• 동력기계공학회지
• /
• 제9권2호
• /
• pp.81-87
• /
• 2005

This study is numerical analysis on the increasing temperature characteristics of vaporizer fin for liquefied natural gas with super low temperature. Existing LNG vaporizers use the direct contact heat transfer mode where the extreme super low temperature LNG of $-162^{\circ}C$ flows inside of the tubes and about $20^{\circ}C$air flows on outside of the fin. Recently, the vaporizers with great enhanced performance compared to conventional type have been developed to fulfill these requirements. The vaporizing characteristic of LNG vaporizer with air as heat source has a fixed iced. These characteristic cause a low efficiency in vaporizer, total plant cost and installing space can be increased. The vaporizing characteristics of LNG via heat exchanger with air are analytically studied for an air heating type vaporizer. This study is intended to supply the design data for the domestic fabrication of the thickness and angle vaporizer fin. Governing conservation equations for mass, momentum and energy are solved by STAR-CD based on an finite volume method and SIMPLE algorithm. Calculation parameter is fin thickness, setup angle and LNG temperature. If the vaporization performance of the early stage and late stage of operating is considered, the case of ${\phi}=90^{\circ}$ was very suitable. In this paper was estimated that the heat transfer was most promoted in case of THF=2mm.

• 대한기계학회논문집B
• /
• 제33권9호
• /
• pp.709-717
• /
• 2009

Heat transfer rate is a very important factor for the performance of a steam reformer because a steam reforming reaction is an endothermic reaction. Coaxial cylindrical reactor is the reactor design which can improve the heat transfer rate. Temperature, fuel conversion and heat flux in the coaxial cylindrical steam reformer are studied in this paper using numerical method under various operating conditions. Langmuir-Hinshelwood model and pseudo-homogeneous model are incorporated for the catalytic surface reaction. Dominant chemical reactions are assumed as a Steam Reforming (SR) reaction, a Water-Gas Shift (WGS) reaction, and a Direct Steam Reforming (DSR) reaction. Although coaxial cylindrical steam reformer uses 33% less amount of catalyst than cylindrical steam reformer, its fuel conversion is increased 10 % more and its temperature is also high as about 30 degree. There is no heat transfer limitation near the inlet area at coaxial-type reactor. However, pressure drop of the coaxial cylindrical reactor is 10 times higher than that of cylindrical reactor. Operating parameters of coaxial cylindrical steam reformer are the wall temperature, the inlet temperature, and the Gas Hourly Space Velocity (GHSV). When the wall temperature is high, the temperature and the fuel conversion are increased due to the high heat transfer rate. The fuel conversion rate is increased with the high inlet temperature. However, temperature drop clearly occurs near the inlet area since an endothermic reaction is active due to the high inlet temperature. When GHSV is increased, the fuel conversion is decreased because of the heat transfer limitation and short residence time.

• Advances in nano research
• /
• 제6권3호
• /
• pp.243-255
• /
• 2018

Polystyrene granules were combined with nanosilver to form a nanocomposite film. One-side migration was conducted to test into three food simulants (3% acetic acid, 10% ethanol and 95% ethanol) at $40^{\circ}C$ temperature on different period of time (2, 4, 6, 8 and 10 days). It was found that, among the simulants, the highest migration amount was obtained with 3% acetic acid, while the 95% ethanol revealed the least migration level. Diffusion coefficients of nanosilver particles into simulants were estimated by inverse simulation using experimental data of concentration variation in the simulants. The finite element method used to solve the mass transfer equation and the numerical results indicates the sameresponse with the experimental data. The numerical results confirmed that the highest diffusion coefficient for acetic acid 3% (1.82E-10 to $1.76E-9m^2\;s^{-1}$) and the lowest diffusion coefficient for ethanol 95% from 2 to 10 days were obtained, respectively. Also, results of diffusion coefficient - concentration relation showed, the diffusion coefficient had in direct correlation with time and concentration. The results indicated that, in the 3% acetic acid, due to the increasing of diffusion coefficient of silver nanoparticles, they are released faster and distributed uniformly.

• 한국지반공학회논문집
• /
• 제20권4호
• /
• pp.29-38
• /
• 2004

본 연구에서는 복합 경계면요소를 이용한 비선형 응력-변형 모델을 이용하여 쓰레기 매립지의 안정성해석을 수행하였다. 쓰레기 매립층의 응력-변형 거동 특성은 국내외 쓰레기의 삼축압축 강도시험 수행결과로써 결정하였고, 경계면 요소의 모델 변수 값은 여러 가지 차수재의 전단시험 결과를 적용하였다. 해석방법에 대한 검증을 위하여 국내 페기물 관리법에 준하는 매립지 모델을 선정하여 안정성해석을 실시하였다. 쓰레기에 대한 삼축압축시험과 토목섬유재에 대한 응력-변형 특성을 분석한 결과 쓰레기는 선형거동을 그리고 토목섬유는 비선형거동을 나타내는 것으로 나타났다. 경계면요소를 이용한 복합차수층 매립지의 안정성 해석결과 매립지 바닥면과 사면의 경계부에서 응력집중과 차수계의 전단변위가 크게 나타나 토목섬유라이너가 포설된 복합차수층의 경우는 복합 경계면 요소가 적용된 해석이 필요함을 알 수 있었다.

• 한국측량학회지
• /
• 제27권4호
• /
• pp.437-444
• /
• 2009

동역학적 방법을 이용한 GPS(Global Positioning System) 위성궤도 결정을 위해 양방향 적분이 가능한 multi-step 방식의 수치적분기를 개발하였으며, 이는 GPS 위성 고도에서 마이크로미터 수준의 정확도를 보였다. 가속도 모델링에서 달, 태양 이외의 천체에 의한 인력은 매우 작으므로 태양복사압에서 경험적 모델로 대체하였다. 위성궤도 미지수는 수치적분된 위성궤도와 IGS(International GNSS Service) 정밀궤도를 이용하여 최소제곱방법으로 결정했다. 이를 위해서는 수치적분기에서 가속도와 함께 미지수에 대한 편미분값을 동시에 적분해야 한다. 추정된 위성궤도 미지수를 이용하여 계산한 잔차의 RMS(Root Mean Squares error)로 부터 위성궤도의 정확도를 검증했다. 2009년 3월 한달의 평균적인 궤도오차 RMS는 5.2mm 였으며, 궤도오차의 절대적인 크기는 위성체의 종류 및 위성진행방향기준 좌표계 상에서 특별히 편향된 형태를 보이지는 않는 것으로 나타났다. 본 연구에서 적용한 태양복사압 모델은 상수항 및 궤도당 1주기에 대한 변화만을 포함하고 있으므로, 궤도당 2주기에 해당하는 궤도오차 양상을 크게 보이고 있으며 이에 대한 추가적인 연구가 필요할 것으로 판단된다.

• 한국지진공학회논문집
• /
• 제19권1호
• /
• pp.29-36
• /
• 2015

Base isolation is considered as a seismic protective system in the design of next generation Nuclear Power Plants (NPPs). If seismic isolation devices are installed in nuclear power plants then the safety under a seismic load of the power plant may be improved. However, with respect to some equipment, seismic risk may increase because displacement may become greater than before the installation of a seismic isolation device. Therefore, it is estimated to be necessary to select equipment in which the seismic risk increases due to an increase in the displacement by the installation of a seismic isolation device, and to perform research on the seismic performance of each piece of equipment. In this study, modified NRC-BNL benchmark models were used for seismic analysis. The numerical models include representations of isolation devices. In order to validate the numerical piping system model and to define the failure mode, a quasi-static loading test was conducted on the piping components before the analysis procedures. The fragility analysis was performed by using the results of the inelastic seismic response analysis. Inelastic seismic response analysis was carried out by using the shell finite element model of a piping system considering internal pressure. The implicit method was used for the direct integration time history analysis. In addition, the collapse load point was used for the failure mode for the fragility analysis.

• Structural Engineering and Mechanics
• /
• 제12권6호
• /
• pp.657-668
• /
• 2001

Fiber reinforced cementitious composites are nowadays widely applied in civil engineering. The postcracking performance of this material depends on the interaction between a steel fiber, which is obliquely across a crack, and its surrounding matrix. While the partly debonded steel fiber is subjected to pulling out from the matrix and simultaneously subjected to transverse force, it may be modelled as a Bernoulli-Euler beam partly supported on an elastic foundation with non-linearly varying modulus. The fiber bridging the crack may be cut into two parts to simplify the problem (Leung and Li 1992). To obtain the transverse displacement at the cut end of the fiber (Fig. 1), it is convenient to directly solve the corresponding differential equation. At the first glance, it is a classical beam on foundation problem. However, the differential equation is not analytically solvable due to the non-linear distribution of the foundation stiffness. Moreover, since the second order deformation effect is included, the boundary conditions become complex and hence conventional numerical tools such as the spline or difference methods may not be sufficient. In this study, moment equilibrium is the basis for formulation of the fundamental differential equation for the beam (Timoshenko 1956). For the cantilever part of the beam, direct integration is performed. For the non-linearly supported part, a transformation is carried out to reduce the higher order differential equation into one order simultaneous equations. The Runge-Kutta technique is employed for the solution within the boundary domain. Finally, multi-dimensional optimization approaches are carefully tested and applied to find the boundary values that are of interest. The numerical solution procedure is demonstrated to be stable and convergent.

• 한국정보통신학회:학술대회논문집
• /
• 한국해양정보통신학회 2005년도 추계종합학술대회
• /
• pp.677-680
• /
• 2005

유체의 상변화를 이용하는 냉난방장치 등의 열장치에 대한 열역학적인 성능평가는 열역학적 성질들에 대한 구체적인 수치값을 필요로 한다. 그러나 이러한 열역학적 성질들을 제공하는 증기표를 그대로는 사용할 수 없기 때문에 효과적인 모델링이 필요하다. 본 연구에서는 신경회로망의 함수근사 특성을 이용하여 냉방장치의 매질로 사용되는 냉매(R12)의 포화증기 영역을 모델링하였다. 냉매 R12의 포화증기 영역의 함수근사 해석을 위하여 1개의 노드를 가진 입력층에 대하여 7개의 노드를 가진 출력층을 기본으로 하여, 각각 10개와 20개의 노드를 가진 두 개의 은닉층을 가진 회로망을 구성하였다. 또한 입력이 온도와 압력 두 가지의 경우에 대하여 검토하였다. 제안된 신경회로망을 사용한 결과 엔탈피, 엔트로피의 백분율오차가 대부분 ${\pm}$0.005%, 비체적은 ${\pm}$0.02%, 압력과 온도는 특별한 몇 개를 제외하고는 ${\pm}$0.02% 범위 내로 수렴되었다. 이 결과로부터 냉매를 함수근사하는데 있어서 신경회로망이 아주 강력한 수단이 될 수 있음을 확인하였다.

• 수산해양기술연구
• /
• 제23권3호
• /
• pp.1-1
• /
• 1987

이상으로부터 다음의 결론을 얻는다. 조파저항 이론의 전개에서 Michell 적분보다 더욱 정밀한 Neumann-Kelvin 문제가 복잡한 kernel 함수 때문에 많은 시간과 노력이 필요하지만, 원점 부근에서 Kelvin 소오스의 점근거동을 조사하여 세장체 근사를 행함으로 N-K 문제의 kernel 함수에 대한 근사와 동등하게 처리될 수 있었다. 조파저항의 계산 결과가 Michell 적분과 비슷한 경향을 보이나, 실험치와의 정확한 비교를 할 수 없었다. 그러나 세장선 이론을 적용함으로써 훨씬 복잡하고 지루한 작업을 들 수 있었다. 전진 속도를 갖는 경우에는 수정된 Green정리를 이용하면 될 것으로 기대된다.

• 대기
• /
• 제32권4호
• /
• pp.341-351
• /
• 2022

Recently, interest in the possibility of a washout effect using artificial rain enhancement technology to reduce high-concentration fine dust is growing. Therefore, in this study, the reduction rate of PM₁₀ concentration according to the amount of artificial rain enhancement was calculated during Asian Dust event which occurred over the Korean Peninsula on March 29, 2021 using air quality model [i.e., Community Multiscale Air Quality (CMAQ)] combined with the mesoscale model for artificial rain enhancement (i.e., WRF-MMS). According to WRF-MMS, the washout effect lasted 5 hours, and the maximum precipitation rate was calculated to be 1.5 mm hr^-1. According the CMAQ results, the PM₁₀ reduction rate was up to 22%, and the affected area was calculated to be 6.4 times greater than that of the artificial rain enhancement area. Even if the maximum amount of precipitation per hour is lowered to 0.8 mm hr^-1 (about 50% level), the PM₁₀ reduction rate appears to be up to 16%. In other words, it is believed that this technique can be used as a direct method for reducing high-concentration fine dust even when the artificial rain enhancement effect is weak.