• Journal of KIISE:Information Networking
• /
• v.32 no.3
• /
• pp.370-381
• /
• 2005

Mobile IP provides an efficient and scalable mechanism for host mobility within the Internet. Using Mobile If, mobile nodes may change their point of attachment to the Internet without changing their If address. However, it would result in a high signaling cost. To reduce the signaling cost, we factor in the fact that mobile users will not be actively communicating much of the time. In fact, there Is no necessity to send a binding update message to the home agent when an mobile node does not communicates with others while moving. From this point of view, we propose a lazy update strategy for minimizing signaling cost using the forwarding pointer in hierarchical Mobile IPv6. In our proposal, binding updates are sent only when a mobile node is in a busy mode. If an mobile node is in a dormant mode, binding update messages are delayed until busy mode using the forwarding pointer. As a result, our proposal can reduce the total signaling cost by eliminating unnecessary binding update messages when a mobile node Is in a dormant mode. In addition to, our proposal reduces unnecessary location update cost resulting from ping-pong effect under mobile node's dormant mode. Analysis results using the discrete analytic model presented in this paper shows that our proposal can has superior performance than hierarchical Mobile nv6 when the call-to-mobility ratio is low and the length of the forwarding pointer chain K is low.

• Journal of the Korean Geotechnical Society
• /
• v.30 no.7
• /
• pp.41-53
• /
• 2014

This study examined the magnitude and distribution of the earth pressure on the support system in a jointed rock mass by considering different joint shear strength, rock type, and joint inclination angle. The study particularly focused on the effect of joint cohesive strength for a certain condition. Based on a physical model test (Son and Park, 2014), extended parametric studies were conducted considering rock-structure interactions based on the discrete element method, which can consider the rock and joint characteristics of rock mass. The results showed the earth pressure was strongly affected by the joint cohesive strength as well as the rock type and joint inclination angle. The study indicated that the effect of joint cohesive strength was particularly significant when a rock mass was under the condition of joint sliding. This paper investigates the magnitude of joint cohesive strength to prevent a joint sliding for each different condition. The test results were also compared with Peck's earth pressure, which has been frequently used for soil ground. The comparison indicated that the earth pressure in a jointed rock mass can be significantly different from that in soil ground. This study is expected to provide a better understanding of the earth pressure on the support system in a jointed rock mass.

• Genomics & Informatics
• /
• v.8 no.3
• /
• pp.108-115
• /
• 2010

Hypertension is the most prevalent disease worldwide and is itself a risk factor for cerebral, cardiac, and renal diseases. The inconsistency of candidate genes suggested by previous genomewide association studies (GWASs) may be due to not only differences in study design and genetic or environmental background but also the difference in the power of analysis between continuous traits and discrete traits. We analyzed 352,228 single nucleotide polymorphisms (SNPs) in 8842 unrelated Koreans obtained from Ansan and Ansung cohorts. We performed a series of GWA analyses using three different phenotype models; young hypertensive cases (278 subjects) versus elderly normotensive controls (680 subjects); the upper 25% (2211 hypertensive cases) versus the lower 25% of the SBP distribution (2211 hypotensive controls); and finally SBP and DBP as continuous traits (8842 subjects). The numbers of young hypertensive cases and elderly normotensive controls were not large enough to achieve genomewide significance. The model comparing the upper 25% subjects to the lower 25% of subjects showed a power that was approximate to that of QTL analysis. Two neighboring SNPs of the ATP2B1 gene, rs17249754 (SBP, p=$2.53^{-10}$; DBP, p=$1.28{\times}10^{-8}$) and rs7136259 (SBP, p=$1.30{\times}10^{-9}$; DBP, p=$6.41{\times}10^{-8}$), were associated with both SBP and DBP. Interestingly, a SNP of the RPL6 gene, rs11066280, revealed a significant genomewide association with SBP in men only (p=$3.85{\times}10^{-8}$), and four SNPs located near the MAN2A1 gene showed a strong association with DBP only in elderly men aged 60-70 years (e.g., rs6421827, p=$4.86{\times}10^{-8}$). However, we did not observe any gene variant attaining genomewide significance consistently in the three phenotype models except for the ATP2B1 gene variants. In general, the association signal with blood pressure was stronger in women than in men. Genes identified in GWASs are expected to open the way for prevention, early diagnosis, and personalized treatment of hypertension.

• The KIPS Transactions:PartB
• /
• v.9B no.5
• /
• pp.663-672
• /
• 2002

In this paper, Using an automatic tracking system, behavior of an aquatic insect, Chironomus sp. (Chironomidae), was observed in semi-natural conditions in response to sub-lethal treament of a carbamate insecticide, carbofuran. The fourth instar larvae were placed in an observation cage $(6cm\times{7cm}\times{2.5cm)}$ at temperature of $18^\circ{C}$ and the light condition of 10 time (light) : 14 time (dark). The tracking system was devised to detect the instant, partial movement of the insect body. Individual movement was traced after the treatment of carbofuran (0.1ppm) for four days 2days : before treatment, 2 days : after treatment). Along with the other irregular behaviors, "ventilation activity", appearing as a shape of "compressed zig-zag", was more frequently observed after the treatment of the insecticide. The activity of the test individuals was also generally depressed after the chemical treatment. In order to detect behavioral changes of the treated specimens, wavelet analysis was implemented to characterize different movement patterns. The extracted parameters based on Discrete Wavelet Transforms (DWT) were subsequently provided to artificial neural networks to be trained to represent different patterns of the movement tracks before and after treatments of the insecticide. This combined model of wavelets and artificial neural networks was able to point out the occurrence of characteristic movement patterns, and could be an alternative tool for automatically detecting presences of toxic chemicals for water quality monitoring. quality monitoring.

• Korean Journal of Social Welfare Studies
• /
• v.40 no.3
• /
• pp.377-406
• /
• 2009

This study used laten class growth analysis to identify discrete developmental patterns of delinquent behaviors in adolescence. This present article also examined associations among these trajectories to determine how the development of delinquent behaviors relates to protective and risk factors, which include parental monitoring, attachment with parent, association with deviant peers, self-control, and negative stigma from others. Four-wave panel data from a Korea Youth Panel Study were used for the latent class growth model analysis. The sample consisted of 3,446 adolescents who were assessed at 4 measurement waves with approximately 1-year interval. Four trajectories of delinquent behaviors emerged: delinquency persistence, delinquency increaser, delinquency decreaser, normative group(almost no delinquent behaviors). Association with deviant peers had the most proximal strong influence on the probability of being in the delinquency increaser and delinquency persistence group compared, noed to the normative group. Parental monitoring, self-efficacy and negative stigma also differentiated the four delinquent behavior trajectories from one another after controllig for socio-demographic variables. The study suggested that there is a significant heterogeneity in the timing and change rate of delinquency progression. Adolescent delinquency prevention and intervention programs will need to consider this heterogeneity and enhance attention to protective and risk factors depending on the subpopulation.

• Korean Journal of Remote Sensing
• /
• v.34 no.6_3
• /
• pp.1383-1398
• /
• 2018

Sea surface wind is one of the most fundamental variables for understanding diverse marine phenomena. Although scatterometers have produced global wind field data since the early 1990's, the data has been used limitedly in oceanic applications due to it slow spatial resolution, especially at coastal regions. Synthetic Aperture Radar (SAR) is capable to produce high resolution wind field data. KOMPSAT-5 is the first Korean satellite equipped with X-band SAR instrument and is able to retrieve the sea surface wind. This study presents the validation results of sea surface wind derived from the KOMPSAT-5 backscattering coefficient data for the first time. We collected 18 KOMPSAT-5 ES mode data to produce a matchup database collocated with buoy stations. In order to calculate the accurate wind speed, we preprocessed the SAR data, including land masking, speckle noise reduction, and ship detection, and converted the in-situ wind to 10-m neutral wind as reference wind data using Liu-Katsaros-Businger (LKB) model. The sea surface winds based on XMOD2 show root-mean-square errors of about $2.41-2.74m\;s^{-1}$ depending on backscattering coefficient conversion equations. In-depth analyses on the wind speed errors derived from KOMPSAT-5 backscattering coefficient data reveal the existence of diverse potential error factors such as image quality related to range ambiguity, discrete and discontinuous distribution of incidence angle, change in marine atmospheric environment, impacts on atmospheric gravity waves, ocean wave spectrum, and internal wave.

• Structural Engineering and Mechanics
• /
• v.86 no.5
• /
• pp.607-619
• /
• 2023

This study, it was tried to evaluate the asphalt behavior under tensile loading conditions through indirect Brazilian and direct tensile tests, experimentally and numerically. This paper is important from two points of view. The first one, a new test method was developed for the determination of the direct tensile strength of asphalt and its difference was obtained from the indirect test method. The second one, the effects of particle size and loading rate have been cleared on the tensile fracture mechanism. The experimental direct tensile strength of the asphalt specimens was measured in the laboratory using the compression-to-tensile load converting (CTLC) device. Some special types of asphalt specimens were prepared in the form of slabs with a central hole. The CTLC device is then equipped with this specimen and placed in the universal testing machine. Then, the direct tensile strength of asphalt specimens with different sizes of ingredients can be measured at different loading rates in the laboratory. The particle flow code (PFC) was used to numerically simulate the direct tensile strength test of asphalt samples. This numerical modeling technique is based on the versatile discrete element method (DEM). Three different particle diameters were chosen and were tested under three different loading rates. The results show that when the loading rate was 0.016 mm/sec, two tensile cracks were initiated from the left and right of the hole and propagated perpendicular to the loading axis till coalescence to the model boundary. When the loading rate was 0.032 mm/sec, two tensile cracks were initiated from the left and right of the hole and propagated perpendicular to the loading axis. The branching occurs in these cracks. This shows that the crack propagation is under quasi-static conditions. When the loading rate was 0.064 mm/sec, mixed tensile and shear cracks were initiated below the loading walls and branching occurred in these cracks. This shows that the crack propagation is under dynamic conditions. The loading rate increases and the tensile strength increases. Because all defects mobilized under a low loading rate and this led to decreasing the tensile strength. The experimental results for the direct tensile strengths of asphalt specimens of different ingredients were in good accordance with their corresponding results approximated by DEM software.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.26 no.5A
• /
• pp.861-872
• /
• 2006

The element free Galerkin method is extended by the local partition of unity method to model the cohesive cracks in two dimensional continuum. The shape function of a particle whose domain of influence is completely cut by a crack is enriched by the step enrichment function. If the domain of influence contains a crack tip inside, it is enriched by a branch enrichment function which does not have the LEFM stress singularity. The discrete equations are obtained directly from the standard Galerkin method since the enrichment is only for the displacement field, which satisfies the local partition of unity. Because only particles whose domains of influence are influenced by a crack are enriched, the system matrix is still sparse so that the increase of the computational cost is minimized. The condition for crack growth in dynamic problems is obtained from the material instability; when the acoustic tensor loses the positive definiteness, a cohesive crack is inserted to the point so as to change the continuum to a discontiuum. The crack speed is naturally obtained from the criterion. It is found that this method is more accurate and converges faster than the classical meshless methods which are based on the visibility concept. In this paper, several well-known static and dynamic problems were solved to verify the method.

• Journal of Global Scholars of Marketing Science
• /
• v.18 no.3
• /
• pp.115-132
• /
• 2008

Metal industry is one of the most representative heavy industries and the median sales volume of steel and nonferrous metal companies is over one billion dollars in the case America [Forbes 2006]. As seen in the recent business market situation, an increasing number of industrial manufacturers and suppliers are moving from adversarial to cooperative exchange attitudes that support the long-term relationships with their customers. This article presents the results of an empirical study of the antecedent factors of business relationships in metal industry of the United States. Commitment has been reviewed as a significant and critical variable in research on inter-organizational relationships (Hong et al. 2007, Kim et al. 2007). The future stability of any buyer-seller relationship depends upon the commitment made by the interactants to their relationship. Commitment, according to Dwyer et al. [1987], refers to "an implicit or explicit pledge of relational continuity between exchange partners" and they consider commitment to be the most advanced phase of buyer-seller exchange relationship. Bonds are made because the members need their partners in order to do something and this integration on a task basis can be either symbiotic or cooperative (Svensson 2008). To the extent that members seek the same or mutually supporting ends, there will be strong bonds among them. In other words, the principle that affects the strength of bonds is 'economy of decision making' [Turner 1970]. These bonds provide an important idea to study the causes of business long-term relationships in a sense that organizations can be mutually bonded by a common interest in the economic matters. Recently, the framework of structural bonding has been used to study the buyer-seller relationships in industrial marketing [Han and Sung 2008, Williams et al. 1998, Wilson 1995] in that this structural bonding is a crucial part of the theoretical justification for distinguishing discrete transactions from ongoing long-term relationships. The major antecedent factors of buyer commitment such as technology, CLalt, transaction-specific assets, and importance were identified and explored from the perspective of structural bonding. Research hypotheses were developed and tested by using survey data from the middle managers in the metal industry. H1: Level of technology of the relationship partner is positively related to the level of structural bonding between the buyer and the seller. H2: Comparison level of alternatives is negatively related to the level of structural bonding between the buyer and the seller. H3: Amount of the transaction-specific assets is positively related to the level of structural bonding between the buyer and the seller. H4: Importance of the relationship partner is positively related to the level of structural bonding between the buyer and the seller. H5: Level of structural bonding is positively related to the level of commitment to the relationship. To examine the major antecedent factors of industrial buyer's structural bonding and long-term relationship, questionnaire was prepared, mailed out to the sample of 400 purchasing managers of the US metal industry (SIC codes 33 and 34). After a follow-up request, 139 informants returnedthe questionnaires, resulting in a response rate of 35 percent. 134 responses were used in the final analysis after dropping 5 incomplete questionnaires. All measures were analyzed for reliability and validity following the guidelines offered by Churchill [1979] and Anderson and Gerbing [1988]., the results of fitting the model to the data indicated that the hypothesized model provides a good fit to the data. Goodness-of-fit index (GFI = 0.94) and other indices ( chi-square = 78.02 with p-value = 0.13, Adjusted GFI = 0.90, Normed Fit Index = 0.92) indicated that a major proportion of variances and covariances in the data was accounted for by the model as a whole, and all the parameter estimates showed statistical significance as evidenced by large t-values. All the factor loadings were significantly different from zero. On these grounds we judged the hypothesized model to be a reasonable representation of the data. The results from the present study suggest several implications for buyer-seller relationships. Theoretically, we attempted to conceptualize the antecedent factors of buyer-seller long-term relationships from the perspective of structural bondingin metal industry. The four underlying determinants (i.e. technology, CLalt, transaction-specific assets, and importance) of structural bonding are very critical variables of buyer-seller long-term business relationships. Our model of structural bonding makes an attempt to systematically examine the relationship between the antecedent factors of structural bonding and long-term commitment. Managerially, this research provides industrial purchasing managers with a good framework to assess the interaction processes with their partners and, ability to position their business relationships from the perspective of structural bonding. In other words, based on those underlying variables, industrial purchasing managers can determine the strength of the company's relationships with the key suppliers and its state of preparation to be a successful partner with those suppliers. Both the supplying and customer companies can also benefit by using the concept of 'structural bonding' and evaluating their relationships with key business partners from the structural point of view. In general, the results indicate that structural bonding gives a critical impact on the level of relationship commitment. Managerial implications and limitations of the study are also discussed.

• Korean Journal of Social Welfare
• /
• v.60 no.2
• /
• pp.99-129
• /
• 2008

This study analyzed the resilience process of persons with disabilities using the grounded theory approach. To conduct this study, the researcher conducted in-depth interviews with 8 persons with disabilities. In data analysis, this study identified 393 concepts on the resilience process of persons with disabilities and the concepts were categorized into 45 sub-categories and 18 primary categories. In the paradigm model on the resilience process of persons with disabilities, it was identified that casual conditions included 'unawareness of disability before being disability', 'extreme pain', 'repressing psychological pain', and the contingent conditions were 'dis-empowerment by staying in home', 'isolation by himself with difficulty in accepting the disability', 'experience of frustration from social barriers with prejudice against persons with disabilities'. Also, it was identified that the resilience process could be dependent on the type and the degree of the disability, the gender, and the length of time being disability. In spite of the casual and contingent conditions, the central way in which persons with disabilities could acquire resilience was identified as 'enhancement of the power of positive thinking'. The control conditions which accelerate or retard central phenomenon were 'the awareness of not being alone through family, friends, neighborhood and the social system' externally and 'finding purpose in life through religion and help from other persons with disabilities', internally. The action/interactional sequences enhanced the efforts, self searching and active acting, and as a result, persons with disabilities could find comfort in life, participate in society and change the perspective of disability in society. The core categories of resilience process in persons with disabilities were a belief in affirmation and choice of life by initiative. In the process analysis, stages developed in the following: 'pain', 'strangeness', 'reflection', 'daily life'. This stage was more continuous and causal than discrete and complete. In this process, the types of resilience of persons with disabilities are divided into 'existence reflection', 'course development', 'implicit endeavor', and 'active execution'. This study showed the details of the paradigm models, the process and types with an in-depth understanding of the resilience process of persons with disabilities using grounded theory as well as theory construction and policy and clinical involvement on the study of persons with disabilities.