• Journal of the Korea Society of Computer and Information
• /
• v.18 no.4
• /
• pp.113-121
• /
• 2013

In this paper, simulations were carried out to determine the efficiency of the rotation efficiency according to the draft of waterwheel in open rectangular channel. In the small hydroelectric generators to get the highest efficiency of waterwheel is very important. But the presence of various elements(free water surface flow, non-uniform velocity distribution because of the waterways wall friction etc) makes it difficult to create a mathematical formula. In this paper, we made a scale model and perform a physical simulation where the draft, gradient and flux is variable. Scale modelling with 10-step draft, 3-step gradients and 2-step flux, as well were constructed then computerized automatic experimental system were configured to acquire the rotational efficiency vs. draft of itself. Rotational efficiency is analyzed as for the draft of waterwheel using the acquired data by varying the gradient and flux of canal. Reviewing the analyzed data, it is confirmed that phenomena of efficiency shown at previous and present experiment is similar and revealed that computerized system shows more sophisticated numerical figures.

• THE INTERNATIONAL COMMERCE & LAW REVIEW
• /
• v.77
• /
• pp.145-168
• /
• 2018

The purpose of this paper is to introduce the limitation of liabilities of multimodal transport operators(MTO) in Korea. Also, this paper reviews the revised draft of Korean Commercial Code in 2015. This paper analyzes Korean multimodal transport systemand the limitation of liabilities of MTO by analyzing articles, regulations and practices of Korean Commercial Code and it's the draft in 2015. The paper, also, studies multimodal transport rules by comparing specifically international treaty, rules, or practices. In Korea, Article 816 of Commercial Code treats multimodal transportation adopting the network liability regime. The Article describes only the case of the multimodal transportation where the maritime carriage is engaged. Korea proposed the draft of multimodal transport regulation of Commercial Code in 2015 because present law could not apply for the multimodal transportation involved in the air or land carriage. This paper support the draft of Korean Commercial Code in 2015 because it is necessary to make a predictable legal system of multimodal transport and the limitation of liability reflecting practices or customs.

• Journal of Biosystems Engineering
• /
• v.3 no.2
• /
• pp.35-61
• /
• 1978

To find out the power tiller's travel and tractive characteristics on the general slope land, the tractive p:nver transmitting system was divided into the internal an,~ external power transmission systems. The performance of power tiller's engine which is the initial unit of internal transmission system was tested. In addition, the mathematical model for the tractive force of driving wheel which is the initial unit of external transmission system, was derived by energy and force balance. An analytical solution of performed for tractive forces was determined by use of the model through the digital computer programme. To justify the reliability of the theoretical value, the draft force was measured by the strain gauge system on the general slope land and compared with theoretical values. The results of the analytical and experimental performance of power tiller on the field may be summarized as follows; (1) The mathematical equation of rolIing resistance was derived as $$Rh=\frac {W_z-AC \[1+ \frac{sl}{K} \(\varrho ^{-\frac{sl}{K}-1\)\] sin\theta_1}} {tan\phi \[1+ \frac{sl}{K} \(\varrho ^{-\frac{sl}{K}-1\)\]+\frac{tan\theta_1}{1}$$ and angle of rolling resistance as $$\theta _1 - tan^1\[ \frac {2T(AcrS_0 - T)+\sqrt (T-AcrS_0)^2(2T)^2-4(T^2-W_2^2r^2)\times (T-AcrS_0)^2 W_z^2r^2S_0^2tan^2\phi} {2(T^2-W_z^2r^2)S_0tan\phi}\] $$and the equation of frft force was derived as$$P=(AC+Rtan\phi)\[1+ \frac{sl}{K} \(\varrho ^{-\frac{sl}{K}-1\)\]cos\phi_1 \ulcorner \frac {W_z \ulcorner{AC\[ [1+ \frac{sl}{K} \(\varrho ^{-\frac{sl}{K}-1\)\]sin\phi_1 {tan\phi[1+ \frac{sl}{K} \(\varrho ^{-\frac{sl}{K}-1\]+ \frac {tan\phi_1} { 1} \ulcorner W_1sin\alpha $$The slip coefficient K in these equations was fitted to approximately 1. 5 on the level lands and 2 on the slope land. (2) The coefficient of rolling resistance Rn was increased with increasing slip percent 5 and did not influenced by the angle of slope land. The angle of rolling resistance Ol was increasing sinkage Z of driving wheel. The value of Ol was found to be within the limits of Ol =2\ulcorner "'16\ulcorner. (3) The vertical weight transfered to power tiller on general slope land can be estim ated by use of th~ derived equation: $$R_pz= \frac {\sum_{i=1}^{4}{W_i}} {l_T} { (l_T-l) cos\alpha cos\beta \ulcorner \bar(h) sin \alpha - W_1 cos\alpha cos\beta$$The vertical transfer weight $R_pz$ was decreased with increasing the angle of slope land. The ratio of weight difference of right and left driving wheel on slop eland,$\lambda= \frac { {W_L_Z} - {W_R_Z}} {W_Z} $, was increased from ,$\lambda$=0 to$\lambda$=0.4 with increasing the angle of side slope land ($\beta = 0^\circ~20^\circ) (4) In case of no draft resistance, the difference between the travelling velocities on the level and the slope land was very small to give 0.5m/sec, in which the travelling velocity on the general slope land was decreased in curvilinear trend as the draft load increased. The decreasing rate of travelling velocity by the increase of side slope angle was less than that by the increase of hill slope angle a, (5) Rate of side slip by the side slope angle was defined as $ S_r=\frac {S_s}{l_s} \times$ 100( %), and the rate of side slip of the low travelling velocity was larger than that of the high travelling velocity. (6) Draft forces of power tiller did not affect by the angular velocity of driving wheel, and maximum draft coefficient occurred at slip percent of S=60% and the maximum draft power efficiency occurred at slip percent of S=30%. The maximum draft coefficient occurred at slip percent of S=60% on the side slope land, and the draft coefficent was nearly constant regardless of the side slope angle on the hill slope land. The maximum draft coefficient occurred at slip perecent of S=65% and it was decreased with increasing hill slope angle $\alpha$. The maximum draft power efficiency occurred at S=30 % on the general slope land. Therefore, it would be reasonable to have the draft operation at slip percent of S=30% on the general slope land. (7) The portions of the power supplied by the engine of the power tiller which were used as the source of draft power were 46.7% on the concrete road, 26.7% on the level land, and 13~20%; on the general slope land ($\alpha = O~ 15^\circ ,\beta = 0 ~ 10^\circ$) , respectively. Therefore, it may be desirable to develope the new mechanism of the external pO'wer transmitting system for the general slope land to improved its performance.l slope land to improved its performance.

• Journal of Biosystems Engineering
• /
• v.3 no.2
• /
• pp.34-34
• /
• 1978

To find out the power tiller's travel and tractive characteristics on the general slope land, the tractive p:nver transmitting system was divided into the internal an,~ external power transmission systems. The performance of power tiller's engine which is the initial unit of internal transmission system was tested. In addition, the mathematical model for the tractive force of driving wheel which is the initial unit of external transmission system, was derived by energy and force balance. An analytical solution of performed for tractive forces was determined by use of the model through the digital computer programme. To justify the reliability of the theoretical value, the draft force was measured by the strain gauge system on the general slope land and compared with theoretical values. The results of the analytical and experimental performance of power tiller on the field may be summarized as follows; (1) The mathematical equation of rolIing resistance was derived as $$Rh=\frac {W_z-AC \[1+ \frac{sl}{K} \(\varrho ^{-\frac{sl}{K}-1\)\] sin\theta_1}} {tan\phi \[1+ \frac{sl}{K} \(\varrho ^{-\frac{sl}{K}-1\)\]+\frac{tan\theta_1}{1}$$ and angle of rolling resistance as $$\theta _1 - tan^1\[ \frac {2T(AcrS_0 - T)+\sqrt (T-AcrS_0)^2(2T)^2-4(T^2-W_2^2r^2)\times (T-AcrS_0)^2 W_z^2r^2S_0^2tan^2\phi} {2(T^2-W_z^2r^2)S_0tan\phi}\] $$and the equation of frft force was derived as$$P=(AC+Rtan\phi)\[1+ \frac{sl}{K} \(\varrho ^{-\frac{sl}{K}-1\)\]cos\phi_1 ? \frac {W_z ?{AC\[ [1+ \frac{sl}{K} \(\varrho ^{-\frac{sl}{K}-1\)\]sin\phi_1 {tan\phi[1+ \frac{sl}{K} \(\varrho ^{-\frac{sl}{K}-1\]+ \frac {tan\phi_1} { 1} ? W_1sin\alpha $$The slip coefficient K in these equations was fitted to approximately 1. 5 on the level lands and 2 on the slope land. (2) The coefficient of rolling resistance Rn was increased with increasing slip percent 5 and did not influenced by the angle of slope land. The angle of rolling resistance Ol was increasing sinkage Z of driving wheel. The value of Ol was found to be within the limits of Ol =2? "'16?. (3) The vertical weight transfered to power tiller on general slope land can be estim ated by use of th~ derived equation: $$R_pz= \frac {\sum_{i=1}^{4}{W_i}} {l_T} { (l_T-l) cos\alpha cos\beta ? \bar(h) sin \alpha - W_1 cos\alpha cos\beta$$The vertical transfer weight $R_pz$ was decreased with increasing the angle of slope land. The ratio of weight difference of right and left driving wheel on slop eland,$\lambda= \frac { {W_L_Z} - {W_R_Z}} {W_Z} $, was increased from ,$\lambda$=0 to$\lambda$=0.4 with increasing the angle of side slope land ($\beta = 0^\circ~20^\circ) (4) In case of no draft resistance, the difference between the travelling velocities on the level and the slope land was very small to give 0.5m/sec, in which the travelling velocity on the general slope land was decreased in curvilinear trend as the draft load increased. The decreasing rate of travelling velocity by the increase of side slope angle was less than that by the increase of hill slope angle a, (5) Rate of side slip by the side slope angle was defined as $ S_r=\frac {S_s}{l_s} \times$ 100( %), and the rate of side slip of the low travelling velocity was larger than that of the high travelling velocity. (6) Draft forces of power tiller did not affect by the angular velocity of driving wheel, and maximum draft coefficient occurred at slip percent of S=60% and the maximum draft power efficiency occurred at slip percent of S=30%. The maximum draft coefficient occurred at slip percent of S=60% on the side slope land, and the draft coefficent was nearly constant regardless of the side slope angle on the hill slope land. The maximum draft coefficient occurred at slip perecent of S=65% and it was decreased with increasing hill slope angle $\alpha$. The maximum draft power efficiency occurred at S=30 % on the general slope land. Therefore, it would be reasonable to have the draft operation at slip percent of S=30% on the general slope land. (7) The portions of the power supplied by the engine of the power tiller which were used as the source of draft power were 46.7% on the concrete road, 26.7% on the level land, and 13~20%; on the general slope land ($\alpha = O~ 15^\circ ,\beta = 0 ~ 10^\circ$) , respectively. Therefore, it may be desirable to develope the new mechanism of the external pO'wer transmitting system for the general slope land to improved its performance.

• Journal of Power System Engineering
• /
• v.14 no.5
• /
• pp.30-35
• /
• 2010

Recently, the large capacity draft fans in power plants had been changed to variable speed type to educe the power consumption. But the fan experienced the unexpected vibration at specific speed regions. In this study, the high vibration frequency of the fan was confirmed and the natural frequency of the rotor were measured and analyzed by FEM programs. It was analyzed that the vibration was caused by the resonance at the frequency, 30.7Hz. So, the rotor vibration characteristic was changed by adjusting the distance between the shaft bearings. It was conformed the high vibration was disappeared over the all operation speeds.

• Journal of Biosystems Engineering
• /
• v.18 no.4
• /
• pp.328-343
• /
• 1993

To control depth of tractor implement, an automatic depth control system based upon microcomputer was developed. This system consists of data aquisition system to measure and to record travel speed, draft and depth of the implement, hydraulic system to control the implement depth and 3-point hitch to attach the implement. Program, written in C language, was able to select position control, draft control and mixed control. To analyze parameters affecting this system, the performance of the system was evaluated through use of computer simulation and verified in soil bin experiments. 3-point hitch was lifted by hydraulic pressure and lowered by implement weight. Dead band was one of the important factors which affect the stability and the accuracy of the system. The system became unstable when the flow rate was increased or when the dead band was decreased. The position control mode with on-off control showed the great ability to control the implement at the given plowing depth. With the draft control, the tractor load could be reduced, however the plowing depth was changed unexpectedly when the soil was hard and inconsistent. The mixed control could improve the performance of the system to maintain the plowing depth without overload of the tractor.

• THE INTERNATIONAL COMMERCE & LAW REVIEW
• /
• v.20
• /
• pp.467-493
• /
• 2003

There are situations in e-commerce that are altogether new and to which the existing rules cannot apply. The uncertainty and business risk is too high for trading partners to deal with certainty. Therefore existing law must be changed to e-commerce law so that it provides certainty and enforceability in the e-commerce. Legal rules applying to the commerce and international commerce, in particular, contracts, proper law, jurisdiction and so on, have improved with time and experience. It has been found that the problems arising in the context of e-contracting were due to the absence of experience in electronic contracting and an absence of knowledge on how best to solve the problems. Thus, UNCITRAL Working Group on Electronic Commerce held an extensive discussion on issues related to electronic contracting and prepared and revised the Preliminary Draft Convention on International Contracts Concluded or Evidenced by Data Message from the thirty-ninth session in 2002 and prepared the Draft Convention from forty-first session which applies to international contracts concluded or evidenced by means of data messages. An electronic contract is concluded when the acceptance of an offer becomes effective, and an offer becomes effective when it is received by the offeree, and an acceptance of an offer becomes effective when the indication of assent is received by the offeror according to this Convention. Electronic contract may be concluded by the interaction of an automated computer system and natural person or by the interaction of automated computer systems, and a contract formed by a natural person that accesses an automated computer system of another person has no legal effect in case the neutral person made a material error in a data message. The purpose of this paper is to raise the understanding of the Convention on the Electronic Contracting by studying the contents of Draft Convention on Electronic Contracting and comparing Draft Convention with preliminary Draft Convention and finding the difference, characteristics and problem.

• Journal of Korean Society of Industrial and Systems Engineering
• /
• v.19 no.39
• /
• pp.81-88
• /
• 1996

As international commerce pattern changes toward the system of developed countries market competition, developing countries experience difficulties in international commerce market. Developed countries request their trading counterparts to obtain environment restriction. We also endure the environmental pollution due to industrialization. These environmental problems force Western Europe countries to install Environment Management System. This article presents description of development processes of ISO 14000 draft, compares ISO 9000 with 7750 requirements, and describes the common points and differences between ISO 9000 and 14000 draft.

• Journal of the Korean Society for Precision Engineering
• /
• v.16 no.2 s.95
• /
• pp.68-73
• /
• 1999

Generally, most of machining processes are done according to the dimention of the draft made by CAD. However, there are many cases that a sample is given without the draft because of the simplicity of the shape in the machining of 2D objects. To cut the same shape as the given sample, this paper proposes the method to extract the geometric information about a large sample using the robot vision and to draw the demensional draft for the machining. Because the resolution of one frame in the vision system is too low, it is necessary to set up a camera according to the desired resolution and to capture the image moving along the contour. And the overall outline can be compounded of the sequentially captured images. In the experiment, we compared the product after the cutting with the original sample and found that the size of two objects was coincided within the allowed error bound.

• The Magazine of the Society of Air-Conditioning and Refrigerating Engineers of Korea
• /
• v.7 no.4
• /
• pp.227-238
• /
• 1978

Draft of the conbustion gab burning in a briquette gives a great part of driving force to the flue gas in an Korean conventional ondol heating system. The Paper present s how the draft intensity varies for each whole Combustion duration. In this experiment the temperatures of thirty spots In three gas courses of a briquette were measured and the drafts were calculated form those experimental data. The result is that the shorter the combustion duration of a briquette is, the stronger the draft becomes, the intensity of drafts ranging between 0.15mm Aq to 0.26mm Aq.