in the power system because transformers for the PCRs are designed considering pulsed mode operation. It is expected that the analysis method can be applied to improve the system performance including power factor and design of high power pulsed mode operating power supply systems.

• 한국철도학회:학술대회논문집
• /
• 한국철도학회 2011년도 정기총회 및 추계학술대회 논문집
• /
• pp.1659-1663
• /
• 2011

Precast concrete slab track is a track structure to be installed by transporting and assembling precast concrete slabs manufactured at the factory. This method can improve concrete quality, provide easy maintenance and reduce construction time, compared with in-situ concrete track. However, the concrete slabs being continuously connected in longitudinal direction, due to the temperature change between summer and winter, the openings at slab joints have occurred. Thus, in this study, to identify the cause of this opening of slab joint, the joint opening caused by temperature drop in the longitudinally continuous precast concrete slab track has been predicted using three-dimensional finite element analysis, and compared with field measurements. Based on the proven model, the slab joint opening, and the stress pattern of concrete slab and steel reinforcement according to concrete slab-base friction properties, concrete-reinforcement bond properties, and prestressing were analyzed.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2004년도 추계학술대회
• /
• pp.1424-1429
• /
• 2004

To seek the fan operating point on a cooling system with fans, it is very important to determine the system impedance and it has been usually examined with the fan tester(wind tunnel) based on ASHRAE standard and AMCA standard. This leads to a large investment in time and cost, because it could not be executed until the system is made actually. Therefore it is necessary to predict the system impedance curve through numerical analysis so that we could reduce the measurement effort. This paper presents how the system impedance curve (pressure drop curve) is computed by CFD in substitute for experiment. In reverse order to the experimental principle of the fan tester, pressure difference was adopted first as inlet and outlet boundary conditions of the system and then flow rate was calculated.

• 한국정밀공학회지
• /
• 제24권11호
• /
• pp.101-107
• /
• 2007

Jettability analysis using one-dimensional(1D) lumped parameter model has been investigated to design the industrial inkjet head with proper drop velocity and drop volume. By simplifying the inkjet head system into an equivalent electrical circuit, lumped model has been developed. Performance of the lumped model is verified by the comparison between measured results of droplet velocity and ejection volume and predicted value. Also, the jetting performance of an inkjet head is characterized by varying the design parameter and driving condition. As a result, simulation results shows good agreement with the experimentally measured value. The developed lumped model enables to easily understand the effect of dimension change and predict the jetting performance.