• 한국안전학회지
• /
• 제12권3호
• /
• pp.17-22
• /
• 1997

This paper reals with the structure and function of duel mass flywheel. Damping effects of engine rotational fluctuation are compared with those of pre-damper clutch and duel mass flywheel and driven- system behavior is estimated engine idle r.p.m. The reason of gear rattle noise is higher in summer than winter and driving longer period than initial driving is due to affection by drag torque changing. The above-contents can be used on the design of clutch system and transmission matching including engine and duel mass flywheel.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 1994년도 춘계학술대회논문집; 영남대학교, 20 May 1994
• /
• pp.100-105
• /
• 1994

본 연구에서는 변속기 중립상태에서 클러치 설계 인자인 비틀림 스프링과 건마찰에 의해서 클러치에 나타나는 히스테리시스, 그리고 클러치 디스크의 정적처짐을 발생시키는 드래그토크(drag torque)가 클러치의 동적인 거동과 기어래틀에 미치는 영향을 분석하고자 한다.

• EDISON SW 활용 경진대회 논문집
• /
• 제5회(2016년)
• /
• pp.614-618
• /
• 2016

본 논문은 EDISON_CFD를 활용하여 화성에서 운용 가능한 풍력터빈에 대해 실험 및 개선 설계하였다. 본 연구에서는 화성의 중력 및 공기밀도 등 화성의 환경 데이터를 적용함으로써 풍력터빈의 형상을 새롭게 설계 하였다. 개선 설계는 기존의 풍력발전기 형상을 변형시키며 해석을 진행하였으며, 받음각과 형상에 따라 생성되는 토크를 확인하였다. 개선설계한 풍력터빈 모델은 단위 미터 당 약 8 W의 전력생산이 가능한 것을 확인하였다.

• Tribology and Lubricants
• /
• 제14권1호
• /
• pp.70-78
• /
• 1998

Two different friction materials (organic and low-metallic pads) for automotive brakes were studied to investigate the anti-fading phenomena during stop. The anti-fading phenomena were pronounced more in the case of using low metallic friction materials than organic friction materials. The main cause of the anti-fading phenomena was the high dependence of friction coefficient on a sliding speed. The anti-fading was prominent when the initial brake temperature was high in the case of low-metallic friction materials due to the strong stick-slip event at high temperature. On the other hand, the anti-fading was not severe in organic friction materials and the effect was reduced at high braking temperature due to the thermal decomposition of organic friction materials. The strong stickslip phenomena of low metallic friction materials at high temperature induced high torque oscillations during drag test. During this experiment two different braking control modes (pressure controlled and torque controlled modes) were compared. The type of the control mode used for brake test significantly affected the friction characteristics.

• 한국전산유체공학회:학술대회논문집
• /
• 한국전산유체공학회 2008년도 춘계학술대회논문집
• /
• pp.652-655
• /
• 2008

Despite of the laminar-turbulent transition region co-exist with fully turbulence region around the leading edge of an airfoil, still lots of researchers apply to fully turbulence models to predict aerodynamic characteristics. It is well known that fully turbulent model such as standard k-${\varepsilon}$ model couldn't predict the complex stall and the separation behavior on an airfoil accurately, it usually leads to over prediction of the aerodynamic characteristics such as lift and drag forces. So, we apply correlation based transition model to predict aerodynamic performance of the NREL (National Renewable Energy Laboratory) Phase IV wind turbine. And also, compare the computed results from transition model with experimental measurement and fully turbulence results. Results are presented for a range of wind speed, for a NREL Phase IV wind turbine rotor. Low speed shaft torque, power, root bending moment, aerodynamic coefficients of 2D airfoil and several flow field figures results included in this study. As a result, the low speed shaft torque predicted by transitional turbulence model is very good agree with the experimental measurement in whole operating conditions but fully turbulent model(k-${\varepsilon}$) over predict the shaft torque after 7m/s. Root bending moment is also good agreement between the prediction and experiments for most of the operating conditions, especially with the transition model.

• Wind and Structures
• /
• 제22권6호
• /
• pp.703-721
• /
• 2016

This paper presents a wind tunnel study of wind loads of the large billboard structures with two-plate and three-plate configurations. Synchronous dynamic pressures on the surfaces of plates are measured, and the characteristics of local pressures, integrated forces on each individual plate and on the overall structures are investigated. The influences of wind direction and plate configuration on wind load characteristics, and the contributions of overall crosswind load and torque to the stress responses are examined. The results showed that the wind load characteristics of windward plate in both two- and three-plate configurations are very similar. The contribution of overall crosswind load makes the total resultant force from both alongwind and crosswind loads less sensitive to wind direction in the case of three-plate configuration. The overall torque is lower than the value specified in current codes and standards, and its contribution is less significant in both two-plate and three-plate configurations.

• Tribology and Lubricants
• /
• 제40권1호
• /
• pp.1-7
• /
• 2024

Ball bearings are a major component of mechanical parts for transmitting rotation. Compared to tapered roller bearings, ball bearings offer less rolling resistance, which leads to reduced heat generation during operation. Because of these characteristics, ball bearings are widely used in electric vehicles and machine tools. The design of ball bearing cages has recently emerged as a major issue in ball bearing design. Cage design requires pre-verification of performance using theoretical or experimental formula or computational fluid dynamics (CFD). However, CFD analysis is time-consuming, making it difficult to apply in case studies for design decisions and is mainly used in performance prediction following design confirmation. To use CFD in the early stages of design, main-taining analytical accuracy while reducing the time required for analysis are necessary. Accordingly, this study proposes a laminar steady-state segment CFD technique to solve the problem of long CFD analytical times and to enable the use of CFD analysis in the early stages of design. To verify the reliability of the CFD analysis, a bearing drag torque test is performed, and the results are compared with the analytical results. The proposed laminar steady-state segment CFD technique is expected to be useful for case studies in bearing design, including cage design.

• Tribology and Lubricants
• /
• 제13권1호
• /
• pp.34-41
• /
• 1997

Frictional behavior of three automotive friction materials (brake pads) containing different amounts of antimony trisulfide ($Sb_2S_3$) and zirconium silicate ($ZRSiO_4$) were investigated using a front brake system. The friction materials were tested on a brake dynamometer (dyno) with gray cast iron rotors. The dynamometer(dyno) test simulated the dragging of a ehicle maintaining 70 km/h and vehicle stops from 100 km/h using 20 different combinations of initial brake temperature (IBT) and input pressure (IP). The results showed a strong influence of the relative amount of $Sb_2S_3$ and $ZrSiO_4$ in friction materials on friction characteristics. Friction stability was improved with the higher concentration of $Sb_2S_3$ in the friction material. Torque variation during drag cycle was increased with an increase of the $ZrSiO_4$ concentration in the friction material. Average friction coefficient and the wear rate of the friction material increased by using more aggressive friction materials containing more $ZrSiO_4$ and less $Sb_2S_3$. Generation of the disk thickness variation (DTV) increased when friction materials with higher concentration of $ZrSiO_4$ were used Careful examination of DTV change showed that aggressiveness of the friction material played an important role in determining torque variation.

• 대한조선학회논문집
• /
• 제54권1호
• /
• pp.18-25
• /
• 2017

This study deals with numerically comparing performance according to rudder shape called 'Twisted rudder and Wavy twisted rudder'. In comparison with conventional rudder, rudder with wavy shape has showed a better performance at high angles of attack($30^{\circ}{\sim}40^{\circ}$) due to delaying stall. But most of study concerned with wavy shape had been performed in uniform flow condition. In order to identify the characteristics behind a rotating propeller, the present study numerically carries out an analysis of resistance and self-propulsion for KCS with twisted rudder and wavy twisted rudder. The turbulence closure model, Realizable $k-{\epsilon}$, is employed to simulate three-dimensional unsteady incompressible viscous turbulent and separation flow around the rudder. The simulation of self-propulsion analysis is performed in two step, because of finding optimization case of wavy shape. The first step presents there are little difference between twisted rudder and case of H_0.65 wavy twisted rudder in delivered power. So two kind of rudders are employed from first step to compare lift-to-drag ratio and torque at high angles of attack. Consequently, the wavy twisted rudder is presented as a possible way of delaying stall, allowing a rudder to have a better performance containing superior lift-to-drag ratio and torque than twisted rudder at high angles of attack. Also, as we indicate the flow visualization, check the quantity of separation flow around the rudder.

• 한국기계가공학회지
• /
• 제9권2호
• /
• pp.12-19
• /
• 2010

The characteristics of the torsional systems are generally examined with the nonlinearities such as the several staged clutch damper springs, gear backlashes and drag torques. Generally speaking, the system's characteristics can be found out by the eigensolutions which can show the system natural frequencies and the mode shapes. However, these factors can not give the complete solutions to avoid the noise and vibration problems related to the nonlinear effects. Therefore, several assumptions should be made for solving the real physical system problems under the linear analysis which can reflect the nonlinear effects in the torsional system. This means that the several modified linear factors such as the modified clutch damper spring constants can be used to examine and avoid the natural frequency zones related to the noise and vibration problems. Under the linear analysis with the assumed and modified values, the system can be investigated with the more reliable ways for the realistic phenomena.