• 기술사
• /
• 제23권6호
• /
• pp.41-46
• /
• 1990

First of all, Under given condition such as bit gage of 36mm Drill bit with right class of jack-logs experimental test carried out from two face of Bench, firing of each hole brought 90 degree Angle face and them measured length of Burden and charged ammount of powder as following. (equation omitted) A=Activated Area A=ndi=m S=Peripheral length of Charged. room Ca=Rock Coeffiecency d : di=Hole diameter When constructed subway of Seoul in 1980 the blasting works increased complaint of ground vibration. in order to prevent the damage to structures. Some empirical equations were made as follows on condition with Jackleg Drill (Bit Gage ø 36mm) and within 30 meter distance between blasting site and structures. V=K(D / W)$\^$-n/ N=1.60-1.78 K=48-138 Project one of contineous works to above a determination of empirical equation on the cautious blasting vibration with Crawler Drill(ø 70-75mm) in long distance. V=41(equation omitted) V=124(equation omitted).

• 화약ㆍ발파
• /
• 제8권3호
• /
• pp.3-13
• /
• 1990

First ot of all, under given condition such as bit gage of 36mm Drill bit with right class of jack-leg-experimental test carried out from two face of Bench, firing of each hole brought 90 degree Angle face and them measured length of Burden and charged ammount of powder as following. $ca=\frac{A}{SW}$ A=Activated Area A=nd i=m S=Peripheral length of charged, room Ca=Rock Coeffiecency d: di=Hole diameter When constructed subway of Seoul in 1980 the blasting works increased complaint of ground vibration, in order to prevent the damage to structures. Some empirical equations were made as follows on condition with Jackleg Drill (Bit Gage 36mm) and within 30 meter distance between blasting site and structures. $V=K(D/W)^{-n}$ N=1.60 - 1.78 K= 48 - 138 Project is one of contineous works to above a determination of empirical equation on the cautious blasting vibration with Crawler Drill (70-75mm) in long distance. $V=41(D/\sqrt[3]{W})^{-1.41}$ $30m\le{D}\le{100m}$ $V=124(D/\sqrt[3]{W})^{-1.66}$ $100m\le{D}\le{285m}$.

• 한국구조물진단유지관리공학회 논문집
• /
• 제27권1호
• /
• pp.64-70
• /
• 2023

본 연구에서는 1.04배 드릴비트 직경 및 1.02배 드릴비트 직경 시 앵커의 신뢰성시험을 수행하였다. 각 변수별 시험을 통해 앵커의 표준편차 및 변동계수를 검토하였고, 기준시험 결과와 비교 평가하였다. 1.04배 드릴비트 직경을 가진 M12 및 M16 앵커의 신뢰성시험결과, 극한 인장하중 허용기준 변동계수 값인 20% 이내의 값을 나타내어 시험기준을 만족하였다. 또한, 1.04배 드릴비트 직경을 가진 앵커의 성능은 기준시험 대비 M12 앵커는 약 74%, M16 앵커는 약 55% 정도로 나타나 앵커의 내력이 다소 부족한 성능을 나타냈지만, 설계강도 대비 약 253% 및 210%로 나타나 1.04배 드릴비트 직경에 설치된 앵커의 인발성능은 충분히 확보하고 있음을 알 수 있었다. 1.02배 드릴비트 직경을 가진 M12 및 M16 앵커의 신뢰성시험결과, 극한인장하중 허용기준 변동계수 값인 20% 이내의 값을 나타내어 시험기준을 만족하였다. 또한, 1.02배 드릴비트 직경을 가진 앵커의 성능은 기준시험 대비 M12 앵커는 약 48%, M16 앵커는 약 53% 정도로 나타나 다소 부족한 성능을 나타냈지만, 설계강도 대비 약 136% 및 168% 로 나타나 1.02배 드릴비트 직경에 설치된 앵커의 인발성능은 충분히 확보하고 있음을 알 수 있었다.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2013년도 춘계학술대회 논문집
• /
• pp.269-270
• /
• 2013

• Knee surgery & related research
• /
• 제30권4호
• /
• pp.364-368
• /
• 2018

We report a case of 53-year-old woman with an injured popliteal artery due to excessive drilling with a drill bit during medial opening wedge high tibial osteotomy (MOWHTO). Pseudoaneurysm was diagnosed three days after surgery and confirmed by urgent computed tomography (CT) angiography. Open vascular surgery with resection of the perivascular hematoma and end-to-end anastomosis using ipsilateral saphenous vein interposition graft was performed. CT angiography at 8 months postoperatively showed that blood flow was maintained without obstruction of the graft site and active dorsiflexion of the foot was possible. To reduce neurovascular injury during MOWHTO, it is important not to drill the far cortex at the proximal part of the osteotomy site when using a drill bit, and the metal should be positioned posteromedially as much as possible.

• 한국터널지하공간학회 논문집
• /
• 제3권4호
• /
• pp.17-24
• /
• 2001

본 연구에서는 시공여건이 유사한 도로터널 4개소을 선정하여 실내시험 및 막장지질조사를 실시하였고 그 결과와 점보드릴을 활용하여 얻을수 있는 비트마모율과 굴착지수의 상관관계를 지보패턴별로 분석하였다. 연구대상 4개 도로터널에 대한 평균비트마모율은 지보패턴별로 11.85%에서 3.25%로 차이를 보였고 굴착지수는 주로 파쇄대의 발달정도에 따라 변동이 발생하였다.

• 한국정밀공학회지
• /
• 제30권2호
• /
• pp.223-230
• /
• 2013

When a new nuclear fuel is developed, an irradiation test needs to be carried out in the research reactor to analyze the performance of the new nuclear fuel. In order to check the performance of a nuclear fuel during the irradiation test in the test loop of a research reactor, sensors need to be attached in and out of the fuel rod and connect them with instrumentation cables to the measuring device located outside of the reactor pool. In particular, to check the temporary temperature change at the center of a nuclear fuel during the irradiation test, a thermocouple should be instrumented at the center of the fuel rod. Therefore, a hole needs to be made at the center of fuel pellet to put in the thermocouple. However, because the hardness and the density of a sintered $UO_2$ pellet are very high, it is difficult to make a small fine hole on a sintered $UO_2$ pellet using a simple drilling machine even though we use a diamond drill bit made by electro deposition. In this study, an automated drilling machine using a CVD diamond drill has been developed to make a fine hole in a fuel pellet without changing tools or breakage of workpiece. A sintered alumina ($Al_2O_3$) block which has a higher hardness than a sintered $UO_2$ pellet is used as a test specimen. Then, it is verified that a precise hole can be drilled off without breakage of the drill bit in a short time.

• 한국정밀공학회지
• /
• 제30권1호
• /
• pp.113-119
• /
• 2013

To develop a new nuclear fuel, it needs to make a test fuel rod and carry out burn-up test in the test loop of a research reactor to check the irradiation characteristics of the nuclear fuel. At that time, several sensors such as thermocouples, LVDTs and SPNDs are needed to be attached in and out of the fuel rod and connect them with instrumentation cables. Then, the instrumentation cables deliver the signals measured by the sensors to the measuring device located outside of the reactor pool. In particular, to install a thermocouple in a fuel rod, it needs to drill off holes on the alumina blocks and sintered $UO_2$ pellets. However, because the hardness of a sintered $UO_2$ pellet is 700 Hv (or HRC 61) and that of an alumina block is 1480 Hv, a special drilling machine which adapts a diamond coated drill bit had developed. In this study, several case experiments have been carried out to find an optimal drilling condition of the drilling machine. And, using the optimal drilling condition, minimum numbers of the holes that a drill bit can drill off are verified.

• 소음진동
• /
• 제7권4호
• /
• pp.669-679
• /
• 1997

This paper deals with a study of striker type impact hammer drill for improving the drilling performance. The study was performed through a numerical simulation of the impact hammer mechanism and an experimental comparison of the numerical simulation results was followed. Optimization of the impact mechanism was also performed. The numerical model of the impact hammer drill takes into account the striker motion and the effects of the pressure in the cylinder as well as the friction acting on the striker. The equation of motion is solved with the pressure equation in the cylinder including the friction force. The friction is considered as a combination of Coulomb friction and viscous damping friction. At the moment of impact, an ideal impact model that uses restitution coefficient is used to calculate the sudden change of the striker motion. The numerically simulated impact force shows a good agreement with the experimental result and thus, the validity of the numerical model is proven. Based upon the proposed model, an optimization was performed to improve the impact force of the hammer drill. The objective function is to maximize the impact force and the used design variables are striker mass, frequency of piston, bit guide mass, cylindrical diameter and dimensions of the mechanism components. Each design variable and some other conditions that are essential to manitain normal operation of the hammer drill are considered as constraints. The optimized result show a remarkable improvement in impact force and an experimental proof was investigated.

• 한국해양공학회지
• /
• 제28권2호
• /
• pp.111-118
• /
• 2014

In drilling process of oil wells, the drilling fluid such as mud keeps the drill bit cool and clean during drilling, with suspending drill cuttings and lubricating a drill bit. In this paper, a commercial CFD package(ANSYS Fluent 15.0) was used to solve the hydrodynamic force and evaluate mud mixing time in the mud mixing tank on offshore drilling platforms. Prediction of power consumption in co-rotating and counter-rotating models has been compared with results of Nagata's correlation equation. This research shows the hydrodynamic effect inside the two phase mud mixing tank according to rotating directions(co-rotating and counter-rotating). These results, we can conclude that the co-rotating direction of the two shafts with mixing blade in the mud mixing tank can be a preferable in power consumption and mixing time reduction.