• 대한금속재료학회지
• /
• 제47권5호
• /
• pp.274-282
• /
• 2009

To investigate the evolution of deformation texture in dual phase (DP) steels during deep-drawing deformation, deep-drawing experiments were performed. Microtexture measurements were conducted using electron backscattered diffraction (EBSD) to analyze texture evolution. A rate-sensitive polycrystal model was used to predict texture evolution during deep-drawing deformation. In order to evaluate the strain path during deep-drawing deformation, a steady state was assumed in the flange part of a deep-drawn cup. A ratesensitive polycrystal model successfully predicted the texture evolution in DP steels during deep-drawing deformation. The final stable orientations were found to be strongly dependent on the initial location in the blank. Texture analysis revealed that the deep drawability of DP steels decreases as the true strain in the radial direction of the deep-drawn cup increases during deep-drawing deformation.

• 소성∙가공
• /
• 제29권2호
• /
• pp.69-75
• /
• 2020

The plastic strain ratio is one of the factors that affect the deep drawability of metal sheets. The plastic strain ratio of fully annealed Cu sheet is low, due to its texture being {001}<100>. In this study, in order to increase the plastic strain ratio of Cu sheets we investigated the effect of two treatments: 1^st the sheet was asymmetrically rolled and annealed, and 2^nd the sheet was symmetrically and asymmetrically rolled and subsequently annealed. The average plastic strain ratio (R_m) of the initial Cu sheet was 0.95 and |Δr| was 1.27. After the 2^nd treatment of 5.3% symmetric rolling and annealing of Cu sheet at 1000℃ for 60 min in Ar gas condition, the R_m was 2.29 times higher and the |Δr| was 1.44 times higher than that of initial Cu sheet specimen. After the 2^nd treatment of 8.2% asymmetric rolling and annealing of Cu sheet at 1000℃ for 60 min in Ar gas conditions, the R_m was 2.51 times higher and |Δr| was 0.53 times lower than that of the initial Cu sheet specimen. These results can be attributed to the change in texture of the Cu sheets due to the differences in the two methods of rolling.

• 소성∙가공
• /
• 제23권8호
• /
• pp.489-494
• /
• 2014

Micro forming is an appropriate process to manufacture very small metal parts which can be employed in the field of electronic devices or electrically controlled mechanical systems. The purpose of the current study was to investigate the influences of both blankholding force and blank diameter for the deep drawing of very small cups. It is essential to control the blankholding force because improper force can result in defects such as wrinkles in the flange or cracks in the corner of the drawn cups. In the current study blankholding force was controlled by springs connected to the blankholder of a press die. Exchangeable bushing dies with various die-corner radii were also used. To obtain the limit drawing ratio for each working condition several sizes of circular specimens were prepared using blanking tools. Beryllium copper(C1720) alloy sheet of $50{\mu}m$ thickness was chosen for the experiments. The maximum limit drawing ratio of 2.1 was achieved experimentally for the conditions of the blankholder force(BHF)=5.3kgf and Rd=0.3mm. Both thickness and hardness along the central section of drawn cups were measured and compared for different drawing conditions. It was found that the deviation of measured data in the thickness and hardness distribution increases with increasing blankholder force and blank diameter.

• 비파괴검사학회지
• /
• 제17권4호
• /
• pp.270-277
• /
• 1997

소성이방성은 판재의 가공성을 결정하는 중요한 인자로써 주로 기계적인 인장시험에 의해 측정되고 평가되어 왔다. 압연 방향에 대하여 상대적인 방향으로 진행하는 초음파의 속도로부터 집합조직의 결정분포함수를 구할 수 있으며, 결정분포함수의 계수인 결정방위계수는 소성이방성의 평균값들과 상관 관계를 갖는다. 본 실험에서는 초음파 속도로 구한 결정방위계수와 압연강판의 소성이방성을 비교하여 서로의 상관 관계를 구하였으며, 측정결과 average normal anisotropy, $\bar{\gamma}$는 ${\pm}0.082$, average planar anisotropy, ${\Delta}r$는 ${\pm}0.096$의 편차 내에서 예측 가능하였다. 초음파 속도 측정에는 공진주파수측정법이 적용되었고, 초음파의 송수신에는 EMAT가 이용되었다.

• 한국주조공학회지
• /
• 제20권2호
• /
• pp.122-128
• /
• 2000

Strip casting process is a new technology that makes a near net shape thin strip directly from molten metal. With this process, a large amount of energy and casting cost could be decreased from the abbreviation of reheating and/or hot rolling process. Ductile cast iron which has spheroidal graphite in the matrix is the most commercial and industrial material, because of its supreme strength, toughness, and wear resistance etc. But it cannot be produced to the thin strip owing to difficulty in rolling of ductile cast iron. In this study, ductile cast iron strips are produced by the twin roll strip caster, with different chemical compositions of C, Si, and Mn contents. And then heat-treated, microstructures and mechanical properties are examined. The microstructures of as-cast strip are that of white cast iron which consists of the mixture of cementite and pearlite, but the equiaxed crystal zone of the pearlite or segregation zone of cementite exists in the center region of the strip thickness, which cannot be observed in the rapidly solidified metallic mold cast specimens. This structure is supposed to be formed from the thermal distribution of strip and the rolling force. Comparing with the structures of each strips after heat treatment, increasing Si content makes smaller spheroidal graphite and more compact in the matrix, furthermore the less of Mn content makes the ferrite matrix be obtained clearer and easier. As a result of the tensile test of graphitization heat-treated strips, the yield strengths are about 250 MPa, the tensile strengths are about $430{\sim}500$ MPa, and the elongations are about $10{\sim}13%$. In the case of the strip which has the smaller and more compact spheroidal graphite in the ferrite matrix, the higher tensile strength and better drawability could be obtained.

• 한국재료학회지
• /
• 제3권1호
• /
• pp.43-49
• /
• 1993

AI킬드한 극저탄소강에 Ti, Nb등의탄화물 또는 질화물 형성원소를 첨가하면 우수한 디프드로잉특성과 내시효성을 나타내는 강판을 얻을 수 있다고 알려져 있으므로 본 연구에서는 Ti및 Nb를 단독 또는 동시에 첨가하거나 B를 추가로 첨가한 고강도 극저탄소 강판을 제조하여 각각의재결정 집합조직과 기계적 성질을 측정비교하여 보았다. 역극점도에 나타난 집합조직강도의 변화를 조사한 결과 어닐링처리에 의하여 (100)면 강도와 (111)면 강도의 변화가 가장 많이 나타난 것은 Nb첨가강이며, Nb와 Ti를 단독으로 첨가한 강과 Ti를 단독으로 첨가한 강은 변화정도가 비슷하였다.극점도를 비교하면,Nb와 Ti를 동시에 첨가한강, Nb를 단독으로 첨가한 강 그리고 Ti를 단독으로 첨가한강 모두 냉간 압연한 상태에서는{112}<110>집합조직이 발달하였으며 어닐링처리한 후에는 {111}<112>집합조직이 잘 발달하였다. 그러나 세 종류의 강간에 집합조직의 차이는 별로 없었다. 결정립도와 관계가 깊은 경도에서는 결정립도가 가장 작은 Nb 및 Ti동시첨가강에서 경도가 가장 높고, Nb단독첨가강, Ti단독첨가강의 순서로 감소하는 경향을 보였다.

• 한국재료학회지
• /
• 제3권2호
• /
• pp.131-139
• /
• 1993

극저탄소 알루미늄 킬드강내에 합금원소로 첨가된 Al, Ti, Nb, B등은 열처리 공정중 질화물이나 탄화물로 석출되어 강의 재결정집합조직을 변화시킴으로써 강판재의 디입드로잉 특성에 결정적인 영향을 미친다. 본 연구에서는 Ti및 Nb를 단독으로 또는 동시에 첨가한 데 이어, B, P, Si 및 Mn등을 추가로 첨가한 극저탄소 고강도 강판의 집삽조직에 미치는 질화물, 탄화물과 같은 미세 석출물의 영향을 TEM, SEM, 광학현미경분석에 의하여 조사하였다. Nb 및 Ti를 동시에 첨가한 강에서는 미세한 N$b_2$C 및 T$i_2$AIN가 주로 석출되는 반면, Nb를 단독으로 첨가한 강에서는 미세한 AIN 및 조대한 BN이 석출되고,Ti를 단독으로 첨가한 강에서는 비교적 조대한 T${i_4}{N_3}$및 조대한 ${N_10}{N_22}$/T$i_68$이 석출되는 것으로 관찰되었다. 또한 이러한 탄질화물들의 석출에 의하여 세 강이 서로 다른 결정입도를 나타내는데, 결정입도는 Nb 및 Ti동시첨가강과 Nb단독첨가강이 서로 비슷하고, Ti단독첨가강이 가장 큰 것으로 나타났다.