• Toxicological Research
• /
• 제5권2호
• /
• pp.97-104
• /
• 1989

A new exposure system was developed to generate p-dinitrobenzene (p-DNB) containing atmosphere. A glass column was filled with small glass beads coated with the chemical. The p-DNB containing medium was heated to a temperature beyond the boiling point of p-DNB. A stream of air flow was forced to pass through the column and let it mixed with fresh air before introducing into an inhalation chamber. The concentration of p-DNB in the chamber air was measured by direct assaying the air directly and by sampling the chemical using a microfilter installed in the chamber.

• 한국정밀공학회지
• /
• 제9권4호
• /
• pp.90-99
• /
• 1992

In resent year Laser Speckle and its development have enabled surface deformation of engineering components and materials to be interferometrically examined. Laser Speckle- Pettern Interferometry Method is a very useful method for measuring In-plane components of displacement. In measuring thermal expansion coefficient, the various problems generated were established, and the measuring limitation examined. Metarial INCONEL 601 was used in experiments. Specimen was heated to the high temperature(100$0^{\circ}C$) by diong current to the direct two specimen. Then, those problems appear to the influence of back-ground radiation by the heated specimen, the influence by air turbulence, the oxidation of specimen. The color monitor and interference filter prevented the back-ground radiation by rad heat. The oxidation occuring in specimen itself was not generated by the being acid-proof excellence of material INCONEL 601. Yet, in this experiments, the serious problems are the oxidation of specimen and influence by air turbulence. By more reserching these problems forward, it is helpful that the thermal expansion coefficient of many materials is directly measured under high temperature.

• 설비공학논문집
• /
• 제13권8호
• /
• pp.674-681
• /
• 2001

An experiment is conducted to investigate the effect of the inclination angle on convective boiling heat transfer of a uniformly heated tube. The test section used is a stainless steel tube with10.7mm in inner diameter. The hating length is 3m and is heated directly by an AC current. The test fluid is R-113. Experiment are carried out with mass flow rates of 300, 500 and $700\;kg/m^{2}s$, and heat fluxes varying from 5 to 65 kW/$m^2$. The inclination angles of the tube are $0^{\circ},\;5^{\circ},\;11^{\circ}\;and\;25^{\circ}$. the circumferential temperature variation at low quality region and the location of dryout at high quality region are mainly observed. Circumferential anisothermality occurring at low mass flow rate and low quality conditions is gradually reduced with the increase in the inclination angle and finally disappears at the inclination angle of $25^{\circ}$. Critical quality where dryout is initiated is seriously influenced by the inclination angle. Wall temperature after critical quality is also affected by the inclination angle.

• 소성∙가공
• /
• 제23권7호
• /
• pp.425-430
• /
• 2014

The aim of the current study was to predict the plastic deformation behavior of a heated slab during hot rough rolling. FE-simulations were performed to investigate the metal flow and to locate the position of surface material from the slab through the rough rolling and onto the strip, using a material point tracking technique. In addition, experimental hot rolling trials were conducted where artificial defects were impressed onto a heated slab in order to validate the FE-simulation results. The simulated results show the same tendency of deformation behavior as the experimental measurements. The movement of slab defects from the side surface towards the strip center is directly linked to the extent of lateral spread during the rolling.

• 한국지능시스템학회논문지
• /
• 제26권2호
• /
• pp.147-152
• /
• 2016

형상기억합금은 가열되거나 냉각될 때 모양과 강도가 변화하면서 큰 힘을 발생한다. 와이어 형태의 형상기억합금은 열을 가하면 길이가 축소되면서 상당히 큰 힘을 발휘하며, 소음없는 운동을 발생시킬 수 있으므로 모터를 대체할 수 있는 구동기로 활용가능하다. 이런 형상기억합금 구동기는 전기로 직접 가열할 수 있으며, 큰 범위의 운동을 만들어내는데 사용될 수 있다. 본 논문에서는 형상기억합금 구동기를 이용하여 3 개의 손가락을 가진 6 자유도의 로봇 손을 개발하고 제어하는 것에 대해 기술한다. 각 손가락은 2 개의 관절을 가지고 있으며, 각 관절은 길항(拮抗) 운동을 위해 서로 반대로 동작하는 두 개의 힘줄에 의해 구동된다. 부드러운 운동을 위한 충분한 힘을 만들어 내기 위해 각 힘줄은 2 개의 형상기억합금 구동기가 병렬로 구성된다. 형상기억합금 구동기를 가열하기 위한 전류를 제어하기 위해 PWM 드라이버를 채용하였으며, 실험을 통해 손가락의 길항 작용을 평가한다.

• 대한치과보철학회지
• /
• 제26권1호
• /
• pp.85-98
• /
• 1988

The primary aim of this study was to access the degree of marginal leakage in composite resin inlay restorations. Class V cavities were prepared on sixty extracted premolars. They were classified as control group and experimental group 1, 2 and each group was filled with BIS-FIL $I^{(R)}$ and $Silux^{(R)}$ composite resins. In the control group, the composite resin was inserted directly, the experimental group 2 was inserted as composite resin inlay after heat treatment on $125^{\circ}C$, 10 minutes. Then thermocycling was performed 1000 times. After staining with 1% Basic Fuchsin, they were cut in Buccolingual direction and the degree of penetration of the dye was examined under L/M. The following results were obtained : 1. In occlusal margin area, difference in marginal leakage was not observed in all groups. 2. In gingival margin area, cavities filled with composite resin inlay was less marginal leakage than filled directly in BIS-FIL $I^{(R)}$ group, and statistical significant difference was not existed in $Silux^{(R)}$ group. 3. The statistical significance was not existed between composite resin inlay and composite resin inlay heated secondarily. 4. In all groups, gingival margin area reveals more marginal leakage than occlusal margin area and statistical significance was existed.

• 산업과 과학
• /
• 제2권2호
• /
• pp.9-15
• /
• 2023

실리콘러버히터는 플렉시블하기 때문에 평면, 곡면, 입체적인 형태에서도 직접 접착이나 피가열물에 넣어 설치할 수 있다. 현재의 가열방식은 열이 필요하지 않은 영역 또는 위치를 무시하고 피가열물체 전체를 가열하여 필요한 온도로 상승시키기 때문에 일부분만을 부분집중 가열할 수 없었다. 멀티히팅존을 이용하면 피가열물체 전체를 가열하는 것보다는 공정에 따라 열이 필요한 부분만 집중가열하기 때문에 열이 필요한 장소마다 적은 전기용량으로 발열량을 다르게 적용하여 국소 위치별로 빠르게 가열할 수 있고, 열에너지를 줄일 수 있다. 본 연구에서는 열융착이 필요한 영역에서 균일한 온도 또는 온도 차이가 발생하도록 다중 가열영역 구조내의 부분집중 영역에 대한 온도 및 가열 시간을 측정한다. 최적의 전력밀도 범위 결정 및 전기용량을 감소하기 위해 멀티히팅존 구조로 제작된 실리콘러버히터의 안전성을 알아본다. 이와 같이 다중가열방식으로 실리콘러버히터를 제작하면 다중집중 가열기술을 모든 가열공정에 이상적으로 적용할 수 있다.

• 설비공학논문집
• /
• 제16권6호
• /
• pp.546-555
• /
• 2004

With circular tube heated directly or indirectly placed in a cross flow, heat flows circumferentially by conduction due to the asymmetric nature of the fluid flow around the perimeter of the circular tube. The circumferential heat flow affects the wall temperature distribution to such an extent that in some cases. The effects of circumferential wall heat conduction on local convective heat transfer is investigated. The wall heat conduction parameter which can be deduced from the governing energy equation should be used to express the effect of circumferential heat conduction. Two-dimensional temperature distribution is presented through the numerical analysis. The comparison of one-dimensional and two-dimensional solutions is demonstrated on graph of local Nusselt numbers.

• 한국공작기계학회:학술대회논문집
• /
• 한국공작기계학회 2002년도 춘계학술대회 논문집
• /
• pp.591-596
• /
• 2002

Fused deposition(FD) modeling by Stratasys Inc., is one of the material deposition subfamilies of solid freefrom fabrication(SFF) technologies. In this process, build material in the form of a flexible filament, is heated to a semi-liquid state and extruded from a controlled deposition head onto a fixtureless table in a temperature controlled environment. The position of nozzle is computer controlled relative to the base, which allows geometric complex models to be made to precise dimensions. FDM provide what the part was directly tested by the worker. It provide believable data. This Study is identify to surface roughness by build orientation adjustment. So, the paper is the study on surface roughness by build orientation at FDM.

• 한국공작기계학회:학술대회논문집
• /
• 한국공작기계학회 2001년도 추계학술대회(한국공작기계학회)
• /
• pp.387-392
• /
• 2001

Fused deposition(FD) modeling by Stratasys Inc., is one of the material deposition subfamilies of solid freeform fabrication(SFF) technologies. In this process, build material in the form of a flexible filament, is heated to a semi-liquid state and extruded from a robotically controlled deposition head onto a fixtureless table in a temperature controlled environment. The position of nozzle is computer controlled relative to the base, which allows geometric complex models to be made to precise dimensions. FDM provide what the part was directly tested by the worker. It provide believable data. This study is experiment on surface roughness of part at FDM