• 한국공작기계학회논문집
• /
• 제12권3호
• /
• pp.8-16
• /
• 2003

Monitoring of the drill wear :md hole quality change is conducted during the drilling process. Cutting force measured by tool dynamometer is a evident feature estimating abnormal state of drilling. One major difficulty in using tool dynamometer is that the work-piece must be mounted on the dynamometer, and thus the machining process is disturbed and discontinuous. Acoustic transducer do not disturb the normal machining process and provide a relatively easy way to monitor a machining process for industrial application. for this advantage, AE signal is used to estimate the abnormal fate. In this study vision system is used to detect flank wear tendency and hole quality, there are many formal factors in hole quality decision circularity, cylindricity, straightness, and so of but these are difficult to measure in on-line monitoring. The movement of hole center and increasement of hole diameter is presented to determine hole quality. As the results of this experiment AE RMS signal and measurements by vision system are shorn the similar tendency as abnormal state of drilling.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 1997년도 춘계학술대회 논문집
• /
• pp.1068-1072
• /
• 1997

This work deals with on investigation the influence of various additives to a base stock cutting fluid in order to develop a better deep hold drilling. This investigation has been aiming at developing an oil which gives a maximum cutting efficiency at a minimum wear rate of the tool and the guiding pads. The purpose of study is to analyze how guide pad of tools, workpiece and the change of contained quantity of extreme pressure additive in cutting fluids have effects on the hold over size of cutting hole, surface roughness of workpiece,wear rates of guide pad and roundness during the deep hole machining of SM55C with solid BTA drill by using BTA drilling system through experiment. Conclusion reached is as follows. It has been proved that the contained quantity of surphur more affects machinability than that of extreme pressure additive of chlorine of cutting fluid in BTA drilling during Deep Hole Drilling. Considering its base oil, the the contained quantity of extreme pressure assitive of surphur can be different, but it's judged that the range of 1.5 ~ 2.0% is suitable to machinability for workpiece in BTA drilling. Regarding guide pad, it's judged that the reduction of wear is possible in propotion to the contained quantity of exrreme pressure additive of chlorine against supporting of cutting force and Bumishing operation of machining parts in cutting.

• The Journal of Korean Physical Therapy
• /
• 제21권4호
• /
• pp.97-102
• /
• 2009

Purpose: The purpose of this study was to investigate the effects of low intensity pulsed ultrasound on TGF-$\beta$1 expression and healing of rat femur penetrating fractures. Methods: Rats were anesthetized with ketamine and xylazine. Using aseptic technique, we exposed the lateral right femoral diaphysis with removal of the periosteum. We made one hole along its long axis with an electrically-driven 1.8 mm diameter drill bit. Postoperatively, rats were divided into two groups (a control group, n=15; an experimental group, n=15). The experimental group was treated with low intensity pulsed ultrasound (pulse rate: 1:4, 0.5 W/$cm^2$, 10 minutes, 1 time per day) for 3 weeks. The control group was treated with sham ultrasound (with the US unit turned off). Results: The experimental group achieved more callus formation and TGF-$\beta$1 expression than the control group at the $7^{th}$, $14^{th}$ and $21^{st}$ days after low intensity pulsed ultrasound treatment. Conclusion: This study suggests that low intensity pulsed ultrasound facilitates bone fracture repair, possibly via increased TGF-$\beta$1 expression.

• Tribology and Lubricants
• /
• 제25권4호
• /
• pp.231-235
• /
• 2009

In this study, the influence of contact pressure on the variation in coefficients of friction between porcine knee joint cartilage and Co-Cr alloy in a repeat pass sliding motion was investigated. Flat-ended cartilage pin specimens(9 mm diameter, 8 mm long) were prepared from porcine(6 months old) knee joints by a drill-type punch. Friction tests were conducted by using a pin-on-disk type friction tester for an hour in PBS lubricated condition under the contact pressures of 0.5, 1 and 2 MPa with 50 mm distance per a cycle at ambient condition. As a result, coefficients of friction increased as the test duration increased for all contact pressures. The maximum coefficients of friction were 0.082, 0.06 and 0.098 for 0.5, 1, and 2 MPa, respectively. It showed that coefficients of friction of porcine knee joint cartilage against Co-Cr alloy depended on the level of contact pressure and related to squeeze film lubrication mechanism.

• 터널과지하공간
• /
• 제6권3호
• /
• pp.197-208
• /
• 1996

Due to the constraints in pre site-investigation for tunnel, it is essential to redesign the support structures suitable for rock mass conditions such as rock strength, ground water and discontinuity conditions for safe tunnel construction. For the selection of optimum support, it is very important to carry out the rock mass classification and in-situ measurement in tunnelling. In this paper, in a mountain tunnel designed by NATM in hard rock, the selectable system for optimum support has been studied. The tunnel is situated at Chun-an in Kyungbu highspeed railway line with 2 lanes over a length of 4, 020 m and a diameter of 15 m. The tunnel was constructed by drill & blasting method and long bench cut method, designed five types of standard support patterns according to rock mass conditions. In this tunnel, face mapping based on image processing of tunnel face and rock mass classification by RMR carried out for the quantitative evaluation of the characteristics of rock mass and compared with rock mass classes in design. Also, in-situ measurement of convergence and crown settlement conducted about 30 m interval, assessed the stability of tunnel from the analysis of monitoring data. Through the results of rock mass classification and in-situ measurement in several sections, the design of supports were modified for the safe and economic tunnelling.

• 한국기계가공학회지
• /
• 제21권9호
• /
• pp.12-20
• /
• 2022

Delamination and burr defects are important problems in drilling fiber reinforced plastics. A method for measuring FRP drilling defects has been studied. Delamination and burr factors were defined as the relative length or area. Using these factors, the effects of tool shape and drilling conditions on delamination and burr were studied. In this study, the defects that occur when drilling a glass-carbon fiber hybrid composite were compared in terms of three factors. In the glass-carbon fiber hybrid composite, the effects of the feed rate and tool point angle on the delamination and burr factors were similar to those in previous studies. The diameter of the tool did not affect the defect factor. A circular burr was generated in a drill tool with a point angle of 184°, and a relatively small deburring factor was observed compared with a tool with a point angle of 140°.

• 한국안전학회지
• /
• 제38권3호
• /
• pp.20-26
• /
• 2023

Fiber-reinforced composite materials with carbon, glass, and aramid fibers are widely applied to industrial field structures due to their excellent properties. However, carbon fibers are vulnerable to external impacts, whereas aramid fibers degrade when exposed to water. This study evaluated carbon/aramid fiber composites degraded and damaged by high-temperature saline environments using acoustic emission (AE). The test specimen was molded using an autoclave and immersed in seawater at 70 ℃ for 224 days. In order to imitate the damage, a 3-mm-diameter hole was drilled using a diamond drill. Additionally, the specimen with the perforation was repaired by patch attachment processing. Three-point bending was used to conduct the flexural experiment, and an AE sensor with a 150-kHz resonance frequency was attached to evaluate the damage and the effect of patch attachment. AE accumulative counts obtained at the maximum load were 69.2, 67.1, and 91.2 for a high-temperature seawater deteriorated condition, a hole specimen, and a repaired patch specimen, respectively. Furthermore, the maximum amplitude of AE was detected at low values of 28 dB, 31.3 dB, and 30.3 dB.

• 대한관절경학회지
• /
• 제10권2호
• /
• pp.209-213
• /
• 2006

목적: 기존의 경경골 대퇴 터널 천공 방법은 11시 혹은 1시 방향으로 수직에 가까워 술 후 전후방 안정성은 있으나 회전력에 대한 안정성을 제공하지 못한다는 문제가 제기되어 저자들은 10시 혹은 2시 방향으로 경경골 대퇴 터널을 천공하는 수술 수기를 소개하고자 한다. 수술 술기: 10시 또는 2시 방향의 경경골 대퇴터널을 만들기 위해서는 경골 drill guide의 위치와 방향이 중요하다. 저자들은 경골 drill guide의 각도를 $40{\sim}45$도로 하고 관절내 guide tip을 고식적인 위치보다 1 mm씩 전방 및 내측으로 이동하였다. 경골에서 유도 강선의 시작점은 거위발 건의 근위부, 내측 측부 인대의 내측부로 하였으며 경골의 장축과 유도 강선의 각은 $30{\sim}40$도로 하여 경골 offset guide가 10시 또는 2시의 대퇴 터널 방향으로 쉽게 향하도록 하였다. 경골 터널은 먼저 이식건의 두께보다 1 mm작은 확공기를 이용하여 만들고 다시 이식물과 같은 크기의 확공기를 이용하여 30 mm 깊이의 대퇴 터널과 경골 터널을 완성하였다. 결론: 전방 십자 인대 재건술시 전후방 안정성뿐만 아니라 회전력에 대한 안정성을 제공하기 위하여 경골 터널을 통하여 10시 혹은 2시 방향에 대퇴 터널을 천공하는 수술 수기를 소개하였다.

• 한국산학기술학회논문지
• /
• 제21권10호
• /
• pp.259-266
• /
• 2020

사면안정공법 중 락볼트 공법은 터널이나 흙막이공법에도 널리 적용되는 공법이나 불안정한 지반을 보강하기 위한 축력이 시간이 경과됨에 따라 감소되고 천공된 원지반과 충진재 사이의 강도가 현저히 줄어들어 내구성이 떨어지거나 설계 성능을 발현하지 못하는 문제가 발생하고 있다. 본 연구는 성능저하 문제를 해결할 수 있는 요철형 굴착공법 개발을 목표로 드릴링 장비의 개발 및 적용성 평가를 수행하였다. 개발된 드릴비트의 성능평가를 위해 100MPa이상의 암석을 확공굴착 하여 검증하였고, 요철형성 효과에 대한 평가를 위해 요철유무에 따른 실험체를 제작하여 성능실험 및 평가를 수행하였다. 실험결과 요철이 형성된 모델은 요철이 없는 모델의 인발저항 임계하중인 468.7kN의 약 1.7배로 평균값 801.6kN을 나타내어 그 효과를 충분히 확인하였다. 암석과 그라우트 접촉면이 파괴되기 전 암석의 취성으로 인해 실험체가 먼저 파괴되어 요철형성 모델의 임계하중 측정은 불가능 했으나, 암석 파괴하중 도달 전 그라우트 충진부의 슬립이 전혀 발생하지 않았고, 암석파괴시의 하중이 요철이 없는 모델의 임계하중을 충분히 넘어선 점을 감안하면 요철 확공직경이 20mm 증가했음에도 불구하고 저항능력이 획기적으로 늘어날 것으로 기대된다. 향후 최적 요철형성 락볼트 공법개발을 위한 수치해석 모델개발 및 변수연구와 추가 실험에 본 연구의 결과가 기초자료로 활용될 수 있을 것으로 판단된다.

• 대한관절경학회지
• /
• 제13권1호
• /
• pp.82-85
• /
• 2009

목적: 전방 십자 인대 재건술시 잔류조직 보존은 이식건 치유를 향상시키고 고유수용 감각 기능을 보존할 수 있어 저자들은 10시 혹은 2시 방향 경경골 대퇴 터널을 천공하고 잔류조직을 보존하는 술기를 소개하고자 한다. 수술 술기: 잔류조직은 가능한 많이 보존하고자 하였으며 그 중에서 경골 부착부위 전방부와 후방 십자 인대와 연결된 활액막 및 잔류조직은 반드시 보존하여 잔류조직의 장력을 어느정도 유지하고 흘러내림을 방지하여 과간 절흔의 충돌을 방지 하였다. 경골 drill guide의 각도를 40~45도로 하고 관절 내 guide tip을 고식적인 위치보다 1 mm씩 전방 및 내측으로 이동하였다. 경골에서 유도 강선의 시작점은 거위발 건의 근위부, 내측 측부 인대의 전방부로 하였다. 경골 터널은 먼저 이식건의 두께보다 1 mm 작은 확공기를 이용하여 만들되, 경골 관절면의 피질골에 닿으면 조심스럽게 진행하여 피질골을 뚫자마자 멈춤으로써 가능한 잔류조직에 손상이 가지 않도록 하였으며, 다시 이식물과 같은 크기의 확공기를 이용하여 경골 터널과 10시 혹은 2시 방향의 대퇴 터널을 완성하였다. 결론: 전방 십자 인대 재건술시 10시 혹은 2시 방향 경경골 대퇴 터널을 천공하고 잔류조직을 보존하는 술기를 소개하였다.