• Proceedings of the Korean Vacuum Society Conference
• /
• 2014.02a
• /
• pp.188.1-188.1
• /
• 2014

Aluminum is widely used as a material for electrode on silicon based devices. Especially, aluminum films are used as backside and front-side electrodes in silicon quantum dot (QD) solar cells. In this point, the diffusion of aluminum is very important for the enhancement of power conversion efficiency by improvement of contact property. Aluminum was deposited on a Si (100) wafer and a Si QD layer by ion beam sputter system with a DC ion gun. The Si QD layer was fabricated by $1100^{\circ}C$ annealing of the $SiO_2/SiO_1$ multilayer film grown by ion beam sputtering deposition. Cs ion beam with a low energy and a grazing incidence angle was used in SIMS depth profiling analysis to obtain high depth resolution. Diffusion behavior of aluminum in the Al/Si and Al/Si QD interfaces was investigated by secondary ion mass spectrometry (SIMS) as a function of heat treatment temperature. It was found that aluminum is diffused into Si substrate at $450^{\circ}C$. In this presentation, the effect of heat treatment temperature and Si nitride diffusion barrier on the diffusion of Al will be discussed.

• Transactions on Electrical and Electronic Materials
• /
• v.16 no.4
• /
• pp.201-205
• /
• 2015

This paper dealt with the condensing technology of an LED light source that uses a parabolic reflector to replace a searchlight equipped with a xenon lamp. A ray-tracing simulation was conducted to analyze the influence of the diameter of the reflector and the size of the light source on light condensing. The combination of a parabolic reflector with a diameter of 620 mm and a focal distance of 220 mm, and a 9 mm multi-chip package (MCP) with a luminous flux of 7,000 lm showed the narrowest beam angle. The luminous intensity at the center was measured at 7.7×10⁶ cd. The distance between the light source and the point where the illuminance was 1 lx was calculated to be 2.8 km. The power consumption of the system was 95 W, which is only 9.5% of that of the 1 kW xenon searchlight, and the beam angle was 1.03°. In a site experiment, it was confirmed that the light ray reflected from the LED searchlight proceeds forward without any diffusion because of the narrow beam angle.

• Journal of Korea Multimedia Society
• /
• v.8 no.10
• /
• pp.1360-1368
• /
• 2005

PDP is the flat panel display, suitable for high definition television because of large-sire and high-brightness. It has many advantages such as fast response, wide viewing angle, low weight, and simple manufacturing process for fabrication. However, there are some disadvantages and one of them is the image quality degradation, which is dependent on the digital signal processing. Although image quality of PDP is improving by many researches and experimentations, it still isn't as good as that of CRT because of various factors. One of them is worm-like pattern generated by an error diffusion process. And the worm-like pattern is severely increased after an APL process. An increased worm-like pattern occur a drop of resolution in image and a change of CCT according to each grayscale. In this paper, a method for improvement of image quality using the error diffusion which considers the APL process is proposed. In the proposed method, the APL process is performed before the error diffusion process. Simulation results showed that the proposed method has better performances for resolution in images and CCT uniformity according to each grayscale than the conventional method.

• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.27 no.8
• /
• pp.1-8
• /
• 2013

The study carried out in this dissertation focuses on the lens structure design and the light distribution for LED safety luminaires using COB type LED module. Lens structures for LED lights has been designed 1) to induce light diffusion by dual process of internal reflection and refraction, 2) to minimize the inherent LED lights' glittering, and 3) to have uniform brightness. The lens designed with the proposed structures function as diffusers for the divergence of the LED lights so that they form a wide angle of view and adjust the light distribution. We designed of lens with stable uniformity factor and average roughness using aspheric optics property. Finally we made the analysis data of the simulated data.

• Journal of the Korean Institute of Telematics and Electronics D
• /
• v.36D no.1
• /
• pp.83-89
• /
• 1999

A Unified model for the alpha-particle-induced charge collection has been developed. By accounting for funneling and diffusion charges separately, new model accurately describes the dependence of collected charge on junction size, junction bias, injection energy, injection angle, injection point, and trench oxide depth.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2008.11a
• /
• pp.378-379
• /
• 2008

Recently, composite hollow bushings have been increasingly employed mainly from the various characteristics. Composite bushings are superior to porcelain bushings in several respects, including lighter weight, better anti-pollution and anti-explosion properties, and easer manufacturing. Filament wound GRP tubes which have various winding angle were manufactured by using a filament winding machine. This paper will show some design issues and winding condition for composite bushing. And, results show that the winding condition of composite GRP tubes can be used to improved their bending strength and pressure, For bending and pressure tested, tubes with the hybrid winding pattern show higher strength than those of unit winding pattern. Also, the influence of absorption was evaluated through such as measurement of the dye penetration test and water diffusion test, also aspects of surface state using scanning electron microscopy.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.64 no.2
• /
• pp.310-314
• /
• 2015

To improve the optical performance of the backlight unit with light guide plate(LGP), we investigated the effects of LGP patterns on the brightness and viewing angles properties of the backlight unit. We designed several patterns of LGP and calculated their optical properties by the optical simulation. The results reveal that the highest brightness and wide viewing angle was achieved with the extended-closed-polygon diffusion pattern and upper triangle prism pattern of the LGP.

• Journal of the Microelectronics and Packaging Society
• /
• v.5 no.2
• /
• pp.37-48
• /
• 1998

The popcorn cracking phenomena in plastic IC packages during reflow soldering are investigated by considering the heat transfer and moisture diffusion through the epoxy molding compound(EMC) along with the mechanics of interface delamination. Heat transfer and moisture diffusion through EMC under die pad are analyzed by finite difference method (FDM)during the pre-conditioning and subsequent reflow soldiering pro-cess and the amounts of moisture mass and vapor pressure at delaminated die pad/ EMC interface are calculated as a function of the reflow soldering time. The energy release rate stress intensity factor and phase angle were obtained under various loading conditions which are thermal crack face vapor pressure and mixed loadings. It was shown that thermal loading was the main driving force for the crack propagation for small crack lengths but vapor pressure loading played more significant role as crack grew.

• Proceedings of the Optical Society of Korea Conference
• /
• 2009.10a
• /
• pp.103-104
• /
• 2009

We proposed the laminate thin film asymmetric Extruded-closed-polygon diffusion pattern that was able to improve the performance of back light unit. Developed a pattern of brightness and bright line, half-power angle attribute the improved performance in the uniform, and through the formation of a thin film stackable diffusion layer 970% improved perpendicularity brightness, and 580% improved horizontality brightness.

• Journal of the Korean Ceramic Society
• /
• v.32 no.10
• /
• pp.1117-1122
• /
• 1995

The effect of grain boundary structure on zigzag migrtion has been studied. Five kinds of a(2110)-m(1010) diffusion couples with different twist angles by 30$^{\circ}$from a [0001] common direction of each plane were prepared. When chromia (Cr2O3) was added to the diffusion couples by a vapor phase, zigzag migration of the grain boundary occurred. The fraction of zigzag migration did not essentially vary with the twist angle, but the magnitude and migration distance of individual migrating segment varied. The variation of CIGM morphology thus appears to result from the change in grain boundary mobility due to microscopic deviation of grain boundary structure out of a macroscopic grain boundary orientation.