• Proceedings of the IEEK Conference
• /
• 2005.11a
• /
• pp.411-414
• /
• 2005

The most recent trend on digital hearing aid is to increase the ratio of signal to noise by directivity or to develop noise reduction algorithm inside DSP IC chip. This paper designed, fabricated and tested a digital hearing aid directivity testing device in which a micro-mouse-like the stepping motor with a speaker rotates around an examinant. Both ears of the examinant were fixed with ITE hearing aids in order to response to receiving sound. The diameter of the directivity testing device was 2 [m] and the micro-mouse was precisely controlled by PICBASIC micro processor.

• Proceedings of the KIEE Conference
• /
• 1999.11c
• /
• pp.652-654
• /
• 1999

This paper presents approaches to the control of the DVD(Digital Video Disk) system using DSP(Digital Signal Processor) in order to improve the precision and robustness. To improve the performance of the Pick-Up servo actuator of the digital video drive, the tracking and focusing servo control algorithms is applied to this system. Simulation results show the performance of the robust control algorithm applied the pick-up servo system comparing to the linear controller.

• Journal of IKEEE
• /
• v.22 no.3
• /
• pp.619-623
• /
• 2018

Due to the development of society, the demand for electric power has increased and the quality control of electric power has become an important issue. In order to efficiently perform such power management, we propose a DSP based power measurement system for multi-wire power measurement. Since the conventional power measurement system can measure only the power of one line, a power quality measurement device is required for each line in order to measure the power quality of the individual line. Respectively. The system proposed in this paper proposes a system capable of real-time measurement of power quality at up to 12 points using digital signal processing algorithm, and the prototype based on this system was evaluated through the official test report of Korea Electrotechnology Research Institute. As a result of the performance test, it was evaluated that the error range is excellent at ${\pm}0.3%$.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.47 no.7
• /
• pp.78-86
• /
• 2010

This paper discusses the programming model of SODA-II that is a baseband processor for software defined radio (SDR) systems. Signal processing On-Demand Architecture Ⅱ (SODA-II) is an on-chip multiprocessor architecture consisting of four processor cores and each core has both an wide SIMD datapath and a scalar datapath. This architecture is appropriate for baseband processing that is a mixture of vector computations and scalar computations. The programming model of the SODA-II is based on C library routines. Because the library routines hide the details of complex SIMD datapath control procedures, end users can easily program the SODA-II without deep understanding on its architecture. In this paper, we discuss the details of library routines and how these routines are exploited in the implementation of baseband signal processing algorithms. As application examples, we show the implementation result of W-CDMA multipath searcher and OFDM demodulator on the SODA-II.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2009.10a
• /
• pp.153-156
• /
• 2009

The interferometric fiber optic gyroscopes (FOGs) are well known as sensors of rotation, which are based on Sagnac effect, and have been under development for a number of years to meet a wide range of performance requirements. This paper describes the development of open-loop FOG and digital signal processing techniques implemented on FPGA. Our primary goal was to obtain intermediate accuracy (pointing grade) with a good bias stability ($0.22^{\circ}/hr$) and scale factor stability, extremely low angle random walk ($0.07^{\circ}/\sqrt{hr}$) and significant cost savings by using a single mode fiber. A secondary goal is to design all digital FOG signal processing algorithms with which the SNR at the digital demodulator output is enhanced substantially due to processing gain. The CIC type of decimation block only requires adders and shift registers, low cost processors which has low computing power still can used in this all digital FOG processor.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.16 no.11
• /
• pp.2011-2020
• /
• 1992

This paper discusses about real time control applying sliding mode to robot manipulators whose nonlinear terms, which are inertia term, Corilis term and centrifugal force mterm, are regarded as disturbances. We could simplify the dynamic equations of a manipulator and servo system, which are composed of linear elements and nonlinear elements, by assuming that non-linear terms are external disturbance. By simplifying that equation, we could easily obtain a control input which satisfy sliding mode. We proposed a new control input algorithm to decrease chattering in the application of sliding mode control of manipulator whose nonlinear elements are regarded as disturbances. We could take impulse response of linear elements of dynamic equations of a robot manipulator and servo system by Signal Compression Method. So then, we could obtain the unknown parametes of its linear lements, which are used to obtain switching parameter satisfying sliding mode, by Signal Compression Method. In this experiments, we used DSP(Digital Signal Processor) controller to suppress chattering by obtaining a switching speed and to carry out real time control.

• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.25 no.2
• /
• pp.113-119
• /
• 2011

A frequency in electrical power system changes by the load fluctuation in utility grid, has an influence on a connected generator, and ultimately brings a big trouble in the power system. Therefore, a quick measurement of system frequency and governor control of power system is a very important factor in the reliability and the economic feasibility. Electromagnetic frequency relays in the past had the large power consumption and the difficulty of accurate measurement. After Researched and developed digital relays are very affected by the noise and the distortion, and the recently developed Microprocessor relays have problems of expensive device and time when measuring the frequency at 50[ms]. In this study, An improve algorithm that measures the power system frequency quickly and accurately is suggested, simulated by using Matlab and programmed using C code through DSP6713 KIT. This algorithm is tested to the arbitrary voltage waveform input. The results show that the suggested algorithm is effective in the accurate and quick frequency measurements.

• Journal of the Korean Institute of Telematics and Electronics B
• /
• v.31B no.10
• /
• pp.21-31
• /
• 1994

This paper describes the multichannel combined R2MFC/DTMF/CCT reciver which provides a signaling service functions for call processing control in digital switching system. Using the TMS320C25 DSP chip, we have implemented multi-function receriver shich processes 8 channels of R2MFC, DTMF, and CCT signals simultaneously. In order to increase the channel multiplicity of the combined receiver. R2MFC and CCT receiver were employed by discrete Fourier transform(DFT) method using Goertzel algorithm, and DTMFreceiver was employ by infinite impulse reponse(IIR) filtering method using 4KHz subsampling technique. The combined receiver has 4 function modes for each channel such as R2MFC, DTMF, CCT, and Idle modes. The function mode of each channel may be selected at any time by single-chip micro-controller(.mu.C). Hence, the number of channels assigned for each function mode can be adjusted dynamically according to the signaling traffic variations. From the experimental test results using the test-bed, it has been proved that the combined receiver statisfies all receiver satisfies all receiver specifications, and provides good channel multiplicity and performance, Therefore, it may give a great improvement than existing receiver in cost, reliability, availability, and serviceability.

• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.18 no.4
• /
• pp.124-130
• /
• 2004

In this paper, we developed DSP(Digital Signal Processor)-based control system to automatically open and close passive filter, which is used to reduce harmonics, according to operating condition of loads. Passive filter control system automatically open and close each branch of filter according to working conditions of loads by sending signals to open and close installation of passive filter after measuring and monitoring voltage, current, harmonics, reactive power, power factor and so on. We verified it's performance by connecting control system with passive filter in the power line using the 100HP D.C motor drive, opening and closing passive filter according to operation condition of motor, and measuring harmonics and reactive power, etc.

• Journal of the Institute of Electronics Engineers of Korea SC
• /
• v.40 no.4
• /
• pp.225-234
• /
• 2003

Turbo compressors need high speed rotating impeller in structure, high rate gearbox and conventional induction motor. This mechanical system increased moment of inertia and mechanical friction loss. Recently turbo compressor has adopted a super high-speed motor and driver and have made its size smaller and mechanical friction loss at minimum. In this paper, variable super high - speed motor controller, compressor controller and MMI controller are implemented with only one DSP (TMS320VC33) chip for a 150HP, 70,000rpm direct drive turbo compressor. It was required hardware and software integration. The result of integration, Controller hardware became simple and all control software are developed same developing tool. The implements turbo compressor meets the requirements.