• Journal of ILASS-Korea
• /
• v.22 no.2
• /
• pp.47-54
• /
• 2017

$CO_2$ emission regulation will be prescribed and main issue in automotive industry. Mostly, vehicle's fuel efficiency deeply related to $CO_2$ emission is regulated by qualified driving test cycle by using chassis dynamometer and exhaust gas analyser. But, real driving fuel consumption rate depends so much on the individual usage profile and where it is being driven: city traffic, road conditions. In this study, vehicle model of fuel consumption rate for ICEV and PHEV was developed through co-simulation with CRUISE model and Simulink based on driving control model. The simulation results of fuel consumption rate were analysed with on-road vehicle data and compared with its official level.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.61 no.7
• /
• pp.974-981
• /
• 2012

This paper studied about the measurement method of the instantaneous dynamic load characteristics. this experimental study, we derived the instantaneous washing load characteristics and inertial moment characteristics according to the amount of laundry and water level. Also, this studied about the dynamic driving characteristics simulation method for the prediction of washing performance based on this load characteristics analysis. For this study, the design parameters of the driving motor are obtained by FEM analysis and the experiment. By using theses motor parameters and load characteristics, the instantaneous driving characteristics simulation is accomplished and it is verified with the experimental result of various driving conditions. The results of this paper would be very useful to the prediction of washing mode operation characteristics, and it can be also utilized to the washer motor control algorithm design for the washing performance improvement.

• Journal of Korea Society of Digital Industry and Information Management
• /
• v.17 no.4
• /
• pp.31-42
• /
• 2021

In the modern era, radio wave analysis is necessary for various fields of engineering, and interpretation of this is also indispensable. Self-driving cars need multiple different electronic components, and thus accurate and fast electromagnetic simulator for this kind of complex radio environment is required for self-driving simulations. Accordingly, the demand for self-driving simulators as well as existing electromagnetic analysis software has increased. This paper briefly describes the characteristics of numerical analysis techniques for electromagnetic analysis, self-driving simulation software, and conventional electromagnetic simulation software and also summarizes the characteristics of each software. Finally, the verification of the result from in-house code compared to HFSS is demonstrated.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.10 no.1
• /
• pp.195-202
• /
• 2002

By using modeling and simulation. today's design engineers are simultaneously reducing time to market and decreasing the cost of development, while increasing the quality and reliability of their products. A driving simulator is the best example of this method and allows virtual designs of control systems, electronic systems, mechanical systems and hydraulic system of a vehicle to be evaluated before costly prototyping. The objective of this Paper is to develop the virtual Proving: ground using a driving simulator and to show its capabilities of an automotive system development tool. For this purpose, including a real-time vehicle dynamics analysis system, the PC-based driving simulator and the virtual proving ground are developed by using VR(Virtual Reality) techniques. Also ABS HIL(Hardware-In-the-Loop ) simulation is performed successfully.

• Journal of the Korea Institute of Military Science and Technology
• /
• v.3 no.1
• /
• pp.13-25
• /
• 2000

A simulation model is developed to analyze the large-structure driving system and its integrated behavior in the whole weapon system. It models every component in the driving system such as mechanical and electrical characteristics, and it is programmed by simulation language in a way which strongly reflects the system's real time dynamics and reduces computation time as well. A useful parameter identification method is proposed, and it is tuned on the given physical system. The model is validated through comparing to real test, and it is applied to analysis and prediction of integrated system functions relating to the fire control system.

• Journal of the Korean Society of Safety
• /
• v.24 no.4
• /
• pp.104-110
• /
• 2009

In this driving simulation study, the impairing effects of various types of electronic devices usage(i. e., destination search by using in-vehicle navigation system, TV watching and dialing cellular phone) during driving on front-to-rear-end collision avoidance were investigated. Percentage of collisions, driving speeds when the drivers collided, and initial reaction time for collision avoidance were analyzed and compared as the dependent measures. The results indicated that (1) any types of electronic devices usage during driving induced more serious collision-related impairment than control condition where no additional task was required, and (2) in general, destination search task appeared to impair drivers collision avoidance performance more than the other task requirements in terms of percentage of collisions and initial reaction time for collision avoidance, but TV watching induced most serious collision impact. These results suggested that any types of electronic device usage could distract drivers attention from the primary task of driving, and be resulted in serious outcome in potentially risky situation of front-to-rear-end collision. In particular, mandatory use of eye-hand coordination and receiving feedback seemed to one of essential factor leading the drivers visual attentional distraction.

• Journal of Mechanical Science and Technology
• /
• v.15 no.6
• /
• pp.720-726
• /
• 2001

This paper describes a vehicle driving-load estimation method for application to vehicle Intelligent Cruise Control (ICC). Vehicle driving-load consists of aerodynamic force, rolling resistance, and gravitational force due to road slope and is unknown disturbance in a vehicle dynamic model. The vehicle driving-load has been estimated from engine and wheel speed measurements using a vehicle dynamic model a least square method. The estimated driving-load has been used in the adaptation of throttle/brake control law. The performance of the control law has been investigated via both simulation and vehicle tests. The simulation and test results show that the proposed control law can provide satisfactory vehicle-to-vehicle distance control performance for various driving situations.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.7 no.6
• /
• pp.222-230
• /
• 1999

A fixed type driving simulator is constructed with a car body, beam projector, operation software , driving scenario, and audio equipments. With the simulator, the cognitive effects of fatigue due to two hour continuous driving of a straight road is investigated . The effects of alcohol on driving performance is also studied. The braking operation and lane keeping performance due to fatigue and alcohol are investigated. Changes of vehicle motion due to these effects are verified by computer simulation.

• Journal of information and communication convergence engineering
• /
• v.5 no.3
• /
• pp.285-288
• /
• 2007

PDP(Plasma Display Panel) driving circuit requires switching devices and capacitors to stand up high voltages over 150volts. Thereby the power consumption and the cost of a PDP driving circuit increase. In this paper, a PDP driving circuit is proposed that can be operated with a lower supply voltage than the supply voltage of conventional driving circuit. The operation of the proposed driving circuit is verified by the computer simulation and experiments. PSPICE simulation and experiments results show that the output signal can drive PDP cells when the supply voltage is higher than 40volts.

• Journal of Drive and Control
• /
• v.20 no.1
• /
• pp.16-26
• /
• 2023

Although the upland field area of Korea is high as 44.8%, the platform optimized for the upland field is insufficient. It is necessary to develop an optimized platform for the upland field because the upland field environment is an irregular environment with many slopes. In addition, due to the characteristic of agricultural operations, the traction power and torque of the platform have to be sufficient. Therefore, in this study, a simulation model that can predict the traction power and driving torque of a crawler-type platform for the upland field was developed and validated using the specifications of the crawler platform. The simulation model was developed using Amesim (19.1, Siemens, Germany). The development of the model was conducted using the specifications of the platform. A measurement system was developed to validate the simulation model. The traction power data of the simulation model was validated with the traction force and vehicle speed. The driving torque data of the simulation model was validated with the torque of the sprocket on the crawler system. As a result of the analysis, the error between measurement and simulation results occurred within 10%, and it was determined that the traction power and driving torque prediction of the crawler platform using this model was possible.