• 한국환경과학회지
• /
• 제27권8호
• /
• pp.677-688
• /
• 2018

The purpose of this study was to minimize salt water intrusion into freshwater aquifers and limit the development of freshwater aquifers, by selecting an appropriate excavation depth of in the western coastal area of Jeju Island. The study site was mostly basaltic lava, which was mainly composed of trachy basalt. A vertical logging test was conducted to investigate the vertical distribution of the groundwater and saline groundwater interface in the study well. It was found that freshwater groundwater, saline groundwater, and freshwater groundwater are distributed from the surface to approximately 16 m, 16~50 m, and 50~60 m, below the ground, respectively. In order obtain saline groundwater and minimize the inflow of freshwater into this well, the drilling depth should be limited in the range of 16~50 m from the surface. Thus, saline groundwater well development should be carried out with reference to the measurement results, which depend on the drilling depth and EC (electrical conductivity) obtained with drilling apparatus for geology and ground handling.

• 한국정밀공학회지
• /
• 제2권3호
• /
• pp.28-40
• /
• 1985

In this study, to check up on the effect of the components of cutting resistance upon friction between drill and inside wall of hole in drilling, the experiment was performed with individual specimen of carbon steel, cast iron, aluminium alloy under various cutting conditions: depth of hole, cutting speed, feed rate, shape and material of specimen. On the basis of the experimental results, the following conclusions are drawn; 1. The components of cutting resis- tance were increased in proportion to the increase of depth of hole owing to frictional resistance of drill margin and chip-jamming. 2. As feed rates increase, torque and thrust were increased. When comparing to the increasing rate for these components respecitively, thrust is higher tendency than torque. 3. As drill diameter increase, torque and thrust were increased. When comparing to the increasing rate for these components respectively, torque is higher tendency than thrust. 4. In the case of torque, the frictional resistance between drill margin and inside wall of drilled hole accounts for about 20 percent of carbon steel, 14 of cast iron, 10 aluminium alloy in drilling. But the effect of thrust force could be negligible. 5. Comparison between the theoretical and experimental results showed a close agreement so far as depth of hole is about three times of drill diameter. But there was a wide difference between them beyond the rane of three times, because of characteristics of the drilling process.

• 한국기계가공학회지
• /
• 제14권1호
• /
• pp.70-77
• /
• 2015

This paper develops and evaluates a mechanical machining process which involves drilling on PVS material. According to the material, two treatment experiments were conducted, one involving drilling in a wet condition or using a lubricant and one involving drilling in a dry condition with no lubricant. Drilling in a dry condition showed better performance in terms of the cutting time than in the wet condition. Otherwise, the wet condition has several advantages. The lubricant influenced the burr diameter size and minimized the temperature on the surface of the work piece. During the wet condition drilling process, a smaller burr diameter size was noted as compared to the dry condition. The temperature showed a linear correlation with the drill bit size, where a least-square analysis provided an $R^2$valuewhichexceeded 0.95. The wet condition required more cutting time than the dry condition. In this condition, the water provides a lubrication effect. A thin layer between the cutting edges and the surface of the work piece is formed. The chip formation is affected by the drilling depth. The color on the tips of the chips was darker than in the initial condition. No correlation between the drilling depth and the bore roughness was noted, but the variation of the cutting speed or the RPM influenced the roughness of the bore. The optimum cutting speed ranged from 40 RPM to 45 RPM in the condition which provided the finest roughness surface.

• 한국공작기계학회논문집
• /
• 제17권4호
• /
• pp.95-103
• /
• 2008

Diamond core drills are applied to drill difficult-to-cut materials. This paper proposes basic understanding of ceramic drilling mechanics and characteristics of main factors affecting tool life, tool wear, cutting force, and chipping thickness. In contrast to conventional drilling, the core drilling process make deep grooves on the workpiece. One difficulty of it is the evacuation of chips from the drilled groove. As the drilling depth increases, an increased amount of chips tend to cluster together and clog the groove. Eventually severe wear develops and diamond grits are separated from the drill body. To relieve the clogging problem and to evacuate chips from the groove easily, the helical drilling process is applied for the core drilling process. To analyze drilling characteristics and derive optimal drilling conditions, tool life, tool wear, cutting force, and chipping thickness are quantified through the monitoring system and the Taguchi method. Mathematical models for the tool life and chipping thickness are derived from the response surface method. Optimal drilling database has been constructed through the experimental models.

• 한국공작기계학회:학술대회논문집
• /
• 한국공작기계학회 1998년도 추계학술대회 논문집
• /
• pp.84-89
• /
• 1998

BTA drilling among the deep hole drilling is using for the improvement of productivity and the high-efficient working. As the deep hole drilling with BTA drill is satisfied with the required quality by one-pass processing, more deeper hole depth, the accuracy of materials is affected by bending vibration and cutting speed. This paper is studied that the shapes of material (surface roughness, roundness) is affected by cutting condition compared actual roundness with lobe shape with modeling of computer through the experiments in the BTA drilling system with BTA drill.

• 한국정밀공학회지
• /
• 제20권8호
• /
• pp.213-220
• /
• 2003

By the localization of electro-chemical dissolution region, we succeeded in a few micrometer size hole drilling on stainless steel with the radial machining gap of about 1 ${\mu}{\textrm}{m}$. Tens of nanosecond duration voltage pulses were applied between WC micro-shaft and stainless steel in the 0.1 M $H_2SO_4$ solution. Pt balance electrode was used to drill the high aspect ratio micro-hole without generation of Cr oxide layer on the machined surface. The effects of applied voltage, pulse duration, and pulse period on localization distance were investigated according to machining time. We suggested the taper reduction technique especially brought up on blind-hole machining. High quality micro-holes with 8 ${\mu}m$ diameter with 20 ${\mu}m$ depth and 12 ${\mu}m$ diameter with 100 ${\mu}m$ depth were drilled on 304 stainless steel foil. The various hole shapes were also produced including stepped holes and taper free holes.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 1994년도 하계학술대회 논문집 C
• /
• pp.1210-1212
• /
• 1994

An amplitude modulation technique for increasing the laser penetration efficiency for metals has been studied. By chopping electro-optically Nd:YAG laser pulse, the threshold energy for reliable hole drilling was decreased significantly and the penetration depth was increased. It was observed that the effect of chopping was optimal at 8-12 kHz with 60% duty cycle. It is believed that this improvement is due to an increase in the vapor recoil pressure and reduced plasma screening.

• Journal of Welding and Joining
• /
• 제6권3호
• /
• pp.37-42
• /
• 1988

The Hole Drilling Method(HDM) is widely used to measure residual stresses in the welded structures. The purpose of this study is to evaluate the accuracy fo measuring residual stresses when drilling the hole by Air-abrasive Jet machine(AJM). Simulated residual stresses wre introduced by applying known stresses to steel bars. These known streses were then compared with measured stresses relaxed from hole drilling. the obtained results are summarized as follows; 1) It was possible to obtain well defined holes with the nozzle designed for this study. 2) If the hole shape is not cylindrical, critical may occur. 3) In the uniaxial strain field, the measurement error of the maximum principal stress was within .+-.10 percent. The orientation angle of the maximum principal stress was within 8.deg. from the given directioin. 4) meausrements were made varying hole depths. Little or no change of stresses occurs since holse were drilled more than the depth of the 0.6 times diameter. 5) The air-abrasive jet machining for drilling holse does not cause appreciable apparent stresses which si critical to measure residual stresses.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2001년도 춘계학술대회 논문집
• /
• pp.513-518
• /
• 2001

As the machining depth increases, the drilling torque increases and fluctuates and the risk of drill failure also increases. Hence, drilling torque control is very important to prevent the drill from failure. In this study, a PID controller was designed to control the drilling torque in a machining center. The plant including the feed drive system, cutting process, and spindle system was modeled for controller design. The Ziegler-Nichols rule was used to determine the controller gain and control action times. The root locus plot was used to tune the controller gain for a certain cutting condition. Also, suggested was a simple method to obtain the tuned controller gain for an arbitrary cutting condition not using the Ziegler-Nichols rule and root locus plot. The cutting torque control, performance of the designed controller and the effect of gain tuning on the control performance were examined.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2001년도 춘계학술대회 논문집
• /
• pp.1064-1067
• /
• 2001

Micro drilling is used in the production of fuel injection nozzle, watch, camera, air bearing and pinted circuit boards(PCB) are demanded for high precision. Recently industries of precision production require more small hole, high aspect ratio and high speed working for micro deep hole drilling. But the undesirable characteristics of micro drilling is the small signal to noise ratios, wandering motion of drill, high aspect ratio and the increase of cutting force as cutting depth increase. So in this paper to obtain the optimization of cutting condition a study on the characteristics of micro deep hole drilling used Tool dynamometer is proposed.