• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2007년도 춘계학술대회A
• /
• pp.1213-1218
• /
• 2007

The brake judder comes from non-uniformities in the tire/wheel assembly caused by mechanical effects such as a brake torque variation (BTV). A disc thickness variation (DTV) related with the kinematic behavior of the disc was investigated a main source of BTV. In this study, a dynamic model with brake corner assembly of full vehicle using MSC.ADAMS was correlated by experiment of judder phenomenon. Judder was generated and correlated systematically by judder experiment in chassis and brake dynamometer from variation in the thickness of the disc. Also it has been found a judder transfer path and variation of the braking pressure. Through analysis of transfer function and movement of subsystem caused by BTV generation, design parameters have been found. Based on the results obtained from parameter study of suspension module, the effective design process and developed model with brake corner assembly was suggested for vibration reduction of steering wheel caused by the judder phenomenon.

• 한국소음진동공학회논문집
• /
• 제12권5호
• /
• pp.338-345
• /
• 2002

The study presents a new testing and analysis method for brake judder on vehicle. For the identification of the excitation mechanism of a brake judder, it is necessary to measure the dynamic brake disc geometry during braking on vehicle. The non-contact sensor system was used to monitor the brake disc geometry. Brake torque variation (BTV) caused by disc thickness variation (DTV) is the primary excitation for brake judder. The mechanical effects generating BTV are linked not only to initial manufacturing tolerances but also to uneven wear. Therefore, the brake disc geometry should be strictly managed to initial condition. The aim of this study has been to measure the dynamic DTV and runout on vehicle and analyze the influence of test parameters on brake judder and compare the disc component with vehicle matching about the DTV Profile. As a result of this study, The amplitude of brake judder is proportional to vehicle speed and fluid pressure fluctuation on braking. The major sources of brake judder are directly related to disc thickness variation and side runout variation of corner assembly (disc, hub. bearing).

• Structural Engineering and Mechanics
• /
• 제62권5호
• /
• pp.587-593
• /
• 2017

The objective of this analytical study is to calculate the elasto-plastic stresses of Functionally Graded (FG) hyperbolic disc subjected to uniform temperature. The material properties (elastic modulus, thermal expansion coefficient and yield strength) and the geometry (thickness) of the disc are assumed to vary radially with a power law function, but Poisson's ratio does not vary. FG disc material is assumed to be non-work hardening. Radial and tangential stresses are obtained for various thickness profile, temperature and material properties. The results indicate that thickness profile and volume fractions of constituent materials play very important role on the thermal stresses of the FG hyperbolic discs. It is seen that thermal stresses in a disc with variable thickness are lower than those with constant thickness at the same temperature. As a result of this, variations in the thickness profile increase the operation temperature. Moreover, thickness variation in the discs provides a significant weight reduction. A disc with lower rigidity at the inner surface according to the outer surface should be selected to obtain almost homogenous stress distribution and to increase resistance to temperature. So, discs, which have more rigid region at the outer surface, are more useful in terms of resistance to temperature.

• 한국윤활학회:학술대회논문집
• /
• 한국윤활학회 2002년도 제35회 춘계학술대회
• /
• pp.235-239
• /
• 2002

The objective of the experiment is to investigate the effect of microstructures of gray cast iron oil wear characteristics of automotive disc brakes. Six different gray cast iron rotors were manufactured by changing carbon equivalent and cooling rate. The change of DTV (disc thickness variation) before and after wear tests was measured to examine the wear properties according to the microstructures of gray iron discs since the DTV generation is caused by the circumferential uneven wear. Experimental results showed that the morphology of graphite flake and hardness in gray cast iron were crucially associated with the change of DTV. In particular, the DTV changes of rotor decrease when the length and area fraction of graphite flake in brake rotors increase and hardness of brake discs reduces.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2004년도 춘계학술대회논문집
• /
• pp.346-350
• /
• 2004

In Blu-ray(BD) optical system, as a short laser wavelength of laser diode and thin cover layer thickness of' disc, the proper adjustment of spherical aberration should be performed. Considering thin cover layer' thickness and tolerance variation of disc in BD optical system, spherical aberration in BD format is mort: serious than CDㆍDVD format Especially, in dual-layer disc, to compensate the aberration at each layer, optical component should be moved finely in the way of optical path. In this study, 1 -axis moving actuator was introduced as the method of compensating the spherical aberration, and the mechanism of the system was described. Finally, its effect on optical system will be mentioned.

• 정보저장시스템학회논문집
• /
• 제2권3호
• /
• pp.178-183
• /
• 2006

A Blu-ray disc, which has a more than 25GB optical capacity, has been known as a promising next-generation optical disc format. It commonly has a 1.1 mm thick substrate and a 0.1 mm thick cover layer for beam transmitting and the protection of the reflecting surface. The cover layer is generally formed by the spin coating process. However, in conventional spin coating, small bumps are formed along the rim of the disc, which results in the fatal reading error. Numerical simulation of the thin film flow behaviors during spin coating with the commercial solver and optimal spinning conditions was obtained. Thickness distribution of the cover layer according to the variation of substrate's edge shape could be calculated as well. By modifying the shape of the substrate edge shape, the bumps along the disc rim could be minimized, and it was proved that the chamfered edge, around $5{\sim}10$ degree, is the simplest and most effective way to minimize the bumps.

• Restorative Dentistry and Endodontics
• /
• 제25권1호
• /
• pp.17-40
• /
• 2000

Resin cements are used for cementing indirect esthetic restorations such as resin or porcelain inlays. Because of its limitations in curing of purely light cured resin cements due to attenuation of the curing light by intervening materials, dual cured resin cements are recommended for cementing restorations. The physical properties of resin cements are greatly influenced by the extent to which a resin cures and the degree of cure is an important factor in the success of the inlay. The purpose of this study was to evaluate the influence of porcelain thickness and exposure time on the polymerization of resin cements by measuring the microhardness and the degree of conversion, to investigate the nature of the correlation between two methods mentioned above, and to determine the exposure time needed to harden resin cements through various thickness of porcelain. The degree of resin cure was evaluated by the measurements of microhardness [Vickers Hardness Number(VHN)] and degree of conversion(DC), as determined by Fourier Transform Infrared Spectroscopy(FTIR) on one light cured composite resin [Z-100(Z)] and three dual cured resin cements [Duo cement(D), 3M Resin cement(R), and Dual cement(DA)] which were cured under porcelain discs thickness of 0mm, 1mm, 2mm, 3mm with light exposure time of 40sec, 80sec, 120sec, and regression analysis was performed to determine the correlation between VHN and DC. In addition, to determine the exposure time needed to harden resin cements under various thickness of porcelain discs, the changes of the intensity of light attenuated by 1mm, 2mm, and 3mm thickness of porcelain discs were measured using the curing radiometer. The results were obtained as follows ; 1. The values of microhardness and the degree of conversion of resin cements without intervening porcelain discs were 31~109VHN and 51~63%, respectively. In the microhardness Z was the highest, followed by R, D, DA. In the degree of conversion, D and DA was significantly greater than Z and R(p<0.05). 2. The microhardness and the degree of conversion of the resin cements decreased with increasing thickness of porcelain discs, and increased with increasing exposure time, D and R showed great variation with inlay thickness and exposure time, whereas, DA showed a little variation. 3. The intensity of light through 1mm, 2mm, and 3mm porcelain inlays decreased by 0.43, 0.25, and 0.14 times compared to direct illumination, and the respective needed exposure times are 53 sec, 70 sec, and 93 sec. In D and R, 40 sec of light irradiation through 2mm porcelain disc and 80 sec of light irradiation through 3mm porcelain disc were not enough to complete curing. 4. The microhardness and the degree of conversion of the resin cements showed a positive correlationship(R=0.791~0.965) in the order of R, D, Z, DA. As the thickness of porcelain discs increased, the decreasing pattern of microhardness was different from that of the degree of conversion, however.

• 한국정밀공학회지
• /
• 제27권8호
• /
• pp.35-41
• /
• 2010

White Etching Layer(WEL) is a phenomenon that occurs on the surface of rail due to wheel/rail interactions such as excessive braking and acceleration. Rolling Contact Fatigue(RCF) cracks on the surface of rail have been found to be associated with WEL. In this study, we have investigated RCF damages of white etching layer using twin disc testing and fatigue analysis. These tests consist of wheel flat tests and rolling contact fatigue tests. WEL has been simulated by wheel flat test. It has been founded that the WEL with a bright featureless contrast is formed on the surface of specimen by etching. Rolling contact fatigue test was conducted by using flat specimens with the WEL generated by the wheel flat test. It has been observed that two types of cracks occur within the specimen. The contact fatigue test was simulated in 2D elastic-plastic FE simulations. Based on loading cycles obtained from the finite element analysis, the fatigue life analysis according to the thickness variation of WEL was carried out. The longest fatigue life was observed from the thickness of 20um.

• Tribology and Lubricants
• /
• 제14권1호
• /
• pp.85-93
• /
• 1998

The Bair & Winer's limiting shear stress rheological model is incorporated into the Reynolds equation to successfully predict the traction and film thickness for an isothermal line contact using the primary rheological properties. The modified WLF viscosity model and Barus viscosity model are also adapted for the realistic prediction of EHD tractional behavior. The influences of the limiting shear stress and slide-roll ratio on the pressure spike, film thickness, distribution of shear stress and nonlinear variation of traction are examined. A good agreement between the disc machine experiments and numerical traction prediction has been established. The film thickness due to non-Newtonian effects does not deviate significantly from the fdm thicknesss with Newtonian lubricant.

• 자동차안전학회지
• /
• 제7권2호
• /
• pp.19-24
• /
• 2015

Ferritic Nitro Carburizing (FNC) cast iron brake discs is known to improve corrosion resistance and brake creep groan noise as well as prevent corrosion-induced pulsation. But, it is necessary to treat honing machining on braking surface to avoid grinding noise during braking.