• 한국추진공학회지
• /
• 제25권3호
• /
• pp.42-55
• /
• 2021

본 연구에서는 중심선 방정식 선정에 따른 노즐 성능 영향성을 확인하고자 하였다. 곡선 방정식과 설계 형상 파라미터를 활용하여 S-형 노즐 3조와 Double S-형 노즐 3조를 설계하였고 노즐 차폐 성능은 차폐율 정의를 이용하여 평가하였다. 그리고 내부 유동을 분석하기 위해 속도 분포도와 압력분포도로 특성을 연구하였고, 노즐 성능 계수로는 총 추력 비(f)와 노즐 단열 효율계수(η)를 통해 노즐의 성능을 평가하였다. 중심선에 따른 S-형 노즐의 성능 영향성을 분석한 결과 출구에서 급격한 곡률 변화가 있는 중심선은 노즐 성능이 우수한 반면 차폐율이 낮은 특징이 있다. 반면에 입구에서 급격한 곡률 변화가 있는 중심선은 노즐 성능이 낮아지고 차폐율이 높은 특징이 있다. Double S-형 노즐은 첫 번째 곡률에서 완만한 특징을 보이는 중심선을 사용하는 것이 노즐 성능과 차폐율이 우수하였다.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2001년도 추계학술대회논문집A
• /
• pp.400-405
• /
• 2001

Nozzle of the double-plated grid plays the role of the spring to support a fuel rod as well as to provide the coolant path in grid. The nozzle was known to be necessary to reduce the spring stiffness for supporting performance. In this study the contact analysis between the fuel rod and the nozzle type spacer grid was performed by using ABAQUS standard to propose the preferable shape in tenn of spring performance. Two small cuts at the upper and lower part of the nozzle appeared to have a minor effect in decreasing the nozzle stiffness. A long slot at the center of the nozzle was turned out not only to decrease the spring constant as desired but also to increase the elastic displacement.

• 한국전산유체공학회:학술대회논문집
• /
• 한국전산유체공학회 1998년도 춘계 학술대회논문집
• /
• pp.168-173
• /
• 1998

A numerical analysis of axisymetric backward facing step main nozzle flow in air jet loom has been accomplished. To obtain basic design data for an optimum main nozzle for an air-jet loom and to predict the transonic/supersonic flow, a characteristic based upwind flux difference splitting compressible Navier-Stokes method has been used. The wall static pressure of the main nozzle and the flow velocity changes in the nozzle tube were analyzed by changing air tank pressures and acceleration tube lengths. The flow inside the nozzle experiences double choking one at the needle tip and the other at the acceleration tube exit at tank pressures over $4kg_f/cm^2$. The tank pressure $P_t$ leading to the critical condition depends on the acceleration tube length; i.e, $P_t$ is higher for longer acceleration tubes. The $P_t$ value required to bring the acceleration tube exit to the critical condition is nearly constant regardless of acceleration tube length. The round needle tip shape might lead to less total pressure loss when compared with step shape.

• 한국진공학회:학술대회논문집
• /
• 한국진공학회 2011년도 제40회 동계학술대회 초록집
• /
• pp.159-159
• /
• 2011

Among the semiconductor ternary compounds in the I-III-$VI_2$ series, $CulnS_2$ ($CulnSe_2$) are one of the promising materials for photovoltaic applications because of the suitability of their electrical and optical properties. The $CuInS_2$ thin film is one of I-III-$VI_2$ type semiconductors, which crystallizes in the chalcopyrite structure. Its direct band gap of 1.5 eV, high absorption coefficient and environmental viewpoint that $CuInS_2$ does not contain any toxic constituents make it suitable for terrestrial photovoltaic applications. A variety of techniques have been applied to deposit $CuInS_2$ thin films, such as single/double source evaporation, coevaporation, rf sputtering, chemical vapor deposition and chemical spray pyrolysis. This is the first report that $CuInS_2$ thin films have been prepared by Aerosol Jet Deposition (AJD) technique which is a novel and attractive method because thin films with high deposition rate can be grown at very low cost. In this study, $CuInS_2$ thin films have been prepared by Aerosol Jet Deposition (AJD) method which employs a nozzle expansion. The mixed fluid is expanded through the nozzle into the chamber evacuated in a lower pressure to deposit $CuInS_2$ films on Mo coated glass substrate. In this AJD system, the characteristics of $CuInS_2$ films are dependent on various deposition parameters, such as compositional ratio of precursor solution, flow rate of carrier gas, stagnation pressure, substrate temperature, nozzle shape, nozzle size and chamber pressure, etc. In this report, $CuInS_2$ thin films are deposited using the deposition parameters such as the compositional ratio of the precursor solution and the substrate temperature. The deposited $CuInS_2$ thin films will be analyzed in terms of deposition rate, crystal structure, and optical properties.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2002년도 학술대회지
• /
• pp.155-158
• /
• 2002

In general, TVC(Thermal Vapor Compressor) is used to boost/compress a low pressure vapor to a higher pressure for further utilization. The one-dimensional method is simple and reasonably accurate, but cannot realize the detail as like the back flow and recirculation in the mixing chamber, viscous shear effect, and etc. In this study, the axisymmetric How simulations have been performed to reveal the detailed flow characteristics for the various ejector shapes. The Navier-Stokes and energy equations are solved together with the continuity equation In the compressible flow fields. The standard $k-{\epsilon}$ model is selected for the turbulence modeling. The commercial computational fluid dynamic code FLUENT software is used for the simulation. The results contain the entrainment ratio under the various motive, suction and discharge pressure conditions. The numerical results are compared with the experimental data, and the comparison shows the good agreement. The three different flow regimes (double chocking, single chocking and back flow) have been clearly distinguished according to each boundary pressure values. Also the effects of the various shape variables (nozzle position, nozzle outlet diameter, mixing tube diameter, mixing tube converging angle, and etc.) are quantitatively discussed.

• 대한기계학회논문집
• /
• 제9권6호
• /
• pp.732-742
• /
• 1985

본 논문에서는 이 2차원 재부착분류(본문에서는 stepped wall jet라 명명함) 유동장을 재부착상류 부분, 재부착점 근방, 재부착 이후의 재발전 벽면분류 지역의 세 영역으로 구분하여 재부착 길이, 평균속도, 벽면정압을 측정하고 on-line에 의한 디지 틀 데이터 처리기법을 이용하여 난류강도, 레이놀즈 전단응력, 속도의 3승적(triple velocity product), integral length scale, Taylor's microscale 등을 실험적으로 구 하여 재부착 상류 부분에서는 자유분류와 비교하고, 재부착 이후에서는 2차원 벽면분 류와 비교하기로 한다.그리하여 초기 교란을 받는 분류가 벽면에 재부착하여 2차원 벽면분류로 재발전되어 가는 과정에 있어서의 평균 유동장과 급격한 변화를 갖는 난류 특성을 상세히 조사하여, 보다 일반적으로 적용될 수 있는 난류모델을 개발함에 있어 서 실험적인 자료를 제공하고자 한다. Fig. 1은 본 실험의 유동장에 대한 개약도를 보여주고 있다.