• 대한전기학회:학술대회논문집
• /
• 대한전기학회 1997년도 추계학술대회 논문집 학회본부
• /
• pp.581-583
• /
• 1997

In this paper, we present a temperature characteristic in OPGW link due to meteological effects. we measured a temperature on a 2km OPGW using a distributed optical fiber temperature sensing system. The measurement showed that OPGW temperature was several degrees lower to ambient atmospheric temperature in the nighttime and several degrees higher than that in the daytime due to sunshine. It'll be used for a reference data of the transmission delay variations in OPGW link due to meteorological effects.

• 한국신재생에너지학회:학술대회논문집
• /
• 한국신재생에너지학회 2006년도 춘계학술대회
• /
• pp.451-454
• /
• 2006

Fiber optic distributed temperature sensing and thermal line sensor are applied in an observation borehole and a loom deep borehole heat exchanger. For the case of permanently installed system fiber optic DTS is very useful. By comparing with TLS, fiber optic DTS shows good accuracy and reliability. Ground water flow can give influences at heat exchange rate of the heat pump system. According to the hydraulic characteristics and temperature-depth profile, we consider that temperature-depth profile do not seem to be dependent on ground water flow. A permanent installation of fiber optic cable is expected as a reliable temperature measurement technique in a borehole heat exchanger system.

• 대한토목학회논문집
• /
• 제33권6호
• /
• pp.2237-2244
• /
• 2013

본 연구에서는 GIS 공간 수문자료를 입력 자료로 활용하는 물리적기반의 분포형 강우유출모형(K-DRUM, K-water Distributed RUnoff Model)을 고도분포에 따른 기온변화와 융 적설 모의가 가능하도록 확장 개발하여 파키스탄 Kunhar강 유역($2,500km^2$)을 대상으로 융 적설을 고려한 장기 유출량 모의결과를 비교 분석하였다. 기온 및 강우 시계열 자료 분석 결과 동일한 유역 내 표고에 따른 기온 및 강우차가 국내유역과는 달리 매우 심하게 나타나 기온 및 고도감율을 적용하여 모형의 입력값으로 산정하였다. 해발고도 4,000m차이의 융 적설 특성을 반영한 유출량 재현성은 비교적 양호하였으며, 연중 유출패턴은 여름철 기온상승에 의해 융설로 인한 유출이 강하게 나타나고 있었다.

• The Korean Journal of Ecology
• /
• 제17권4호
• /
• pp.485-499
• /
• 1994

This study was focused on the effect of the altitude on the geographical variations of germination characteristics in the populations of Plantago asiatica L. distribute in Mt. Chiri. There was a significant difference among the 14 groups in the phenological pattern in relation to altitudes. When the altitude becomes higher, the thermal time which was required for 10 to 80% germination rate showed higher and wider distribution. On the other hand, the germination response of increasing temperature (IT) and secreasing temperature (DT) regime was classified into 3 group. The first group was the spering germination type. This group showed that the IT regime hadhigher germination rate than that of the DT regime, and was distributed in Macheon(300m) and Packmudong (500m). The second was the spring-fall germination type which was distributed in Hadong (900m) and Saemt대 (1100m). This group also showed higher germination rate in the IT regime, but the difference of the germination rate between IT and DT regime was less than that in the first group (the spring type). The third group was the early fall germination type which was found in the Nogodan (1507m), Changetomok (1750m) and Cheonwangbong (1915m). The germination rate of this group showed almost 100% similarity between IT and DT regime. These data suggested that the geographical varations of germination characteristics within species was an important ecological strategy for the survival from severe environmental conditions.

• 한국안전학회지
• /
• 제32권2호
• /
• pp.46-51
• /
• 2017

This paper presents classification of domestic fire detector using response time index. Response time is measured using fire detector distributed in Korea, and the response time index is estimated. Plunge test prescribed by FM is conducted to measure response time of fire detector. The detector used to test is fixed temperature type(thermistor and bimetal type) and rate of rise temperature type(thermistor and pneumatic type). The nominal operation temperature of fixed temperature type detector is $70^{\circ}C$ and rate of rise temperature is $15^{\circ}C/min$. The fixed temperature type is measured 7 products, and the rate of rise temperature type is measured 5 products. The results show that in case of fixed temperature type(thermistor) is classified "Quick" or "Standard" and fixed temperature type(bimetal) is not classified. The rate of rise temperature type(thermistor) is classified "Fast" or "Ultra Fast" and the rate of rise temperature type(pneumatic) is classified "Very Fast" or "Ultra Fast". The pneumatic type shows more fast response than thermistor type. Also these results indicate the fixed temperature type(bimetal) is not suitable for early stage fire detection.

• The Korean Journal of Ecology
• /
• 제19권5호
• /
• pp.453-463
• /
• 1996

Diurnal changes of microclimatic conditions and tissue water relations were measured at two sites where Carpinus laxiflora and C. cordata were allopatrically distributed. The microclimatic conditions at a site where C. laxiflora was distributed produced severe water stress condition during summer months. Daily maximum temperature reached $30.4^\circC$ and the highest vapor pressure deficit was 1.31 KPa when 13 rainless days were continued. During this period soil water content decreased to below the field capacity even at a depth of 20 cm and xylem pressure potential also decreased to ­2.04 MPa. However, turgor potential was maintained more than 0.4 MPa. Patterns of stomatal conductance were changed with evaporative demand and soil water availability. On the other hand, microclimatic conditions at a site where C. cordata was distributed were moderate water strees condition compared with those at a site C. laxiflora was distributed. Though soil water content was maintained above field capacity C. cordata showed a remarkable decrease in turgor potential and stomatal conductance throughout the experiment. These results indicate that there is a difference in habitat characteristics between the two species and C. laxiflora is more resistant than C. cordata to water stress.

• 한국추진공학회:학술대회논문집
• /
• 한국추진공학회 2017년도 제48회 춘계학술대회논문집
• /
• pp.1127-1134
• /
• 2017

가스터빈 엔진 제어기는 과거의 유압기계식 조절기에서 유래하였고 1970년대의 DEEC를 거쳐 현대의 중앙집중식 FADEC에 이르고 있다. 제어성능의 향상, PHM 기술의 접목, 무게 절감의 목표를 달성하기 위해서는 분산엔진제어 시스템으로의 이행이 필요하다. 본 논문에서는 분산제어시스템의 개념 및 기술 발전 동향, 시스템의 성공적인 개발을 위한 정부-기업 간의 노력, 그리고 향후 극복해야 할 과제에 대하여 기술하였다.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 1991년도 추계학술대회 논문집 학회본부
• /
• pp.386-389
• /
• 1991

The problem of constructing an bilinear observer for use in the control of superheater temperature with desuperheater is considered. The distributed heat input into the superheater is usually not available for use in the observer, and hence is treated as an unknown inputs. The bilinear observer theory for system with unknown inputs is exploited and applied to the problem.

• 제어로봇시스템학회:학술대회논문집
• /
• 제어로봇시스템학회 1990년도 한국자동제어학술회의논문집(국내학술편); KOEX, Seoul; 26-27 Oct. 1990
• /
• pp.101-106
• /
• 1990

The problem of constructing an observer for use in the control of superheater temperature with desuperheater is considered. The distributed heat input into the superheater is usually not available for use in the observer, and hence is treated as a disturbance. The observer theory for systems with unknown inputs is exploited and applied to the problem. Approximation of the heat input utilizing the specific heat input distribution pattern is also considered.

• 제어로봇시스템학회:학술대회논문집
• /
• 제어로봇시스템학회 2004년도 ICCAS
• /
• pp.863-868
• /
• 2004

Reheating furnace is an essential facility of a rod mill plant where a billet is heated to the required rolling temperature so that it can be milled to produce wire. Sometimes, it is also necessary to control a transient billet temperature pattern according to the material characteristics to prevent a wire from breaking. Though it is very important objective to obtain a correct information of a billet temperature during furnace operation. Consequently, a billet temperature profile must be estimated. In this paper, a billet heat transfer model based on FEM (Finite Element Method) with spatially distributed emission factors is proposed and a measurement is also carried out for two different furnace operation conditions. Finally, the difference between the model outputs and the measurements is minimized by using the new optimization algorithm named uDEAS(Univariate Dynamic Encoding Algorithm for Searches) with multi-step tuning strategy. Hence, the information of billet temperatures can be obtained by using proposed model on various furnace operation conditions.