• Korean Journal of Optics and Photonics
• /
• v.8 no.3
• /
• pp.245-249
• /
• 1997

An electro-optic polymer digital optical switch with a coupling region modified for optimum coupling is designed and demonstrated. Its branch waveguide is fabricated by reactive ion etching. Then, the modified coupling region is adiabatically introduced along the propagation direction from the branching point of the two waveguides, and it is implemented by photobleaching after the device fabrication. The structure of the modified coupling region and its refractive index profiles are designed to optimize and mode coupling in the Y-branch waveguide. Therefore, the switching performance of the device was shown to be enhanced with a fixed device length. The measured drive voltage is reduced by more than 30 percents, and the crosstalk is also improved by about 4~6 dB.

• The Journal of the Institute of Internet, Broadcasting and Communication
• /
• v.24 no.3
• /
• pp.109-114
• /
• 2024

The effect of inter-channel coupling in multi-channel monopulse receiver is expected to increase by miniaturization trend of receiver. Therefore, in this paper, calibration method is proposed to compensation for inter-channel coupling in receiver of monopulse radar. And it can prevent distortion of angle information of target. Hardware configuration that consists of switch, directional coupler, matched load, ADC(Analog to Digital Converter), signal source of calibration is proposed to calibration. Total nine scattering parameters are obtained by controlling the switch and signal source of calibration. After that, method for restoring the undistorted signal is proposed using the mathematical relationship between the monopulse signal output from the antenna and the monopulse signal passing through the multi-channel receiver in the presence of inter-channel coupling.

• The Transactions of the Korean Institute of Electrical Engineers D
• /
• v.55 no.5
• /
• pp.229-235
• /
• 2006

High speed PC-based DIO(Digital I/O) system that consists of a master device and slave I/O devices is developed. The PCI interfaced master device controls all of serial communications, reducing the load on the CPU to a minimum. The slave device is connected from the master device and another slave device is connected to the slave device, it can repeated to maximum 64 slave devices. The slave device has 3 types I/O mode, such as 16 bits input-only, 16 bits output-only, and 8bits input-output. The master device has 2 rings which can take 64 slaves each. Therefore, total I/O points covered by the master is 2048 points. The slave features 3 types of input/output function interchangeability by DIP switch settings. Library, application, and device driver software for the DIO system that have a secure and a convenient functionality are developed.

• Proceedings of the KWS Conference
• /
• 2000.04a
• /
• pp.99-102
• /
• 2000

Conventionally, ZVS FB DC/DC converter was controlled by monolithic IC UC3879, which includes the functions of oscillator, error amplifier and phase-shift circuit. Also, microprocessor and DSP have been widely used for the remote control and for the immediate waveform control in ZVS FB DC/DC converter. However the conventional microprocessor controller is complex and difficult to control because the controller consists of analog and digital parts. In the case of the control of FB DC/DC converter, the output is required of driving a direct signal to the switch drive circuits by the digital controller. So, this paper presents the method and realization of designing the digital-to-phase shift PWM circuit controlled by DSP (TMX320C32) in a 2,500A, 40㎾ WS FB DC/DC converter.

• Journal of The Korean Digital Architecture Interior Association
• /
• v.12 no.4
• /
• pp.5-12
• /
• 2012

In this study, a digital design process by utilizing the program's database functionality in BIM, public education facilities master plan presented an alternative model to the layout of the design process. First of all, public education facilities master plan design process with digital design process and how to use the database of BIM in the process for review of the possibility of. Secondly, public educational facility planning the placement as needed for the switch to digital design limits, and the basic plan design at various elementary school planning alternatives in a school building and the school site is required to investigate. Thirdly, as a way of using the database features of GDL BIM lnn and teachers on how to create a variable by setting up a number of different alternatives so that you can choose the architect thought to have to organize and visualize the possibility of quick. A quantitative way the basic plan design that repeats some of the measures that can be used for digital design change as a process of continuous research is needed.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.29 no.3
• /
• pp.141-146
• /
• 2016

The AMR(automatic meter reading) system has been increasingly and widely used for its efficient and intelligent management, which is a technology that automatically collects consumption data from a water meter or energy metering device. The digital meter instead of the mechanical meter should be used in the system. Up to now, various types of sensor to measure the water flow rate have been used in the digital water meter, for example, reed switch, photo IR approximate sensor, ultrasonic sensor, electromagnetic sensor, etc. In this paper, a new sensing technology, where a variable capacitor and digital circuit were used for sensing the water flow rate, was proposed. The circuit was designed and verified by Pspice simulation. And a PCB board for the circuit was fabricated. After then, a prototype of digital water meter using a variable capacitor to measure the water flow rate was fabricated. The function tests of the fabricated digital water meter were performed, and it was found that the meter worked properly. Since the new technology has much better properties in terms of cost and power consumption compared to conventional technologies, it should be one of the major digital water meter technologies in the future.

• Proceedings of the IEEK Conference
• /
• 2004.06b
• /
• pp.545-548
• /
• 2004

The paper describes the design of high-speed, high-resolution Sample-and-Hold circuit which shows the conversion rate 80MHz and the power supply of 3.3v with 0.35um CMOS 2-poly 4-metal process for high-speed, high resolution Analog-to-Digital Converter. For improving Dynamic performance of Sample-and-Hold, Two Double bootstrap switch and high performance operational amplifier with gain booster, which are used. and For physical stability of Sample and Hold circuit, reduces excess voltage of gate in bootstrap switch. Simulation results using HSPICE shows the SFDR of 71dB, 75dB in conversion rate of 80MHz result for two inputs(0.5Vpp, 10MHz and 1Vpp, 10MHz) and the power dissipation of 48mW at single 3.3V supply voltage.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 1998.11a
• /
• pp.472-482
• /
• 1998

오늘날의 통신서비스들은 음성이나 데이터 서비스와 같은 전통적인 서비스 뿐만 아니라 비디오 서비스와 같은 대량의 데이터를 전송해야만 하는 멀티미디어 서비스를 포함한다. 이러한 요구를 수용하기 위해서 BISDN(Broadband Integated Digital Network)이 개발되었고 이의 기반 기술로 ATM이 채택되었다. 다양한 멀티미디어 응용들 중에서 VOD(Video On Demand), 화상회의 등은 데이터를 동시에 여러 목적지로 보내는 멀티캐스트 특성이 있다. 그러므로 멀티캐스트 능력은 멀티미디어 통신에서 매우 중요하다. 본 논문에서는 링망을 이용한 병렬 멀티캐스트 패킷스위치(Parallel Multicast Packet Switch with Ring Network: PMRN)에서의 분리된 HOL을 이용한 멀티캐스트 셀 스케줄링 기법을 제안한다. 이 기법은 입력버퍼의 앞단에 멀티캐스트 셀과 유니캐스트 셀을 위한 분리된 HOL을 두고 non-FIFO방식을 사용함으로서 입력버퍼 내에서 전송 가능한 멀티캐스트 셀과 유니캐스트 셀을 동시에 스케쥴링할 수 있도록 하여 입력버퍼 내에서의 지연을 감소시키고 링망과 일대일 연결 네트워크의 이용율을 높이며 스위치의 처리율을 높일 수 있다.

• Proceedings of the IEEK Conference
• /
• 2002.07c
• /
• pp.1390-1393
• /
• 2002

Comparative analysis of driving inverters for piezo-electric transformer (PT) is performed and the suit- able drive circuit for portable devices such as personal digital assistants (PDA) is chosen with the experiment in this paper. As a result, a single-switch inverter with a small two winding reactor is chosen, and then the advantages of this method are clarified. It is also confirmed that the driving inverter with this method enables to realize a stabilized AC 400v output and 82% power efficiency from DC 3V input under the conditions of the variations of load current or input voltage from the experiments. Piezo-electric Transformer, Back-Light System, Single-Switch Driving Circuits, Control Method

• The Transactions of the Korea Information Processing Society
• /
• v.7 no.3
• /
• pp.901-908
• /
• 2000

Satellite communication in the 21 century's high tech information world is developing rapidly, marked by high levels of applications and functions. For example, satellite communication can process and switch the speed of the service provided by a broad and vast digital multimedia system such as a long-distance all between nations or broadcasting transfer service, which is supplied by a contemporary satellite system. So, it bring about problems which lack of satellite orbit and gibes out frequency resource by increment of satellite universally. To support this, an OBP satellite system is need, which includes an on-board IF/RF switch, baseband signal processing, multi-beam antenna technology, as well as a simple transponder system. In this paper, we have outlined the next generation of satellite communication; satellite OBP transport network architecture, which offers multimedia service and applied frequency reuse method for multi-spot beam. The satellite B-ISDN transport network architecture is also analyzed.