• Journal of Mechanical Science and Technology
• /
• 제14권10호
• /
• pp.1131-1142
• /
• 2000

In an effort to illustrate the global variation of SMD (Sauter mean diameter, or $D_{32}$) and AMD (Arithmetic mean diameter, or $D_{10}$) at five axial downstream locations (i. e., at Z=30, 50, 80, 120, and 170 mm) under the different experimental conditions, the radial coordinate is normalized by the spray half-width. Experimental data to analyze the atomization characteristics concerning with an internal mixing type have been obtained using a PDPA(Phase Doppler Particle Analyzer). The air injection pressure was varied from 40 kPa to 120 kPa. In this study, counterflowing internal mixing nozzles manufactured at an angle of $15^{\circ}$with axi-symmetric tangential-drilled four holes have been considered. By comparing the results, it is clearly possible to discern the effects of increasing air pressure, suggesting that the disintegration process is enhanced and finer spray droplets can be obtained under higher air assist. The variations in $D_{32}$ are attributed to the characteristic feature of internal mixing nozzle in which the droplets are preferentially ejected downward with strong axial momentum, and dispersed with the larger droplets which are detected in the spray centerline at the near stations and smaller ones are generated due to further subsequent breakup by higher shear stresses at farther axial locations. The poor atomization around the centre close to the nozzle exit is attributed to the fact that the relatively lower rates of spherical particles are detected and these drops are not subject to instantaneous breakup in spite of the strong axial momentum. However, substantial increases in SMD from the central part toward the edge of the spray as they go farther downstream are mainly due to the fact that the relative velocity of droplet is too low to cause any subsequent disintegration.

• 한국항공우주학회지
• /
• 제34권1호
• /
• pp.18-23
• /
• 2006

본 연구에서는 Gurney 플랩이 달린 NACA 0012 익형에 대한 플러터 해석을 시간 영역에서 수행하였다. 2차원 비정상 압축성 Navier-Stokes 방정식과 Lagrange 방정식으로 부터 유도한 2계 자유도 plunge & pitch 모델을 지배방정식으로 하여 연성 결합 기법을 통해 플러터 해석을 수행하였다. 계산 결과 Gurney 플랩을 장착할 경우 NACA 0012에 비해 플러터가 발생하는 속도가 낮아졌고, 마하수가 0.85보다 작은 영역에서는 Gurney 플랩의 플러터 경계 곡선은 안전 여유를 상회하는 영역에 위치하였다. 그러나, 마하수가 0.85에서 0.9사이일 경우에는 안전 여유에 근접하게 되므로 이러한 운용 영역에서는 Gurney 플랩의 사용에 주의를 요한다.

• Bulletin of the Korean Chemical Society
• /
• 제35권2호
• /
• pp.436-440
• /
• 2014

The ${\alpha}$-Effect; Ground state; Transition state; Intramolecular H-bonding; Yukawa-Tsuno plot; Second-order rate constants for aminolysis of 2-chloro-4-nitrophenyl X-substituted-benzoates (1a-h) have been measured spectrophotometrically in 80 mol % $H_2O/20$ mol % DMSO at $25.0^{\circ}C$. The Br${\emptyset}$nsted-type plot for the reactions of 2-chloro-4-nitrophenyl benzoate (1d) with a series of primary amines curves downward, which has been taken as evidence for a stepwise mechanism with a change in rate-determining step (RDS). The Hammett plots for the reactions of 1a-h with hydrazine and glycylglycine are nonlinear while the Yukawa-Tsuno plots exhibit excellent linearity with ${\rho}_X=1.22-1.35$ and ${\gamma}= 0.57-0.59$, indicating that the nonlinear Hammett plots are not due to a change in RDS but are caused by stabilization of substrates possessing an electron-donating group (EDG) through resonance interactions between the EDG and C=O bond of the substrates. The ${\alpha}$-effect exhibited by hydrazine increases as the substituent X changes from a strong EDG to a strong electron-withdrawing group (EWG). It has been concluded that destabilization of hydrazine through the electronic repulsion between the adjacent nonbonding electrons is not solely responsible for the substituent dependent ${\alpha}$-effect but stabilization of the transition state is also a plausible origin of the ${\alpha}$-effect.

• 한국공간구조학회논문집
• /
• 제17권2호
• /
• pp.21-32
• /
• 2017

The objective of this study is to analysis the mechanical characteristics on the geometric nonlinear behavior of radial cable roof systems for long span retractable cable roof structures. The retractable roof is designed as a full control system to overcome extreme outdoor environments such as extreme hot or cold weather, strong wind or sunlight, and the cable roof greatly can reduce roof weight compared to other rigid structural system. A retractable cable roof system is a type of structures in which the part of entire roof can be opened and closed. The radial cable roof is an effective structural system for large span retractable roofs, the outer perimeter of the roof is a fixed membrane roof and the middle part is a roof that can be opened and closed. The double arrangement cables of a radial cable truss roof system with reverse curvature works more effectively as a load bearing cables, the cable system can carry vertical load in up and downward direction. In this paper, to analyze the mechanical characteristics of a radial cable roof system with central posts, the authors will investigate the tensile forces of bearing cables, stabilized cables, ring cables, and the deflection of roof according to the height of the post or hub that affects the sag ratio of cable truss. The tensile forces of the cables and the deflection of the roof are compared for the cases when the retractable roof is closed and opened.

• 대한화학회지
• /
• 제39권11호
• /
• pp.848-855
• /
• 1995

평판형 열장흐름분획법에서 중력효과에 의한 polystyrene(PS)와 polymethylmethacrylate(PMMA)의 머무름 거동에 관하여 연구하였다. 하향 이동상 흐름의 경우 이동상 흐름 방향과 같은 방향으로 작용하는 중력 효과는 수평면 으로부터 장치각도가 0.deg.에서 60.deg.까지 변화함에 따라 증가하였다. 이 효과는 PS와 PMMA의 머무름 시간을 작게 하였고, 무차원 변수 .lambda.의 값을 증가시켰다. 그리고 분자량이 다른 두개의 고분자 머무름 시간차를 감소시켜 분리기능 저하시켰다. 상향 이동상 흐름의 경우 이동상 흐름의 반재 방향으로 작용하는 중력 효과는 수평면으로부터 장치의 각도가 0.deg.에서 60.deg.까지 증가함에 따라 증가하였다. 이 효과는 PS와 PMMA의 머무름 시간을 크게 하였고, 무차원 변수.lambda.의 값을 감소 시켰다. 그리고 분자량이 다른 두 개의 고분자 머무름 시간 차를 증가시켜 분리능을 향상시켰다.

• 태양에너지
• /
• 제19권4호
• /
• pp.71-80
• /
• 1999

본 연구는 예비실험에서 나타난 평판 및 모서리형 현장 열저항 측정기의 내부공기 온도편차를 줄일 수 있는 방안을 모색하기 위한 것으로 연구결과 다음과 같은 결론을 얻을 수 있었다. 첫째, 측정기의 크기에 따라 기기내의 온도편차는 큰 변화가 없으므로 사용과 운반이 용이한 소형이 적정하며 둘째, 방열판의 위치는 측정기 Casing을 통한 부수적인 손실열량을 최소화하기 위해 측정기 내부 표면과 이격시켜 설치하고 셋째, 방열판의 온도는 측정기내부온도가 실내온도까지 접근하는 도달시간을 고려하여 가능한 한 낮게 설정하고 넷째, 측정기 내부에 설치되는 팬은 측정기의 상부에 설치하여 기류를 하향으로 토출하며 다섯째, 방열판 앞에는 Baffle Plate를 설치하는 것이 기기내의 온도편차를 줄일 수 있는 유효한 방법임을 알 수 있었다.

• 한국운동역학회지
• /
• 제18권3호
• /
• pp.71-82
• /
• 2008

본 연구의 목적은 $20^{\circ}$ 경사로에 서 앞 뒤 보행 동작 시 지면반력 형태를 비교 분석하고자 한다. 본 연구를 위해서 두 대의 지면 반력기를 통해 전 후, 좌 우, 수직 지면반력값, 최대값, 최소값, 평균값 압력 중심 변위, 부하율과 감소율을 측정하였다. BD보행 시 RTO 시점에서 수직 지면반력값이 FU 보행에 비해 유의하게 높은 수치를 보인 반면, $RHC_2$ 시점에서는 더 낮은 수치를 보였다. 이는 보행 동작의 차이와 보행 시 발목과 무릎의 위치 변화, 무게 중심의 변화가 지면 반력의 형태에 직접적인 영향을 미치는 것으로 판단되어진다. 전 후 압력중심변위는 하향 보행 시 상향 보행에 비해 낮은 변화를 보였는데 이는 하향 시 생기는 불안정성을 상쇄하기 위해 더 강한 제동력이 발생되어 진 것으로 사료되어 진다. BD보행 시 부하율이 다른 보행에 비해 낮은 것을 알 수 있는데 이러한 결과를 통해 등산로에서 후방 보행 동작이 하지 근골격계에 지속적인 스트레스를 감소시켜 상해를 예방할 수 있는 방법으로 제시될 수 있을 것이다.

• Advances in nano research
• /
• 제8권1호
• /
• pp.59-68
• /
• 2020

In the present study, buckling analysis of sandwich composite (carbon nanotube reinforced composite and fiber reinforced composite) Euler-Bernoulli beam in two configurations (core and layers material), three laminates (combination of different angles) and two models (relative thickness of core according to peripheral layers) using differential quadrature method (DQM) is studied. Also, the effects of porosity coefficient and different types of porosity distribution on critical buckling load are discussed. Using sandwich beam, it shows a considerable enhancement in the critical buckling load when compared to ordinary composite. Actually, resistance against buckling in sandwich beam is between two to four times more. It is also showed the critical buckling loads of laminate 1 and 3 are significantly larger than the results of laminate 2. When Configuration 2 is used, the critical buckling load rises about 3 percent in laminate 1 and 3 compared to the results of configuration 1. The amount of enhancement for laminate 3 is about 17 percent. It is also demonstrated that the influence of the core height (thickness) in the case of lower carbon volume fractions is ignorable. Even though, when volume fraction of fiber increases, differences grow smoothly. It should be noticed the amount of decline has inverse relationship with the beam aspect ratio. Among three porosity patterns investigated, beam with the distribution of porosity Type 2 (downward parabolic) has the maximum critical buckling load. At the end, the first three modes of buckling will be demonstrated to investigate the effect of spring constants.

• 한국기계가공학회지
• /
• 제18권5호
• /
• pp.103-109
• /
• 2019

The pressure reducing valve for water is controlled by the load of the compression spring and the force of the fluid acting on the diaphragm of the stem. Repeated upward and downward reciprocation of the pressure-reducing valve stem damages the diaphragm, resulting in leakage. In this study, we designed a stem without a diaphragm and adjusted the stiffness of the compressing spring. In order to select the spring stiffness, springs offering a stiffness of -20%, -10%, 0%, and 10% with respect to the stiffness of the compression spring attached to the existing pressure reducing valve stiffness. A prototype for the pressure reducing valve was fabricated and the pressure change was evaluated for the target static pressure (6 bar) by testing the pressure characteristics after mounting the modified stem and each compression spring. Evaluation of the pressure characteristics was carried out using ASSE 1003 and KS B 6153. In addition, the flow rates were compared by internal flow analysis of the conventional pressure reducing valve and the pressure reducing valve using the modified stems, and the flow analysis was performed using Solidworks flow simulation 2018. The spring stiffness was constantly discharged at the target static pressure of 3.793 kgf/mm, and the flow rate was increased by about 15% compared with the conventional pressure reducing valve.

• Journal of Korean Neurosurgical Society
• /
• 제66권4호
• /
• pp.393-399
• /
• 2023

Objective : Chiari II malformation (CM II) is still the main cause of severe morbidity and mortality in children with open neural tube defects (ONTDs). The goal of this study was to validate a CM II model in late-stage chick embryos with surgically induced ONTDs. Methods : To make the chick embryo model of ONTD, their neural tubes were opened for a length of 5-6 somites at the thoracic level in Hamburger and Hamilton stage 18 chick embryos (n=150). They were reincubated in ovo up to a total age of 17-21 days. A total of 19 embryos survived and were assigned to either the postoperative day (POD) 14-15 group (n=6) or the POD 17-18 group (n=13). Magnetic resonance imaging (MRI) and histopathologic findings of embryo heads with spinal ONTDs were compared with age-matched normal chick embryos. Results : The chick embryos with ONTDs demonstrated definite and constant structural changes, such as downward displacement of the cerebellum to just above the foramen magnum and narrow and small cerebrospinal fluid spaces in the crowded small posterior fossa. These morphologic features were more prominent in the POD 17-18 group than in the POD 14-15 group. Conclusion : This is the first description of CM II with spinal ONTD in a late-stage chick embryo model with MRI and histopathological analysis. The morphological changes of the posterior fossa in this study mimic those of CM II associated with spinal ONTD in humans. This model will facilitate investigation of the pathogenesis of CM II.