• Journal of the Korean Institute of Gas
• /
• v.20 no.2
• /
• pp.1-9
• /
• 2016

Combined removal of n-heptane and carbon monoxide (CO) using a plasma-catalytic process was investigated. The performance of the plasma-catalytic process was compared with that of the catalyst-alone process to characterize the decomposition of n-heptane and CO with the operation parameters such as the type of catalyst, reaction temperature, and discharge power. From several sets of experiments, it was found that the decomposition efficiency of n-heptane mainly depended on the specific input energy rather than the reactor temperature, whereas the oxidation of CO on both the energy density and the reaction temperature. The results conducted over several metal oxide catalysts exhibited that the decomposition efficiency of n-heptane was in the order: $Pd/{\gamma}-Al_2O_3$ > $Ru/{\gamma}-Al_2O_3{\approx}Ag/{\gamma}-Al_2O_3$. Especially, $Pd/{\gamma}-Al_2O_3$ catalyst did hardly generate CO as a byproduct during the decomposition of n-heptane under an appropriate condition, revealing $CO_2$ selectivity of nearly 100%. The CO oxidation efficiency was largely affected by the type of catalyst ($Pd/{\gamma}-Al_2O_3$ > $Ru/{\gamma}-Al_2O_3$ > $Ag/{\gamma}-Al_2O_3$). At temperatures below $180^{\circ}C$, the plasma-catalytic process was more effective in the oxidation of CO, while above $180^{\circ}C$, the catalytic process resulted in slightly higher CO oxidation efficiency.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.35 no.5
• /
• pp.1039-1049
• /
• 2015

The inflow estimation at large multipurpose dam reservoir is carried out by considering the water balance among the discharge, the storage change during unit time interval obtained from the observed water level near dam structure and area-volume curve. This method can be ideal for level pool reservoir but include potential errors when the inflow is influenced by the water level slope due to backwater effects from upstream flood inflows and strong wind induced by typhoon. In addition, the other uncertainties arisen from the storage reduction due to sedimentation after the dam construction and water level noise due to mechanical vibration transmitted from the electric power generator. These uncertainties impedes the accurate hydraulic inflow measurement requiring exquisite hydrometric data arrangement for reservoir waterbody. In this study, the distributed hydrologic model using UBC-3P boundary setting was applied and its feasibility was evaluated. Finally, the modeling performance has been verified since the calculated determination coefficient has been in between 0.96 to 0.99 after comparing with observed peak inflow and total inflow at Namgang dam reservoir.

• Women's Health Nursing
• /
• v.1 no.1
• /
• pp.119-137
• /
• 1995

Maternity nurses' roles are to find out women's various responses related to the health problems during pregnancy, to intervene adequate nursing and supports, and to help them adapt satisfactorily to new situation, such as hospitalization. The purposes of this study are : firstly, to inquire about women's emotional status, feeling of discomfort, and the nursing need during hospitalization because of discomfort, and the nursing needs during hospitalization because of the possibility of abortion by threatened and habitual abortion : secondly, to provide fundamental data for developing adequate nursing intervention and improving hospital management. The subjects of this study were 62 women who were hospitalized, visited out-patient clinic for follow-up, and stayed at home after discharge since August, 1993 from one hospital located in Seoul, from March 23 to April 13, 1994. The questionnaire was consisted of 21 items of emotion(Reliability Cronbach's alpa, .77), 19 items of feeling of discomfort(.79), and 21 items of nursing needs (.89), and nurses' performance according to nursing needs,(.90). These were measured by using Likert Scale and analyzed by using SPSS / $PC^+$ with the descriptive statistics, $X^2$-test, and ANOVA. Research findings are as follows : 1) The subjects' average age, hospitalized days, and gestational age are 32.2, 15.7, 12.9 by respectively. 2) 88.7% of the subjects are getting antepatal care, 66.1% are experiencing 1.75 times of spontaneous abortion, and 82.3% are nuclear family. 3) The Emotions were mainly comprized negative and subjective state of minds such as uneasiness, anxiety, and discomfort. The domains of emotions were related to 'fetus', 'herself', 'hospitalization', and 'husband's 'families', in rank. The highest scored item was "I, above anyone else, am mostly stressed from abortion." 4) The feelings of discomforts were firstly related to 'personal discomfort arising from absolute bed rest', 'meals provided', Usage of hospital, perse', 'health team', in rank. 5) The nursing needs frequently pointed out were 'Nurses kindly explain of me the purpose, method, and results of the lab. test', 'Nurses sincerely pay attention to my word in communication'. The least nursing needs were 'Nurses observe my feces and whether I have constipation or not'. 'When I can't move, nurses help me by holding my arms or pulling my bed'. 6) The highest performed items were 'Nurses observe whether I bleed or not', and 'Nurses give me drug with exact dose in time'. The least performed items was about hospital environment, such as 'Temperature, ventilation & humidity in the room should be controlled'. 7) Besides religion that is related to nursing need with statistically significant difference, none of general characteristics were related to emotion, feeling of discomfort, and nursing needs.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.40 no.3
• /
• pp.191-200
• /
• 2016

The ventilation effect of a ventilation system, which is classified as the forced ventilation and natural ventilation, is predominantly dependent on the combination of air supply and discharge. Perhaps the simplest ventilation is merely supplying the air as it is. However, to improve the indoor working environment during the summer, an air supply that is cooled to some extent has been widely adopted. Recently, a cooling method utilizing the vaporization of water was introduced. In this study, the performance of an evaporation-type air supply unit that was produced by Japan K-company and was installed in a shoe-manufacturing plant in Busan was investigated. The purpose of the experiment was to measure how much the supplied air could be cooled. From this experimental study, we confirmed that the evaporation-type air supply system is efficient, capable of improving the working environment during the summer while minimizing the energy cost.

• Journal of IKEEE
• /
• v.24 no.3
• /
• pp.913-916
• /
• 2020

In this paper, we propose the development of nitrogen cooling equipment for personalized local area. The proposed equipment consists of a cold air supply module, a body, and nitrogen injection with the following characteristics. First, it automatically controls the amount and time of cold air supply by utilizing information measuring skin temperature with volumetric temperature sensors, so it can have a competitive edge in function by ensuring complete safety. Second, if the distance measuring sensor is applied to the skin for more than a certain distance, it can block the cold air or control the discharge of nitrogen in conjunction with the control GUI to improve the efficiency of higher cooling therapy while providing safe management. Third, by installing a control module that can control the supply of nitrogen, the cost of maintenance can be minimized by minimizing the loss of nitrogen. Experiments at an external testing agency to evaluate the performance of the proposed equipment showed that the accuracy of the temperature sensor was measured in the range of ±3.8%, which is lower than the world's highest level(±5%), with a range of 110℃ to -160℃ similar to the world's highest level. Distance accuracy was measured in the range of ±3.0%, lower than the world's highest level(±5%), and weight accuracy in the range of ±0.1%, lower than the world's highest level(±5%). In addition, emission control was measured in four stages, higher than the world's highest level(stage 1) and nitrogen use was measured at 0.8L/min below the world's highest(6L/min). Therefore, the effectiveness of the methods proposed in this paper was demonstrated because they produced the same results as the world's highest levels.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.19 no.9
• /
• pp.69-76
• /
• 2018

The present study analyzed the effect of film hole position of 45 degree ribbed cooling channel on film cooling performance of gas turbine blades. We also investigated the influence of the ribs under the fixed blowing ratio. Three-dimensional numerical model was constructed and extensive simulation was conducted using the commercial code (Fluent ver. 17.0) under steady-state condition. Base on the simulation results, We investigated the cooling effectiveness, flow velocity, streamline, and pressure coefficient. Moreover, We analyzed the effect of cooling hole position on ejection of the secondary flow caused by the rib structure. From the results, It was found that internal flow of the cooling channel forms a vortex pair in the counterclockwise from the top side, and clockwise from the bottom side. For the channels with ribs, the vortex flow generated by the ribs caused a higher pressure difference near the hole outlet, resulting in at least 12% higher cooling effectiveness than the channel without ribs. Additionally, when the hole is located on the left side of the ribbed channel (Rib-Left), it can be found that the secondary flow generated by the ribs hits against wall surface near the hole to form a flow in the direction of the hole inclination angle. Therefore, It is considered that the region where the cooling gas discharged to the blade surface stays in the main flow boundary layer is wider than the other cases. In this case, The largest pressure coefficient difference was observed near the outlet of the hole, and as a result, the discharge of the cooling gas was accelerated and the cooling efficiency was slightly increased.

• Journal of the Korea Concrete Institute
• /
• v.18 no.4 s.94
• /
• pp.449-458
• /
• 2006

The discharge of fly ash that is produced by coal-fired electric power plants is rapidly increasing in Korea. The utilization of fly ash in the raw materials would contribute to the elimination of an environmental problem and to the development of new high-performance materials. So it is needed to study the binder obtained by chemically activation of pozzolanic materials by means of a substitute for the cement. Fly ash consists of a glass phase. As it is produced from high temperature, it is a chemically stable material. Fly ash mostly consists of $SiO_2\;and\;Al_2O_3$, and it assumes the form of an oxide in the inside of fly ash. Because this reaction has not broken out by itself, it is need to supply it with additional $OH^-$ through alkali activators. Alkali activators were used for supplying it with additional $OH^-$. This paper concentrated on the strength development according to the kind of chemical activators, the curing temperature, the heat curing time. Also, according to scanning electron microscopy and X-Ray diffraction, the main reaction product in the alkali activated fly ash mortar is Zeolite of $Na_6-(AlO_2)_6-(SiO_2)_{10}-12H_2O$ type.

• Journal of the Korean Electrochemical Society
• /
• v.4 no.3
• /
• pp.104-108
• /
• 2001

Naphthalene derived mesophase pitch WP) was spun into short fibers by using melt-blown technology. The pitch fibers oxidative stabilization were carried out heating rates of $2^{\circ}C/min,\;5^{\circ}C/min\;and\; 10^{\circ}/min$. The heating rate was a key factor to maximate the capacity of the Li-ion secondary battery through controlling the morphology of the graphitized fiber. The diameters of the melt-blown fibers prepared were in the range of $4{\mu}m\~16{\mu}m$ with functions of air jet speed, air temperature and the temperature of the nozzle. The graphitized fibers of $10{\mu}m$ diameters showed various morphological structure with heating rate of the stabilization. Radial, radial-random and skin-core cross-sectional structure of the fibers were observed at the respective heating rate of $2^{\circ}C/min\;5^{\circ}C/min\;and\;10^{\circ}C/min$. Most crystalline structure of graphite was obtained from the fiber stabilized at heating rate of $10^{\circ}C/min$ exhibiting the best anode performance with 400 mAh/g of capacitance and $96.8\%$ of charge/discharge efficiency.

• Journal of the Korean Electrochemical Society
• /
• v.5 no.2
• /
• pp.47-51
• /
• 2002

Polyurethane was used as matrix for polymer electrolytes with liquid electrolyte consist of organic solvent as ethylene carbonate(EC), propylene carbonate(PC), and tetraethylene glycol dimethylether(TG) and 1M $LiCF_3SO_3$, which has high mechanical strength and porosity. Electrochemical properties fur polyurethane electrolytes with various liquid electrolytes were evaluated. The amount of immersed liquid electrolyte for TG with 1M $LiCF_3SO_3$ was increased to about $750\%$ by weight, and initial discharge capacity and cycle performance was better than others. Ionic conductivity for TG/EC(v/v,1:1) and PC/EC(v/v, 1:1) with 1M $LiCF_3SO_3$ was about $3.15\times10^{-3} S/cm, \;3.18\times10^{-3}S/cm$

• Journal of Biosystems Engineering
• /
• v.22 no.4
• /
• pp.469-478
• /
• 1997

This study was conducted to develop an automatic nutrient-solution mixing system for small-scale sewers. The nutrient-solution mixing system consisted of a low-cost and precise metering device and data acquisition ＆ control system with a personal computer. and, the metering device was composed of three parts those were supply pumps, metering cylinders and venturi tube. The system controlled electric conductivity(EC) and pH of nutrient-solution based on the time-based feedback control method with the information about temperature, EC, and pH of the nutrient-solution. The performance of the nutrient-solution mixing system was evaluated through the control of EC and pH while compared with those of commercial system. Also an experimental cultivation of tomato was conducted to verify and to improve the developed system. Results of this study were as follows. 1. The correlation coefficient of meteing device between the flow rate and operating time was 0.9999, and the linear reuession equation computed was y=21.759x, where y is the discharge($g$) and x is the operating time(s). 2. Calculated errors for the developed metering device and two commercial pump were $\pm$0.3% $\pm$2.45% and $\pm$1.38 % FS error respectively. 3. An automatic nutrient-solution mixing system based on a low-cost and precise metering device was developed. 4. The full scale errors of the developed system in controlling EC and pH at 23$\pm$1$^{\circ}C$ were $\pm$0.05mS/cm and $\pm$0.2, respectively 5. When using the commercial system, the controlled values of EC and pH of the 500 $\ell$ of water were 1.29 mS/cm and 6.1 pH for the setting points of 1.4 mS/cm and 6.0 pH respectively at 23$pm1^{\circ}C$. 6. The developed nutrient-solution control system showed $\pm$0.05 ms/cm of deviation from the setting EC value over the experimental cultivation period. 7. The deviation from the average values of Ca and Mg mass content in the several nutrient-solution were 0.5% and 1.8% respectively.