• Journal of the Korean Magnetics Society
• /
• v.5 no.3
• /
• pp.210-215
• /
• 1995

$Glass\Cr_{40\AA}\{[Cr_{10\AA}\NiFe_{50\AA}]}_N$ multilayers (number of layer N = 1, 2, 3, 4, 5, 6, 10) were made by dc magnetron sputtering under magnetic anisotropy of 200 G. Magnetoresistance curve MR(xx), MR(xy) were measured for the parallel and perpendicular current direction to external magnetic field. MR(xx) curves for the number of layer N=1, 5, 10 were almost became about zero percent, however the curves of other numbers appeared the phenomena of "positive magnetoresistance" that the resistance increased to external magnetic field, and the irregular and reversed curves in the vicinity of H=0 Oe.

• 한국방재학회:학술대회논문집
• /
• 2008.02a
• /
• pp.329-332
• /
• 2008

This study presents a viscoelastic characterization of flexible pavement subjected to moving loads. A series of field tests have been conducted on three pavement sections (A2, A5, and A8) at the Korea Expressway Corporation (KEC) test road. The effect of vehicle speed on the responses of each test section was investigated at three speeds: 25km/hr, 50km/hr, and 80km/hr. During the test, both longitudinal and lateral strains were measured at the bottom of asphalt layers and in-situ measurements were compared with the results of finite element (FE) analyses. A commercial FE package was used to model each test section and a step loading approximation has been adopted to simulate the effect a moving vehicle. Field responses reveal the strain anisotropy (i.e., discrepancy between longitudinal and lateral strains) and the amplitude of strain normally decreases as the vehicle speed increases. In most cases, lateral strain was smaller than the longitudinal strain, and strain reduction was more significant in lateral direction.

• Geotechnical Engineering
• /
• v.4 no.3
• /
• pp.35-42
• /
• 1988

A series of consolidated-undrained cubical triaxial tests was performed to investigate the three- dimensional strength characteristics of anisotropic overconsolidated clay. All specimens sampled in field were loaded under conditions of principal stress directions fixed and aligned with the directions during sampling. A sufficient number of tests It was performed to deter.mine the three- dimensional failure surface in the octahedral plane. The adjusted effective friction angles obtained by the stress state projected on the same octahedral plane did not show anisotropy, while the measured effective friction angles showed considerally difference according to the axes of speccimens. Therefore, Lade failure criterion proposed fort isotropic materials could be also used practically for anisotropic overconsolidated clay. The direction of the plastic strain increment wrectors superimposed on the principal stress space was nearly perpendicular to the traces of the failure surface in the octahedral plane.

• Tunnel and Underground Space
• /
• v.9 no.1
• /
• pp.56-63
• /
• 1999

Rock behaves in a complex way due to the discontinuities. To describe the complicated failure and deformation behavior of rock, many researches were focused on the development of crack models. This study discusses the validity of the sliding and shear crack model to systematically fractured rock, i.e. coal. The model was also implemented into a numerical analysis. For that, a finite element program was modified in several ways. To describe the transverse isotropy in two-dimensional analysis, the stress-strain relationship was modified for the direction of the axis of symmetry. Also, the changes of the effective elastic moduli according to the crack growth were calculated. A simple example of two-dimensional laboratory uniaxial compression test was analyzed. The results coincided with the observations obtained from the laboratory tests.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.33 no.7
• /
• pp.26-32
• /
• 2005

In this paper, the vibration response of the spacecraft solar array is investigated. The solar array model consists of composite thin walled beam and solar blanket, spreader bar. The composite thin walled beam incorporates a number of nonclassical effects of transverse shear, primary and secondary warping, rotary inertia and anisotropy of constituent materials. The solar blanket is a membrane subjected to uniform tension in the z direction. The spreader bar is a rigid member. A coupled thermal structure analysis that includes the effects of structural deformations on heating and temperature gradient is investigated. A stability criterion given in parameters for establishes the conditions for thermal flutter.

• Korean Journal of Crystallography
• /
• v.5 no.2
• /
• pp.93-99
• /
• 1994

Growth form and surface morphology of NYAB single crystal grown by TSSG technique using a K2O/3MoOS/0.5B203 flux was investigated. In the crystal grown from <100> or <120> seed, prismatic and (101) faces were well developed with different size each other. (001) face was also developed in the crystal grown from <001> seed. While growth hillocks were observed on the prismatic face of the crystal grown from <100> seed, surface striations parallel to neighbor (101) faces were formed on that face of the crystal grown from <001> seed. The (101) faces were grown by two dimensional nucleation growth. (001) face which was developed at slow growth velocity of [001] direction was grown by screw dislocation Anisotropy of growth velocity as to seed orientation affected on crystal morphology and surface morphology.

• Journal of the Korean Ceramic Society
• /
• v.25 no.3
• /
• pp.268-276
• /
• 1988

Ba or La-Substituted lead niobate $(Pb_{1-x}Ba_x)_{1-y}La_{2y/3}Nb_2O_6$(PBLN), powders having needle shape are prepared by flux method using KCl and the effect of Ba or La substitution on morphology of obtained powders is examined. From these needle shape powders, grain-oriented ceramics are made by doctor-blade method and two-stage hot-pressing technique. The dielectric, piezoelectric and optical properties of the ceramics are also investigaated. Heating condition and the amount of substituted Ba or La have remarkable effects have large anisotropy in both permittivity and coupling factor depending on the pressing direction.

• Journal of the Korean Magnetics Society
• /
• v.23 no.4
• /
• pp.122-125
• /
• 2013

Perpendicular magnetic anisotropy (PMA) is the phenomenon of magnetic thin film which is preferentially magnetized in a direction perpendicular to the film's plane. Amorphous multilayer with PMA has been studied as the good candidate to realization of high density STT-MRAM (Spin Transfer Torque-Magnetic Random Access Memory). The current issue of high density STT-MRAM is a decrease in the switching current of the device and an application of amorphous materials which are most suitable devices. The amorphous ferromagnetic material has low saturated magnetization, low coercivity and high thermal stability. In this study, we presented amorphous ferromagnetic multilayer that consists of an amorphous alloy CoSiB and a nonmagnetic material Pd. We investigated the change of PMA of the $[CoSiB\;t_{CoSiB}/Pd\;1.3nm]_5$ multilayer ($t_{CoSiB}$ = 0.1, 0.2, 0.3, 0.4, 0.5, 0.6 nm, and $t_{Pd}$ = 1.0, 1.1, 1.2, 1.3, 1.4, 1.5, 1.6 nm) and $[CoSiB\;0.3nm/Pd\;1.3nm]_n$ multilayer (n = 3, 5, 7, 9, 11, 13). This multilayer is measured by VSM (Vibrating Sample Magnetometer) and analyzed magnetic properties like a coercivity ($H_c$) and a magnetization ($M_s$). The coercivity in the $[CoSiB\;t_{CoSiB}\;nm/Pd\;1.3nm]_5$ multi-layers increased with increasing $t_{CoSiB}$ to reach a maximum at $t_{CoSiB}$ = 0.3 nm and then decreased for $t_{CoSiB}$ > 0.3 nm. The lowest saturated magnetization of $0.26emu/cm^3$ was obtained in the $[CoSiB\;0.3nm/Pd\;1.3nm]_3$ multilayer whereas the highest coercivity of 0.26 kOe was obtained in the $[CoSiB\;0.3nm/Pd\;1.3nm]_5$ mutilayer. Additional Pd layers did not contribute to the perpendicular magnetic anisotropy. The single domain structure evolved in to a striped multi-domain structure as the bilayer repetition number n was increased above 7 after which (n > 7) the hysteresis loops had a bow-tie shapes.

• Progress in Medical Physics
• /
• v.14 no.2
• /
• pp.81-89
• /
• 2003

The dose distributions of designed Ir-192 micro-source were investigated by dose computations which were accomplished by employing shape of encapsule material and thickness of the source for self-absorption. The computation dose derived from air-kerma rate (S$_{k}$ ) and dose rate constant (Λ) includes the anisotropy of dose distribution around the source. We got the dose rate constants in a water medium is 1.154 cGy h$^{-1}$ U$^{-1}$ . The size of the source was 0.5 mm in diameter and 3.5 mm in length and it was encapsuled in 1.1 mm$\Phi$${\times}$5.5 mm of stainless steel sealed with 0.3 mm of filter thickness. The tissue dose of reference point at 1.0 cm radial distance of the source axis was delivered 1.154 Uh$^{-1}$ (1.3167${\times}$10$^{-3}$ cGy/mCi-sec) from the S$_{k}$ 4.108U/mCi of Ir-192 source. The filtration effect contributed to air-kerma strength as exponential filtering effect of 86.2% in total attenuation, but self-absorption was 88.4% from radial dose distributions. In particular, the dose attenuations showed a rapid anisotropic distributions as 56% of reference dose along to $\pm$10 degrees from the tip of source axis and 50% for of that to source-cable direction. We persist in use the large diameter of applicator will avoid the dose anisotropy by the filtered attenuation effects along the axis of Ir-192 micro-source.

• Journal of the Korean Magnetics Society
• /
• v.6 no.5
• /
• pp.323-328
• /
• 1996

NiFe($60\;{\AA}$)/Cu($60\;{\AA}$)/Co($30\;{\AA}$) trilayers were formed on the $4^{\circ}$ tilt-cut Si(111) substrate by rf magnetron sputtering method. With a Cu($50\;{\AA}$) underlayer, NiFe($60\;{\AA}$)/Cu($60\;{\AA}$)/Co($30\;{\AA}$) trilayers developed in-plane magnebc anisotropy and in-plane perpendicular alignment of easy axes in two magnetic components of NiFe($60\;{\AA}$)/Cu($60\;{\AA}$)/Co($30\;{\AA}$) trilayers has been found. The easy axis of Co layer consisbng of NiFe($60\;{\AA}$)/Cu($60\;{\AA}$)/Co($30\;{\AA}$) trilayers turned out to be along $4^{\circ}$ tilt Si <112> direcbon and that of NiFe layer along Si <110> direction. [NiFe($60\;{\AA}$)/Cu($60\;{\AA}$)/Co($30\;{\AA}$)]/Cu($50\;{\AA}$)/Si(111, $4^{\circ}$ tiIt-cut) trilayers showed about 2.2 % MR ratio at room temperature and large plateau in MR curves, which are more improved MR characteristics than those in [NiFe($60\;{\AA}$)/Cu($60\;{\AA}$)/Co($30\;{\AA}$)]/Cu($50\;{\AA}$)/glass trilayers with no appreciable magnetic anisotropy.