• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.18 no.8
• /
• pp.24-30
• /
• 2019

This study investigated the heat dissipation characteristics of a heat-sensitive LED. The results of the empirical test showed that the best temperature intensification was found at 90 with 15-fins, and the heatsink installed perpendicular to the direction of the flow of air was directly connected to the air in the largest heat shield area, leading to the best cooling, and the number of fin also resulted increase in the heat discharge area, resulting in the largest cooling action with 15 fins. It was found that the rate of air flow changed in the range of 1.5m/s to 2.5m/s, but only by a deviation of about $2^{\circ}C$ to $3^{\circ}C$ from the current state of 15 fins at 2.5m/s, and the rate of air flow increased, but the performance of the heat release was not significantly increased. As a result wind speed with minimum air flow conditions of 1.5m/s can greatly contribute to the heat dissipation performance.

• Proceedings of the SAREK Conference
• /
• 2006.06a
• /
• pp.953-958
• /
• 2006

Perimeter zone has been reinforced by active systems, such as fan-coil units, because it causes an increase in heating and cooling loads, dew condensation in winter, or discomfort with cold-draft to residents in buildings, through poor insulation by light-weighed skin due to progressing multi-storied buildings and skyscrapers. However, because these active systems raise Its capacity so that fossil fuel is used as much as they are added, and ultimately, greenhouse effect is urged, we proposed BIPV system functioned as solar collector which can substitute active system. As an early stage, heat balance equation in steady-state by Fortran was used not only for pre-heating effect and electric power capacity during the day in winter, but also for electric power capacity during day in slimmer and sky radiation effect during night in summer. Especially, we should have considered shading on PV, since even a little bit of it makes the efficiency too low for the PV to work. Still, when the flux of pre-heated air was increased to make air-barrier, its temperature was not enough to make it because the speed of heat exchange was too fast to warm up the air, thus the capacity to meet the condition was evaluated, and electric power from PV was made used for it.

• Journal of the Korean Society of Marine Environment & Safety
• /
• v.27 no.3
• /
• pp.409-420
• /
• 2021

The decrease in under keel clearance (UKC) due to the increase of draft that occurs during advancing and turning of very large vessels of different types was analyzed based on computational fluid dynamics (CFD). The trim change in the Duisburg test case (DTC) container ship was much smaller than that of the KRISO very large crude oil carrier 2 (KVLCC2). The sinkage of both ships increased gradually as the water depth became shallower. The amount of sinkage change in DTC was greater than that in KVLCC2. The maximum heel angle was much larger for DTC than for KVLCC2. Both ships showed outward heel angles up to medium-deep water. However, when the water depth became shallow, an inward heel was generated by the shallow water effect. The inward heel increased rapidly in very shallow water. For DTC, the reduction ratio was very large at very shallow water. DTC appeared to be larger than KVLCC2 in terms of the decreased UKC because of shallow water in advancing and turning. In this study, a new result was derived showing that a ship turning in a steady state due to the influence of shallow water can incline inward, which is the turning direction.

• Steel and Composite Structures
• /
• v.48 no.4
• /
• pp.429-441
• /
• 2023

This research presents an advanced finite element formulation for analyzing the vibratory behaviour of tapered composite shaft rotors, taking into account the impact of the draft angle on the stiffness of the composite shaft laminate. The vibration response of the shaft rotating around its axis is studied using both the finite element hierarchical method and the classical finite element formulation, based on the theory of transverse shear deformation, rotary inertia, gyroscopic effect, and coupling effect due to the stratification of the composite layers of the shaft. The study also includes the development of a program to calculate the Eigen frequencies and critical speeds of the system, and the obtained results are compared with those available in the literature. This research provides valuable insights into the vibratory behaviour of tapered composite shaft rotors and can be useful for designing and optimizing such structures in various industrial applications.

• Korean Journal of Agricultural Science
• /
• v.49 no.4
• /
• pp.677-696
• /
• 2022

Development of radish collectors may enhance radish production and promote upland crop mechanization in the Republic of Korea. Theoretical analysis of power is crucial to ensure the optimum design of agricultural machinery. The aim of the present study is to analyze theoretically the power requirement of a tractor-mounted radish collector under development and to propose design guidelines. The important components of the radish collector were belt-type conveyors, three hydraulic motors, and a direct current (DC) winch motor to operate the total radish collecting process. Theoretical equations were used to calculate the hydraulic motor's power, winch motor power, and draft power at loaded and unloaded conditions. A variety of tractors (44 - 74 kW) and different soil characteristics (hard, firm, tilted, and sandy) were considered to investigate the appropriate drawbar power. Variations of the power requirement of the tractor-mounted radish collector were observed due to modifications of the design parameters. The required hydraulic power of the stem cutting conveyor, stem cutting blade, and transfer conveyor of the radish collector were 0.23 and 0.24, 0.18 and 0.19, and 0.19 and 0.22 kW under unloaded and loaded conditions, respectively. The maximum draft power was calculated as 0.89, 1.07, 1.25, and 1.61 kW at a 30° tilted angle for hard, firm, tilted, and sandy soil, respectively. The calculation showed 2.07 kW DC power was required for unfolding or folding the stem-cutting conveyor. A maximum power of 4.78 kW was prescribed for conducting the whole process of the tractor-mounted radish collector. The analysis of power introduced in this study will be helpful to select the appropriate design parameters for the successful development of a tractor-mounted radish collector.

• Journal of the Korean Society of Marine Environment & Safety
• /
• v.27 no.7
• /
• pp.1106-1115
• /
• 2021

In this study, a fin that controls ship stern flow was attached on stern hull of a 80k bulk carrier to improve resistance performance. The rectangular cross-sectional fin was attached at several locations on the hull, and angle to streamline was changed with constant length, breadth, and thickness. The resistance performance and wake on propeller plane of the hull with and without the fin were analyzed using model-scale computational fluid dynamics simulation. The analysis results were extrapolated to full-scale to compare the performance and wake of the full-scale ship. First, the fin changed path of bilge vortex that flowed into the propeller along the stern hull without the fin to transom stern. This change increased pressure of the stern hull and upper region of the propeller, so pressure resistance and total resistance of the hull were reduced - the nearer the fin location to after perpendicular (AP) and base line of the hull, the larger the reduction of the resistances. Second, nominal wake fraction of the hull with the fin was lower than that without the fin. This dif erence was in proportion to the angle of the fin, but the total resistance reduction was in proportion until a certain angle at which the reduction was maximum. The largest total resistance reduction was approximately 2.1% at 12.5% of length between perpendiculars from the AP, 10% of draft from the base line, and 14° with respect to the streamline.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.18 no.3
• /
• pp.768-776
• /
• 1994

This paper describes computer-aided forging design for rib/web shaped parts. In manufacturing a part by means of forging process, the first step is to design the forging. This is done by modifying the given machined part geometry according to the requirements of the forging process. Traditionally, this is done by experienced forging designers using empirical forging design guidelines. Generally, it would be neither possible nor practical to develop a system which encompasses the design of all types of forgings. Accordingly, forging design can be simplified by considering critical two dimensional cross sections of the machined part geometry. This system is composed of three modules(process variable decision module, forging design module and redesign module) and each module is carried out in regular sequence. In the process variable decision module, first of all, the undercut is checked and modified, and then deep recesses and holes difficult to forge are eliminated. Also parting line, forging plane, forging plan view area, forging weight and maximum size(maximum height or width)are determined. In the forging design module, the magnitude of various allowances, draft angle, minimum web thickness, corner and fillet radius are determined and then geometry modification is performed. Finally, since the design rules and databases used in this system are based on parameters of the forging geometry, such as the trimmed forging plan area, forging weight, forging maxmum size, plausible estimates need to be made for these parameters. Therefore, in the re-design module, the design process is iterated until a satisfactory forging is obtained.

• Journal of Advanced Marine Engineering and Technology
• /
• v.40 no.7
• /
• pp.574-579
• /
• 2016

Grid systems used in previous studies were determined to be valid only if the length between the perpendiculars in a model ship was in the range of 6-8 m, and the maximum dynamic trim angle was smaller than $1^{\circ}$. The application of the grid system to a small fishing boat can create numerical instability because the dynamic trim of small boats is generally larger than $3^{\circ}$, and their Froude numbers are in the range of 0.3-0.8. In the present study, resistances of a small fishing boat were stably obtained by reducing the length between the center of buoyancy and the inlet boundary of the numerical domain, and by refining grid cells vertically in a region that would be swept by a free surface. The effective power of the small fishing boat was predicted based on the ITTC-1978 two-dimensional analysis. By using the results of previous towing tank tests, the coefficient of quasi-propulsive efficiency and the brake horsepower at a design draft were calculated.

• Journal of the Korean Institute of Navigation
• /
• v.10 no.2
• /
• pp.97-114
• /
• 1986

Ship's maneuverability is very important factor in safe ship handling and economical ship operation. Steering characteristics are consisted of course stability and maneuverability. Today in many advanced ship-building countries, they study ship's course stability, using model ship tests, such as straight line tests, rotating arm tests and Planar Motion Mechanism (PMM) etc., in tow in tanks. It is the purpose of this paper to provide ship's handlers with better understanding of steering characteristics and to help them in safe controlling and manevering . In this paper, the author simulated response of various vessels, running straight course with constant speed, and they are disturbed by small external disturbance of one degree yaw angle with no angular velocity . The author used the hydrodynamic derivtives resulted at tests of Davidson's laboratory in Stevens Institute of Technology, New Jersey, U.S.A. Course stability was evaluated and analyzed in various respects, such as block coefficient, ratio of ship's length to beam, draft and rudder area ratio etc. The obtained results are as follows : (1) The ship's course stability is affected by magnitude of block coefficient greatly. In case that the block coefficient is more than 0.7, the deviation varies at nearly same rate but the requistite time to reach the steady course is different. (2) The ship's course stability is affected by magnitude of L/B. When the dimensionless time reaches about 3, the deviation and requisite time to reach the steady course are influenced nearly same. After the dimensionless time is about 3, they change on invariable ratio. (3) The effect to course stability by L/T and RA' can be neglected. (4) The reason why thy VLCC and container feeder vessel are unstable on their course is that their block coefficient is generally more than 0.8 and the ratio of ship's length to beam is about 6.0.

• Proceedings of the Korea Water Resources Association Conference
• /
• 2019.05a
• /
• pp.267-267
• /
• 2019

Driftwood is one of serious problems in a river environment. In several countries, such as Indonesia, Japan, and Italy, the driftwood frequently appears in a river basin, and it can alter the channel bed, flow configuration by wood deposition and jam formation. Therefore, the studies related to driftwood have been actively conducted by many researchers to understand the mechanism of driftwood dynamics. In particular, wood motion by collision is one of the difficult issues in the numerical simulation because the calculation for wood collision requires significantly expensive calculation time due to small time step. Thus, this study conducted the numerical simulation in consideration of the wood motion by water flow and wood collision to understand the wood dynamics in terms of computation. We used the 2D (two-dimensional) depth-averaged velocity model, Nays2DH, which is a Eulerian model to calculate the water flow on the generalized coordinate. A Lagrangian type driftwood model, which expresses the driftwood as connected sphere shape particles, was employed to Nays2DH. In addition, the present study considered root wad effect by using larger diameter for a particle at a head of driftwood. An anisotropic bed friction was considered for the sliding motion dependent on stemwise, streamwise and motion directions. We particularly considered changeable draft at each particle and projection area by an angle between stemwise and flow directions to precisely reproduce the wood motions. The simulation results were compared with experimental results to verify the model. As a result, the simulation results showed good agreement with experimental results. Through this study, it would be expected that this model is a useful tool to predict the driftwood effect in the river flow.