• Journal of Electrical Engineering and Technology
• /
• v.3 no.1
• /
• pp.20-28
• /
• 2008

This paper proposes a method for solving distribution system planning problems taking into account demand uncertainty and geographical information. The proposed method can automatically select appropriate location and size of a substation, routing of feeders, and appropriate sizes of conductors while satisfying constraints, e.g. voltage drop and thermal limit. The demand uncertainty representing load growth is modeled by fuzzy numbers. Feeder routing is determined with consideration of existing infrastructure, e.g. streets and canals. The method integrates planner's experience and process optimization to achieve an appropriate practical solution. The proposed method has been tested with an actual distribution system, from which the results indicate that it can provide satisfactory plans.

• Proceedings of the Korean Society of Agricultural Engineers Conference
• /
• 2005.10a
• /
• pp.247-253
• /
• 2005

In this stydy, the characteristics of the spatial location based on rural environment pollution facilities which can cause environmental pollution and thus lower the value of rural amenity was analyzed. This study showed that livestock feedlot occupied the highest percentage among the facilities analyzed and the size of facilities increased with increasing distance from the residential area. In addition, the facilities showed two typical characteristics in terms of their spatial distribution; uneven and even distribution which are characterized by concentrated distribution in a certain area and by scattered distribution in a wide area, respectively. As the facilities including livestock feedlot have a great potential to cause environmental problem such as air, water, soil and noise pollution, it is necessary to develop systematic plans for the management and improvement of the facilities.

• Journal of Applied Reliability
• /
• v.13 no.2
• /
• pp.87-98
• /
• 2013

Accelerated degradation tests (ADTs) measuring failure-related degradation characteristic at the accelerated condition are widely used to assess the reliability of highly reliable products. Often, however, little degradation could be observed even in single-stress ADTs due to the high reliability of test unit, and as a result poor estimate of the reliability may be obtained. ADTs with multiple stress variables can be employed to overcome such difficulties. In this paper, optimal ADT plans with two stress variables are developed assuming that the degradation characteristic follows Weibull distribution by determining the stress levels, the proportion of test units allocated to each stress level such that the asymptotic variance of the maximum likelihood estimator of the q-th quantile of the lifetime distribution at the use condition is minimized.

• The Journal of Asian Finance, Economics and Business
• /
• v.7 no.6
• /
• pp.509-515
• /
• 2020

TThe cooperation on disaster prevention between the two Koreas has been mostly focused on cooperation at the recovery stage, such as emergency relief supplies and equipment support. This study aims to articulate future practical development plans by analyzing disaster cooperation between North and South Korea in accordance with the changing paradigm of international disaster cooperation. Considering the specificity of inter-Korean cooperation, the Framework for Inter-Korean Disaster Prevention Cooperation was established centering on the Sendai Framework for Disaster Risk Reduction. The framework consists of understanding and sharing disaster risks, building back better, strengthening community resilience, and supporting regional disaster action plans for continuous action. Inter-Korean disaster prevention cooperation requires sharing information about North Korean disasters. It is necessary to accurately identify and support social vulnerability to North Korean disasters. Above all, it is supporting the development of disaster action plans from a humanitarian perspective needs. A medium-to-long term resilience reinforcement plan that North Korea can resolve on its own is also needed. Since North Korea is also deeply interested in international disaster cooperation, it should be based on the direction of the Sendai Framework. Considering the uniqueness of inter-Korean cooperation, a path for North Korea to actively participate in international disaster cooperation should be established.

• Korean Institute of Interior Design Journal
• /
• v.16 no.6
• /
• pp.205-212
• /
• 2007

It is a world wide tread for museums to become specialized museums emphasizing their characteristics, but Seongbo museums(museums that preserve Buddhist artifacts) are more general and show no specialization or characterization. The purpose of this study is to emphasize the special character of the Seongbo museum which manages and maintains sacred Buddhist cultural artifacts, and to understand the architectural characteristics of the building distribution and interior composition to implement a more systematic spatial composition plan. For our analysis we selected 6 currently operating museums as our subjects, and analyzed the characteristics of their spatial composition through their plans including the plot plans and ground plans. As a result, we found that most of them were small scale museums, and that the character and rank of each building changed according to its positioning. In terms of areas, the museums consisted of exhibition areas, storage areas, maintenance areas, and other miscellaneous areas and were lacking areas for research and education. It is necessary for these museums to possess facilities for managing these cultural artifacts as well as adequate exhibition and storage spaces. Seongbo museums, which are connected with Buddhist temples, must possess differentiated preservation and maintenance methods unlike museums dealing with artifacts that need only be preserved, and must have an area plan suitable to the characteristics of the various artifacts near and around the temple so as to help build our Buddhist cultural heritage in a systematic and continuous matter.

• Journal of the Korean Society for Precision Engineering
• /
• v.16 no.11
• /
• pp.22-35
• /
• 1999

The block assembly process takes more than half of the total shipbuilding processes. Therefore, it is very important to have a practically useful block assembly process planning system which can build plans of maximum efficiency with minimum man-hours required. However, the process plans are often not readily executable in the assembly shops due to severe imbalance of workloads. This problem arises because the process planning is done on block by block basis in current practice without paying any attention to the load distribution among the assembly shops. this paper presents the development of an automated hull block assembly process planning system which results in the most effective use of production resources and also produces plans that enable efficient time management. If the load balance of assembly shops is to be considered at the time of process planning, the task becomes complicated because of the increased computational complexity. To solve this problem, a new approach is adopted in this research in which the load balancing function and process planning function are iterated alternately providing to each other contexts for subsequent improvement. The result of case study with the data supplied from the shipyard shows that the system developed in this research is very effective and useful.

• Journal of Korean Society of Industrial and Systems Engineering
• /
• v.41 no.2
• /
• pp.117-132
• /
• 2018

There always exist nonzero inspection errors whether inspectors are humans or automatic inspection machines. Inspection errors can be categorized by two types, type I error and type II error, and they can be regarded as either a constant or a random variable. Under the assumption that two types of random inspection errors are distributed with the "uniform" distribution on a half-open interval starting from zero, it was proved that inspectors overestimate any given fraction defective with the probability more than 50%, if and only if the given fraction defective is smaller than a critical value, which depends upon only the ratio of a type II error over a type I error. In addition, it was also proved that the probability of overestimation approaches one hundred percent as a given fraction defective approaches zero. If these critical phenomena hold true for any error distribution, then it might have great economic impact on commercial inspection plans due to the unfair overestimation and the recent trend of decreasing fraction defectives in industry. In this paper, we deal with the same overestimation problem, but assume a "symmetrical triangular" distribution expecting better results since our triangular distribution is closer to a normal distribution than the uniform distribution. It turns out that the overestimation phenomenon still holds true even for the triangular error distribution.

• Progress in Medical Physics
• /
• v.23 no.2
• /
• pp.99-105
• /
• 2012

We investigated the influence of photon energy, couch and collimator angle differences between arcs on dose distribution of RapidArc treatment planning for prostate cancer. RapidArc plans were created for 6 MV and 10 MV photons using 2 arcs coplanar and noncoplanar fields. The collimator angle differences between two arcs were $0^{\circ}$, $15^{\circ}$, $30^{\circ}$, $45^{\circ}$, $60^{\circ}$, $75^{\circ}$ and $90^{\circ}$. The plans were optimized using same dose constrains for target and OAR (organ at risk). To evaluate the dose distribution, plans were analyzed using CI (conformity index), HI (homogeneity index), QOC (quality of coverage), etc. Photon energy, couch and collimator angle differences between arcs had a little influence on the target and OAR. The difference of dosimetric indices was less than 3.6% in the target and OAR. However, there was significant increase in the region exposed to low dose. The increase of V15% in the femur was 6.4% (left) and 5.5% (right) for the 6 MV treatment plan and 23.4% (left), 24.1% (right) for the noncoplanar plan. The increase of V10% in the Far Region distant from target was 54.2 cc for the 6 MV photon energy, 343.4 cc for the noncoplanar and 457.8 cc for the no collimator rotation between arcs.

• Journal of Distribution Science
• /
• v.13 no.6
• /
• pp.79-86
• /
• 2015

Purpose - The cosmetics industry is a traditional high value-added industry in terms of the domestic demand, small batch production systems, exclusive competition, and raw materials highly dependent on overseas countries as well as an oligopolistic market structure. However, new foreign brands and growing consumer awareness of inexpensive products, has triggered a shift. In line with changing lifestyles and the polarization of consumption, the industry faces a new market structure. Among its key characteristics is the cosmetics industry's numerous distribution channels (i.e., department stores, door-to-door sales, online shopping malls, brand shops, and discount stores). Therefore, the study of its distribution channels is essential. Research design, data, and methodology - The study analyzed channel distribution power divided into coercive and non-coercive power. The factors of coercive power included: unilateral request of an increase in commissions, interference in sales by taking advantage of a superior status, unilateral buck-passing at the time of a problem, unilateral request to stop sales activities, and a unilateral business contract; the factors of non-coercive power included favorable payment conditions, offers of various kinds of information, policy on commission reduction, pride in market entrance, and promotion support. In addition, the mediating variable "interdependence" was applied to the execution of department store (or mart) power and their shop conflicts and satisfaction to examine direct and indirect influential power. The methodology was a survey of managers of cosmetics shops in department stores (or marts). The questionnaire, based on a five-point Likert scale, included questions about basic personal information, execution of power, interdependence, conflict, and satisfaction. The study distributed 198 questionnaires and collected 131. Ten questionnaires with missing or hard to analyze data were excluded. Thus, 121 copies were analyzed. Results - According to the analysis, the execution of coercive power by department stores (or marts) did not affect interdependence, but the execution of non-coercive power did. Interdependence did not influence conflict, but did affect satisfaction. Additionally, the analysis revealed direct influential power: the execution of coercive power positively affected conflict and negatively influenced satisfaction; the execution of non-coercive power positively affected satisfaction. Conclusions - To offer suggestions for distribution business relations in the cosmetics industry, this study investigated how the execution of power by department stores (or marts) affected their shops. More specifically, it examined how much the execution of both coercive power and non-coercive power influenced conflict and satisfaction, and analyzed the mediating role of interdependence. In line with previous study results in various areas, coercive power was shown to be the source of conflict, leading to a decrease in satisfaction, whereas non-coercive power significantly positively influenced satisfaction. Moreover, non-coercive power increased interdependence, which led to greater satisfaction. As a result, interdependence had a mediating effect on non-coercive power and satisfaction. Based on the results, department stores (or marts) should look for improvements plans that increase interdependence. Such plans could alleviate conflict with the shops, increasing their satisfaction.

• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.24 no.7
• /
• pp.20-25
• /
• 2010

With the diversification of distribution facilities, existing distributed generation can be subdivided into Microgrids, which are smaller units for application. These Microgrids, subdivided as such and connected to distribution systems, should operate under driving plans that will ensure their economic efficiency and, accordingly, the configuration of those distribution systems that include Microgrids should also be changed. The perception of the necessity to secure the economic efficiency of distribution systems is gradually increasing and studies intended to assess the economic efficiency of Microgrids and Smartgrids are ongoing. In this paper, the power generation capacity of an economically operative Microgrid was calculated using the MonteCarlo simulation, which is a method based on the probability theory considering the power generation cost of Microgrids linked with power supply systems and reverse sales costs, etc., and an optimum distribution systems was configured based on the results of these calculation.