• 대한전기학회논문지:전기기기및에너지변환시스템부문B
• /
• 제53권3호
• /
• pp.143-151
• /
• 2004

High-speed permanent magnet machines are likely to be a key technology for electric drives and motion control systems for many applications, since they are conductive to high efficiency, high power density, small size and low weight. In high-speed machines, the permanent magnets are often contained within a retaining sleeve. However, the sleeve and the magnets are exposed to high order flux harmonics, which cause parasitic eddy current losses. Rotor losses of high-speed machines are of great importance especially in high-speed applications, because losses heat the rotor, which is often very compact construction and thereby difficult to cool. This causes a danger of demagnetization of the NdFeB permanent magnets. Therefore, special attention should be paid to the prediction of the rotor losses. This paper is concerned with the rotor losses in permanent magnet high-speed machines that are caused by permeance variation due to stator slotting. First, the flux harmonics are determined by double Fourier analysis of the normal flux density data over the rotor surface. And then, the rectilinear model was used to calculate rotor losses in permanent magnet machines. Finally, Poynting vector have been used to investigate the rotor eddy current losses of high-speed Permanent magnet machine.

• 조명전기설비학회논문지
• /
• 제28권12호
• /
• pp.95-102
• /
• 2014

This paper proposes a coordinated control for an independent multi-phase transverse flux linear synchronous motor (IM-TFLSM) based on magnetic levitation. The stator structures of the IM-TFLSM are composed of a two set, which has independent three-phase windings and a double-sided air-gap as opposed to the conventional Y-connected three-phase linear motors. A suitable control algorithm is necessary to operate the applied linear machine. This study proposes a coordinated control algorithm for adjusting the mover air-gap and thrust force of the IM-TFLSM in order to maintain air-gap and phase shifted current control of the independent 3-phase modules. In addition, the principle of operation and its special structures are described in detail and the validity and effectiveness of the control algorithm is verified through multiple experimental results.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2003년도 하계학술대회 논문집 B
• /
• pp.735-737
• /
• 2003

A superconducting motor consisting of high temperature superconducting (HTS) rotor and air-core stator is under development in Korea Electrotechnology Research Institute. HTS motor was designed for having the rated power of 100hp at 1800 rpm. HTS field winding is composed of sixteen HTS race track shaped coils wound with stainless steel-reinforced Bi-2223 tape conductor by react and wind fabrication method. Nomex Paper was used for electrical insulation. Each of four magnet pole assemblies was constructed with four double pancake sub-coils, mechanically stacked and electrically in series. Four magnet assemblies were fixed on an aluminum support structure to make effective heat transfer. Critical current (Ic) of HTS field winding was 41A but minimum Ic of sub-coils was 35A at 77K and self field. Joule heat generated in HTS field winding was 2.11W at 77K and 35A.

• Journal of Power Electronics
• /
• 제15권2호
• /
• pp.411-418
• /
• 2015

In this paper, a new method for the online estimation of equivalent series resistances (ESR) of the DC-link capacitors in induction machine (IM) drive systems with a front-end diode rectifier is proposed, where the ESR estimation is conducted during the regenerative operating mode of the induction machine. In the first place, a regulated AC current component is injected into the q-axis current component of the induction machine, which induces the current and voltage ripple components in the DC-link. By processing these AC signals through digital filters, the ESR can be estimated by a recursive least squares (RLS) algorithm. To acquire the AC voltage across the ESR, the DC-link voltage needs to be measured at a double sampling frequency. In addition, the ESR current is simply reconstructed from the stator currents and switching states of the inverter. Experimental results have shown that the estimation error of the ESR is about 1.2%, which is quite acceptable for condition monitoring of the capacitor.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2007년도 제38회 하계학술대회
• /
• pp.361-363
• /
• 2007

In this paper, an auto-diagnosis method of rotor bar fault for small induction motor is suggested. Usually FFT of stator currents are given the good results, but to detect the fault, slip is needed for calculating the feature frequency. The slip is varied as the load is changed. So in this paper, some alternative method for estimating the load is suggested. This method is based on the Park's vector pattern. The magnitudes of the feature frequency are compared with the threshhold that is predefined in the bounded range of load. The healthy rotor, single rotor bar fault and double rotor bar fault are tested with no load, 25%, 50%, 75%, and 100% rated load. From 50% to 100% rated load case, the rotor bar faults are detectable using indirect estimation of the load and the comparing the magnitudes of feature frequency. The no load case and under 40% rated load case, rotor fault are un detectable.

• 전력전자학회논문지
• /
• 제6권2호
• /
• pp.202-208
• /
• 2001

스위치드 리럭턴스 모터(Switched Relutance Motor : 이하 SRM)는 이중 돌극형으로 되어있으며, 상권선은 고정자만 사용한다. 다른 어느 전동기보다도 간단한 구조를 가지고 있어 제작단가가 저렴하고, 기계적으로 견고하며, 고온 등의 열악한 환경에서도 신뢰성이 높으며, 브러쉬 등이 없어 유지비가 거의 들지 않는 장점을 지니고 있다. 그러나 SRM은 상여자를 위하여 회전자의 위치정보를 알아야하므로 위치 검출기가 필요하고, 정속도 운전을 위하여 타코 발전기나 엔코더가 부가적으로 필요하다. 그러나 본 논문에서는 회전자의 속도측정을 얻기 위하여 고가의 엔코더를 사용하지 않고, 단지 간단한 슬롯 디스크로부터 위치를 검출하여 속도를 추정할 수 있는 알고리즘을 제시하고 개발하였다. 속도 추정 알고리즘을 적용한 가변속 디지털 제어시스템을 구현하기 위하여 TI사의 TMS320F240-20MIPS 고정 소수점 연산용 프로세서를 사용하였다. 개발한 시스템을 실험한 결과 넓은 범위에 걸쳐 속도제어가 가능하였고, 단일 펄스모드, 하드 쵸핑모드 및 소프트 쵸핑모드 뿐만 아니라, 전류제어 동작모드에서 가변속 제어가 가능하였다. 그리고 어드밴스각 제어가 가능하였다.

• 대한조선학회논문집
• /
• 제53권5호
• /
• pp.343-352
• /
• 2016

In this study, a pre-swirl duct for the 180,000 DWT bulk carrier has been designed from a propulsion standpoint using CFD. The stern duct - designed by NMRI - was selected as the initial duct. The objective function is to minimize the value of delivered power in model scale. Design variables of the duct include duct angle, diameter, chord length, and vertical and horizontal displacements from the center. Design variables of the stators are blade number, arrangement angle, chord length, and pitch angle. A parametric design was carried out with the objective function obtained using CFD. Reynolds averaged Navier-Stokes equations have been solved; and the Reynolds stress model applied for the turbulent closure. A double body model is used for the treatment of free-surface. MRF and sliding mesh models have been applied to simulate the actuating propeller. A self-propulsion point has been obtained from the results of towing and self-propelled computations, i.e., form factor obtained from towing computation and towing forces obtained from self-propelled computations of two propeller rotating speeds. The reduction rate of the delivered power of the improved stern duct is 2.9%, whereas that of the initial stern duct is 1.3%. The pre-swirl duct with one inner stator in upper starboard and three outer stators in portside has been designed. The delivered power due to the designed pre-swirl duct is reduced by 5.8%.

• 한국자기학회지
• /
• 제26권1호
• /
• pp.31-37
• /
• 2016

본 논문은 파력에너지 변환용 양측식 슬롯티드 타입 선형 발전기의 디텐트력 저감을 위한 방법을 제시하였다. 양측식 선형 발전기는 비교적 큰 공극을 갖는다. 그렇기 때문에 일반적으로 선형기는 슬롯 구조를 갖는다. 이때의 디텐트력은 선형 발전기의 치/슬롯과 영구자석 사이에 발생하는 힘으로 불필요한 에너지원으로 작용한다. 따라서, 본 논문에서는 슬롯구조를 갖는 선형 기기의 디텐트력을 줄이기 위한 세가지 방법인 보조치, 노치적용을 제시하고 유한요소해석법을 이용하여 본 연구의 타당성을 입증하였다.