• 한국물환경학회지
• /
• 제32권4호
• /
• pp.375-383
• /
• 2016

Total Pollution Load Control (TPLC) calculates and manages the allowable pollutant load that is discharged from the watershed, which can meet the water quality target. Delivery Ratio (DR) is generally used for predicting the variation of pollutant mass balance between the pollutants discharged from the watershed and a certain point in the stream, and it is very important for estimation of accurate allowable pollutant load. The concept of DR in TPLC is different from prevalent DR, because DR in TPLC includes both the discharge of pollutants from the watershed and the delivery mechanism. Therefore, DR in TPLC should be estimated by using a proper and unified methodology. The appropriate method and equation for estimation of DR in TPLC was developed through the review of various methodologies, and the applicability of the equation was evaluated in a study area (Geumho A). Determination coefficients (R²) of regression were shown to be relatively high (BOD 0.71~0.87, T-N 0.86~0.90, T-P 0.62~0.69). Applicability of the developed methodology and equations was evaluated as appropriate for TPLC, and it is suggested.

• 한국물환경학회지
• /
• 제32권6호
• /
• pp.589-599
• /
• 2016

Implemented since 2004, TPLC (Total Pollution Load Control) is the most powerful water-quality protection program. Recently, uncertainty of prediction using steady state model increased due to changing water environments, and necessity of a dynamic state model, especially the watershed model, gained importance. For application of watershed model on TPLC, it needs to be feasible to adjust the relationship (mass-balance) between discharged loads estimated by technical guidance, and arrived loads based on observed data at the watershed outlet. However, at HSPF, simulation is performed as a semi-distributed model (lumped model) in a sub-basin. Therefore, if the estimated discharged loads from individual pollution source is directly entered as the point source data into the RCHRES module (without delivery ratio), the pollutant load is not reduced properly until it reaches the outlet of the sub-basin. The hypothetic RCHRES generated using the HSPF BMP Reach Toolkit was applied to solve this problem (although this is not the original application of Reach Toolkit). It was observed that the impact of discharged load according to spatial distribution of pollution sources in a sub-basin, could be expressed by multi-segmentation of the hypothetical RCHRES. Thus, the discharged pollutant load could be adjusted easily by modification of the infiltration rate or characteristics of flow control devices.

• 도시과학
• /
• 제10권1호
• /
• pp.39-48
• /
• 2021

In this study, to evaluate the characteristics of the pollution in the major inflow tributaries and major environmental facilities in the watershed of Ara waterway, An inflow flow rate measurement and water quality analysis were conducted during dry and rainy seasons. In addition, the flow rate measurement, water quality analysis, and pollutant load at each monitoring point were compared and evaluated. Influx of BOD5, T-P and T-N into the tributaries of the ARA waterway watershed, excluding the Gulpo river watershed, during dry season were only 0.007%, 0.005% and 0.004% respectively of the incoming loads in the entire ARA waterway basin. In addition, it was confirmed that the discharge pollutant loads during rainfall event was about 440 times more for BOD5, about 545 times on T-P, and about 23 times on T-N in comparison to the pollutant loads during the dry days. When the Gulhyeon rubber dam was deflated, the discharged pollutant load during a rainfall was higher than the estimated load at the G7 monitoring point because the deposited pollutants from the upstream riverbed flowed down. Therefore, during a rainy season, it is necessary to manage the influx of high-load water pollutants from the overflow and deflation of the Gulhyun rubber dam as well as to find a strategy to reduce the pollutant loads in the Gulpo river watershed.

• Spatial Information Research
• /
• 제4권2호
• /
• pp.147-157
• /
• 1996

노촌 소유역에서 발생된 오염물질의 이동과 이에 따른 하천의 수질변화를 공간적으로 파악하기 위하여 이와 관련된 기존의 모형들과 지리정보시스템을 통합함으로써 소유역 하천수질관리시스템을 개발하였다. 오염 물질의 하천유달률을 계산하기 위한 간단한 오염부하모형, 유역의 유출을 발생시키기 위한 Tank모형 그리고 하천에서의 수질을 예측하기 위한 QUAL2E모형이 본 연구에 적용되었다. 시스템은 경기도 이천군과 용인군에 위치한 복하천유역에 적용하였으며, 발생오염물질 분포도, 배출오염물질 분포도, 하천으로의 유달률 분포도 및 주요하천지점에서의 수질현황도 등을 구축하였다.

• 생태와환경
• /
• 제38권spc호
• /
• pp.67-75
• /
• 2005

The objectives of this study were to understand the runoff characteristics of the non-point sources originating from impervious surfaces and to assess their effect on the aquatic environment in the urban areas. The concentration of pollutants (SS, BOD, COD and T-P) except for T-N showed the highest value in runoff from road, and event mean concentration (EMC) also showed high value from road. The pollutants discharged from road showed a higher concentration in the beginning stage (0 ${\sim}$ 30%) of progressive percentage of rainfall. The contribution percentages of non-point sources by load were 44.9% for SS, 11.2% for BOD, 21.4% for COD, 11.4% for T-N and 8.1% for T-P in the total load of pollutant discharged through sewer. From our results, the road was a significant potential source that deteriorated water quality of the streams and lakes in the vicinity of the urban area during the rain period. Therefore, counter plan is required to reduce pollutant concentration on the road from non-point sources in the urban area. Also, since pollutant concentration in the beginning stage of rainfall was quite high, road cleaning seems to be one of the very useful methods to prevent inflowing of pollutants to the aquatic environment.

• 한국도로학회논문집
• /
• 제9권4호
• /
• pp.185-192
• /
• 2007

최근의 환경정책은 신설되는 도로에 대하여 비점오염저감시설 설치의무화를 요구하고 있다. 또한 도로건설시 및 유지관리시에는 발생가능한 비점오염물질을 예측하고 이를 저감할 수 있는 방향으로 노선의 계획 및 설계와 더불어 다양한 비점저감방안을 수립할 것을 요구하고 있다. 비점오염원 및 비점오염물질을 관리하기 위해서는 우선 유역의 토지이용도를 분석하여 강우시 배출되는 오염물질의 종류와 양을 산정해야 한다. 특히 도로의 경우, 발생되는 비점오염물질의 원단위가 별도로 존재하지 않고 대지항목의 오염발생원단위를 사용하고 있기에 적용함에 있어서 많은 어려움을 겪고 있는 실정이다. 따라서 본 연구는 포장지역 중 고속도로 영업소를 대상으로 강우시 유출되는 강우유출수의 특성을 파악하여, 이러한 토지이용에서의 비점오염물질 유출특성과 부하량을 산정하고자 한다. 영업소 토지이용의 경우 많은 차량이 속도를 급격히 줄이는 토지이용지역으로 브레이크 패드, 각종 오일 및 엔진파트 등으로부터 많은 양의 오염물질이 축적되고, 포장률이 높아 강우시 다량의 오염물질이 유출되는 지역이다. 본 연구를 통해서 영업소 토지이용지역에서의 초기강우현상을 수리수문 및 농도곡선을 통해 확인할 수 있었다. 또한 EMC로부터 단위면적당 부하량과 강우지속시간당 부하량을 산정하였으며, 이러한 값은 영업소 유지관리시 인근수계에의 환경적인 영향을 해석하기 위한 기초자료로 활용될 수 있다. 강우지속시간당 유출되는 평균부하량은 TSS의 경우 $533.7mg/m^2-hr$, COD $396.2mg/m^2-hr$, TN $17.0mg/m^2-hr$, TP $4.8mg/m^2-hr$로 산정되었다.

• 한국물환경학회지
• /
• 제35권1호
• /
• pp.43-54
• /
• 2019

The objective of this study was to assess the effect of policies on water quality management based on the changes in pollutants and water quality in Special Water Preservation Area (SWPA) of Lake Paldang watershed from 1990 to 2016. The population, total sewage and flow rate of wastewater in SWPA continuously increased from 1990 to 2016, while the location of new facilities for industrial and livestock facilities has been restricted. However, unlike the buffer zone in which industrial and livestock facilities were continuously reduced after implementing of TMDL, it was found that the effect of land-use regulations on industrial and livestock facilities in SWPA were mitigated by the increase in the size of large facilities. Since 1999 when the emission standard of public sewage treatment plants (STP) was changed, the water quality of Lake Paldang has increased despite the increase of pollutant source. Since emission standard of STP changed in 2012 (BOD 5 mg/L, TP 0.2 mg/L), BOD concentration in Lake Paldang has also improved to the level of water quality in the early 1990s where as TP concentration has remained at its lowest since 1990. BOD and TP average discharge concentration of 43 STP (${\geq}500m^3/day$) in 2016 have been maintained $1.7{\pm}0.7mg/L$ and $0.06{\pm}0.02mg/L$ respectively. While the discharged load of STP in SWPA was decreased by the concentration management, the contribution rate to the total discharged load of non-point pollutants increased to 70 % in 2015, and the contribution rate to the point discharged load of individual treatment facilities increased to 80 %.

• 대한환경공학회지
• /
• 제36권10호
• /
• pp.719-723
• /
• 2014

수질오염총량관리제의 효율적인 시행을 위해 본 연구에서는 비점오염원의 분류, 비점부하량(발생, 배출) 산정, 비점 오염원 관리지역의 선정, 비점오염물질 관리 등을 포함한 비점오염원 관리방안을 제시하고자 하였다. 무엇보다도 먼저 점오염원과 비점오염원의 정의는 학술적 법률적 관점에 기초하여 명확히 구분 관리하여야 한다. 특히, 사업활동과 사람의 활동에 의해서도 환경피해가 발생하지 않는 임야, 초지, 하천 등은 별도로 자연배경오염원으로 구분하여야 한다. 비점오염원 발생 및 배출부하량의 원단위는 유역의 실제여건에 맞도록 우선적으로 변경하여야 하며, 비점오염원 발생 및 배출부하량의 산정방법은 유역의 강수량 및 강수 지속시간을 고려하도록 수정하여야 한다. 한편, 수질오염총량관리제를 시행함에 있어 비점 오염원 관리지역은 강우시 하천의 오염물질 농도가 중권역 목표(관리목표)를 초과하거나 초과할 우려가 있는 유역을 대상으로 하며, 전체 유역 가운데 초지, 임야를 제외한 도시지역, 농경지, 그리고 대지 가운데 비점오염물질의 배출밀도가 높은 지역을 비점오염원 관리지역으로 최소화하여 선정하여야 한다. 비점오염물질저감시설은 단위면적당 비점오염물질 배출량, 오염물질 초과농도 지속시간, 처리의 실현가능성, 점오염원 대비 처리비용 효과 등을 고려하여 단위면적당 비점오염원 발생부 하량이 많은 지역과 강우시 수질농도가 중권역 목표를 초과하는 유역에 설치하여야 한다.

• 한국물환경학회지
• /
• 제26권4호
• /
• pp.654-663
• /
• 2010

Attention has increasingly focused on the pollutant load discharged from rural area since the enforcement of total maximum daily loads (TMDLs) in korea. As one of the methods to control the inflow of pollutant load during wet weather events, local governments are attempting to apply non-point source control facility. To design those facilities appropriately, it is essential to understand the runoff characteristics of pollutants such as TSS, $BOD_5$, $COD_{Cr}$, TP and TN. In the paper, the quantitative analyses for pollutant runoff characteristics were examined in a small rural watershed with the area of about 53 hectares. For a dry weather day and wet weather events, variation patterns of dry weather flow and runoff characteristics of wet weather flows were monitored and investigated. The runoff model using XP-SWMM reflecting the landuse types of the watershed in detail was simulated to perform the sensitivity analyses for several factors influencing on their hydrograph and pollutographs. As a result, for the case of medium and small rainfall events (i. e. total rainfall of 35.8 and 17.5 mm), the impervious area including green house, roof and road which covers relatively low portion of total area (i. e. 16%) caused substantial first flush and the majority of total runoff load. Therefore, it has been concluded that the runoff characteristics of each pollutant and distribution of impervious area should be considered for the establishment of the control strategy of non-point pollutant runoff at a rural area.

• 한국물환경학회지
• /
• 제30권6호
• /
• pp.585-595
• /
• 2014

The temporal trends of the prioritized toxic water pollutants generated and discharged from the industrial facilities in the Geum-River basin, Korea were analyzed with the results of the nationwide Water Pollution Source Survey conducted in 2001 - 2012. The statistical results indicated rapid increase in the volume of raw toxic wastewaters whereas the amount of each toxic pollutant kept fluctuating for 12 years. Serious discrepancies in the survey data of the same type of industries demonstrated a low reliability of the survey result, which stemmed from several error factors. A unit-load for each type of industrial facility was devised to estimate the amount of prioritized toxic water pollutant based on the total volume of industrial wastewater generated from the same type of industrial facilities. The supplementary measures with an effective permit issuance policy and adding survey parameters of terminal wastewater treatment plants to use them as references to the Water Pollution Source Survey were suggested as means to minimize the errors associated with the false reports from the industries.