• 대한기계학회논문집
• /
• 제16권6호
• /
• pp.1171-1178
• /
• 1992

본 연구에서는 직접접촉식 열교환기를 이용한 실험을 통하여 열교환기 설계에 가장 중요한 열교환기 단위 체적당 총괄 열전달 계수를 시스템의 작동조건에 따라 구 하여 실제 설계자료로 이용하는 데 그 목적이 있다.

• Nuclear Engineering and Technology
• /
• 제53권8호
• /
• pp.2464-2476
• /
• 2021

Direct-contact heat transfer of a single saturated droplet upon colliding with a heated wall in the regime of film boiling was experimentally investigated using high-resolution infrared thermometry technique. This technique provides transient local wall heat flux distributions during the entire collision period. In addition, various physical parameters relevant to the mechanistic modelling of these phenomena can be measured. The obtained results show that when single droplets dynamically collide with a heated surface during film boiling above the Leidenfrost point temperature, typically determined by droplet collision dynamics without considering thermal interactions, small spots of high heat flux due to localized wetting during the collision appear as increasing We_n. A systematic comparison revealed that existing theoretical models do not consider these observed physical phenomena and have lacks in accurately predicting the amount of direct-contact heat transfer. The necessity of developing an improved model to account for the effects of local wetting during the direct-contact heat transfer process is emphasized.

• 대한전자공학회:학술대회논문집
• /
• 대한전자공학회 1998년도 추계종합학술대회 논문집
• /
• pp.515-518
• /
• 1998

This paper describes a direct transfer method of multimedia data stream between multimedia processor and network device without using system memory. The hardware architecture and functions for direct transfer, the method to transfer multimedia data to and from the multimedia processor and etc are described. Comparing the proposed method with general methods, I show that the direct transfer method can decrease number of bus accesses and bus cycles.

• 설비공학논문집
• /
• 제3권3호
• /
• pp.153-160
• /
• 1991

Heat transfer characteristics of a direct contact heat exchanger utilizing sieve trays and spray nozzles for steam condensation for the purpose of combining with a LNG evaporator have been investigated with various cooling water flow rates and different vacuum pressures within the heat exchanger for the purpose of steam condensation. Temperature profiles and the volumetric overall heat transfer coefficients in a direct contact heat exchanger have been obtained for comparisons. The results show that the temperature differences between cooling water and steam along the direct contact heat exchanger height are rapidly decreasing and the volumetric overall heat transfer coefficients of the exchanger improves greatly as the inside vacuum pressure increases. The values of the overall heat transfer coefficients at P=-680mmHg have been increased significantly compared with at atmospheric pressure. At given pressure conditions, it is found that the values of average volumetric overall heat transfer coefficients for the sieve tray are found to be approximately 10% higher than those of the spray nozzle.

• Journal of Mechanical Science and Technology
• /
• 제16권3호
• /
• pp.344-353
• /
• 2002

A reliable computational heat transfer model has been investigated to define the heat transfer characteristics of a spray column direct contact heat exchanger, which is often utilized in the process involving counterflows for heat and mass transfer operations. Most of the previous studies investigated are one-dimensional unsteady solutions based on rather fragmentary experimental data. Development of a multidimensional numerical model and a computational algorithm are essential to analyze the inherent multidimensional characteristics of a direct contact heat exchanger. The present study has been carried out numerically and establishes a solid simulation algorithm for the operation of a direct contact heat exchanger. Operational and system parameters such as the speed and direction of working fluid droplets at the injection point, and the effects of aspect ratio and void fraction of continuous fluid are examined thoroughly as well to assess their influence on the performance of a spray column.

• Nuclear Engineering and Technology
• /
• 제33권6호
• /
• pp.585-595
• /
• 2001

A series of experiments have been carried out to investigate the effects of non-condensable gas on the direct contact film condensation of vapor mixture under an adiabatic wall condition. The average heat transfer coefficient of the direct contact condensation was obtained at the atmospheric pressure with four main parameters ; air-mass fraction, mixture velocity, film Reynolds number, and the degree of water film subcooling having an influence on the condensation heat transfer coefficient. With the analysis of 88 experiments, a correlation of the average Nusselt number for direct contact film condensation of steam/air mixture at an adiabatic vertical wall was proposed as functions of film Reynolds number, mixture Reynolds number, air mass fraction, and Jacob number. The average heat transfer coefficient for steam/air mixture condensation decreased significantly while air mass fraction increased. The average heat transfer coefficients also decreased as the Jacob number increased, and were scarcely affected by the film Reynolds number below a mixture Reynolds number of about 245,000.

• 한국수정란이식학회지
• /
• 제12권1호
• /
• pp.67-74
• /
• 1997

This study was carried out to increase the viability of bovine frozen4hawed in vitro produced (IVP) embryos and pregnancy rate by direct transfer method. Cumulus-oocyte complexes were aspirated from excised Hanwoo ovaries and matured in TGM 199 for 20~22 hours at 38.5$^{\circ}C$ in 2% $CO_2$ in air. Matured oocytes were fertilized with capacitated sperm for 6 hours and then co-cultured with cumulus cells for 9 days. 63% of the oocytes cultured was deaved and 29% out of them developed into blastocysts. Good or excellent grade of blastocysts on D 7 or 8 were frozen with 1.8M ethylene glycol as a cryoprotectant for direct transfer. Frozen embryos were thawed at 2$0^{\circ}C$ water for 10 sec following 4~5 second in air. For the survival assay of frozen4hawed lVP blastocysts, they were cultured in TCM 199 supplemented with 100$\mu$M $\beta$-mercaptoethanol and 20% FCS for 72 hours. The percentage of embryos developed to re-expanded or hatched after 72 hours culture was 95. 5 and 77.3%, respectively. When frozen-thawed Ivp embryos were transferred to 43 synchronized recipients by direct transfer method, eighteen recipients (41.8%) was pregnant. The highest pregnant was in naturafly synchronized recipients (71.4%), but induced estrus by using PRID(29.2%) and PGF$_2$$\alpha$(20.0%) was showed lower pregnancy rate. The pregnancy rate was higher in day 7 blastocysts(56.0%) than day 8 blastocysts(22.2%). (Key words: in vitro produced, blastocyst, frozen-thawed, direct transfer)

• 조명전기설비학회논문지
• /
• 제27권10호
• /
• pp.15-20
• /
• 2013

In this paper, wireless power transfer system using the magnetic resonance was designed and applied to LED lighting for implementation of wireless lighting. This lighting was made by the converted DC driving type and the direct AC driving type. In the former, transferred AC power was rectified into DC and regulated to the specified voltage value, which leads to produce the loss at the rectifying and regulating circuit. In the latter, wireless-transferred AC power was directly applied to LED, which get rid of the loss derived from the additional circuit. For the efficiency-comparison between the former and the latter, the power at each stage was measured when the same optical output radiated from LED lighting part. The result revealed that the direct AC driving type had 18% higher efficiency than the DC driving type and confirmed that LED lighting using magnetic resonance wireless power transfer system can be efficient by direct AC power supply. And the direct AC driving type had the simple circuit structure and the simple LED lighting formation, so this can leads to various application.

• 대한설비공학회:학술대회논문집
• /
• 대한설비공학회 2008년도 하계학술발표대회 논문집
• /
• pp.1161-1166
• /
• 2008

The objective of this research was to investigate the enhancement of heat transfer by mesh in water/air direct contact air conditioning system. Mesh is inserted as a turbulent promoter in front of the water injection nozzle. The heat transfer characteristics with and without mesh and the effect of the number of inserted mesh and mesh porosity size have been studied experimentally. Inserted mesh improves heat transfer efficiency compared to non-inserted mesh system and heat transfer efficiency increased as the number of mesh is increased. Meanwhile, heat transfer efficiency decreased as the porosity of the mesh is increased. With inserted mesh, inlet and outlet temperature difference of air increased more than 50%. Heat exchange time of water/air to reach the 100% humidity decreased less than 30%. This result shows inserted mesh can enhance the performance of the water/air direct contact air conditioning system.

• 설비공학논문집
• /
• 제20권1호
• /
• pp.75-80
• /
• 2008

The objective of this research was to investigate the enhancement of heat transfer by mesh in water/air direct contact air conditioning system. Mesh is inserted as a turbulent promoter in front of the water injection nozzle. The heat transfer characteristics with and without mesh and the effect of the number of inserted mesh and mesh porosity size have been studied experimentally. Inserted mesh improves heat transfer efficiency compared to non~inserted mesh system and heat transfer efficiency increased as the number of mesh is increased. Meanwhile, heat transfer efficiency decreased as the porosity of the mesh is increased. With inserted mesh, inlet and outlet temperature difference of air increased more than 50%. Heat exchange time of water/air to reach the 100% humidity decreased less than 30%. This result shows inserted mesh can enhance the performance of the water/air direct contact air conditioning system.