• Transactions on Electrical and Electronic Materials
• /
• v.14 no.3
• /
• pp.156-159
• /
• 2013

The electrical properties of ZnO nanowire field effect transistors (FETs) have been investigated depending on various diameters of nanowires. The ZnO nanowires were synthesized with an Au catalyst on c-plane $Al_2O_3$ substrates using hot-walled pulsed laser deposition (HW-PLD). The nanowire FETs are fabricated by conventional photo-lithography. The diameter of ZnO nanowires is simply controlled by changing the thickness of the Au catalyst metal, which is confirmed by FE-SEM. It has been clearly observed that the ZnO nanowires showed different diameters simply depending on the thickness of the Au catalyst. As the diameter of ZnO nanowires increased, the threshold voltage of ZnO nanowires shifted to the negative direction systematically. The results are attributed to the difference of conductive layer in the nanowires with different diameters of nanowires, which is simply controlled by changing the catalyst thickness. The results show the possibility for the simple method of the fabrication of nanowire logic circuits using enhanced and depleted mode.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2008.06a
• /
• pp.535-536
• /
• 2008

Multi-layered thin films of ZnS/$Na_3AlF_6$/ZnS/Cr were deposited on glass substrate by evaporation process. ZnS and $Na_3AlF_6$ were selected as high and low refractive index material, and additionally Cr was chosen as mid reflective layer respectively. The multi-layered thin films were prepared in terms of different optical thickness and different staking sequence and layers. The optical properties were systematically characterized with different optical thickness of $Na_3AlF_6$ especially $0.25\lambda$ and $0.5\lambda$. In order to expect the experimental result, the simulation program, the Essential Macleod Program(EMP) was adopted. Based on the results taken by spectrophotometer at viewing angle $45^{\circ}$, the ZnS/$Na_3AlF_6$/ZnS/Cr multi-layered thin film shows purple colour range in $0.25\lambda$， bluish green in $0.5\lambda$, red purple in $0.75\lambda$, and purple in $1.0\lambda$ respectively.

• Transactions on Electrical and Electronic Materials
• /
• v.2 no.3
• /
• pp.28-32
• /
• 2001

It was studied in the present work how the thermal cycling performance of LOC (lead on chip) packages depends on the package construct or leadframe materials. First, package body thickness and Au wire diameter were manipulated for the selection of proper package design. Secondly, two different types of leadframe materials (i.e. copper and 52%Fe-48%Ni alloy) were tested to determine the better material for improved reliability margin of plastically encapsulated microelectronic packages. This work shows that manipulating package body thickness was more effective than an increase of Au wire from 23$\mu\textrm{m}$ to 33$\mu\textrm{m}$ for the prevention of wire debonding failure. Further, this work indicates that the LOC packages including the copper leadframes can be more susceptible to thermal cycling reliability degradation due to chip cracking than those including the alloy leadframes.

• Korean Journal of Materials Research
• /
• v.25 no.8
• /
• pp.417-422
• /
• 2015

In this study, low-carbon hypoeutectoid steels with different ferrite-pearlite microstructures were fabricated by varying transformation temperature. The microstructural factors such as pearlite fraction and interlamellar spacing, and cementite thickness were quantitatively measured and then Charpy impact tests conducted on the specimens in order to investigate the correlation of the microstructural factors with impact toughness and ductile-brittle transition temperature. The microstructural analysis results showed that the pearlite interlamellar spacing and cementite thickness decreases while the pearlite fraction increases as the transformation temperature decreases. Although the specimens with higher pearlite fractions have low absorbed energy, on the other hand, the absorbed energy is higher in room temperature than in low temperature. The upper-shelf energy slightly increases with decreasing the pearlite interlamellar spacing. However, the ductile-brittle transition temperature is hardly affected by the pearlite interlamellar spacing because there is an optimum interlamellar spacing dependent on lamellar ferrite and cementite thickness and because the increase in pearlite fraction and the decrease in interlamellar spacing with decreasing transformation temperature have a contradictory role on absorbed energy.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2012.08a
• /
• pp.162-162
• /
• 2012

ZnPc and CuPc molecules stacked similar way in the film, but showed different growth modes in thermal evaporation. The distribution of CuPc crystals did not change by the film thickness, whereas the distribution of ZnPc became random as the increase of the film thickness. The disc type nanograins of CuPc were quite regularly distributed at the initial growth regime and the regular distribution of nanograins was kept during the film growth. On the other hand, ZnPc consisted in ellipsoid shaped nanograins and the distribution of nanograins was not regular in the initial growth regime. The irregular distribution of nanograins changed to the regular mode at the later growth regime by showing structure factor in GISAXS measurement. The different initial nanograin distribution in ZnPc and CuPc was related to the different nanostructure in the mixed layer with C60 to form the bulk heterojunction.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2006.11a
• /
• pp.66-66
• /
• 2006

Development of ArF Photo-lithography process has proceeded with the increase of numerical aperature (NA) and the decrease of resist thickness. It makes many problems such as cost and process complexity. A novel spin-on hard mask system is proposed to overcome many problems Spin-on hard mask composed of two layers of siloxane and carbon. The optical thickness of two layers is designed from reflectivity measurement at specified n, k respectively. The property of photo-resist shows different results according to Si contents. Si-contents was measured XPS(X-ray Photoelectron spectroscopy).

• Journal of the Korean institute of surface engineering
• /
• v.54 no.4
• /
• pp.171-177
• /
• 2021

This paper is concerned with the surface hardness measurement of NiP-coated AA7050 using different loads from 10 to 100 g. The surface hardness was observed to increase from 180 to 600 H_v with increasing NiP layer thickness, depending on the load applied for indentation. When NiP coating thickness is thinner than 2 ㎛, the surface hardness of NiP-coated AA7050 was mainly determined by AA7050 substrate, while it was significantly increased by NiP coating layer when NiP coating thickness is thicker than 2 ㎛. Hardness of AA7050 substrate itself was not dependent on the applied load but the hardness of NiP-coated AA7050 was largely influenced by the load applied for indentation. The largest difference of hardness between 10 g and 100g of applied loads, was obtained at the NiP thickness of about 8 ㎛ above which the measured hardness at 10 g reached a maximum value of about 600 H_v. It was also observed that indentation-induced plastic deformation next to the indented zone occurs when NiP layer is 5.64 times thicker than the depth of impression formed by indentation.

• Transactions of Materials Processing
• /
• v.21 no.1
• /
• pp.49-57
• /
• 2012

It is difficult to estimate the properties of multilayered sheet because they are composed of one or more different materials. Plastic deformation behavior of the multilayered sheet is quite different as compared to each material individually. The deformation behavior of multilayered sheet should be investigated in order to prevent forming defects and to predict the properties of the formed part. In this study, the mechanical properties and formability of stainless steel-aluminum-magnesium multilayered sheet were investigated. The multilayered sheet needs to be deformed at an elevated temperature because of its poor formability at room temperature. Uniaxial tensile tests were performed at various temperatures and strain rates. Fracture patterns changed mainly at a temperature of $200^{\circ}C$. Uniform and total elongation of multilayered sheet increased to values greater than those of each material when deformed at $250^{\circ}C$. The limiting drawing ratio (LDR) was obtained using a circular cup deep drawing test to measure the formability of the multilayered sheet. A maximum value for the LDR of about 2 was achieved at $250^{\circ}C$, which is the appropriate forming temperature for the Mg alloy. Fracture patterns on a circular cup and thickness of formed part were predicted by a rigid-viscoplastic FEM analysis. Two kinds of modeling techniques were used to simulate deep drawing process of multilayered sheet. A single-layer FE-model, which combines the three different layers into a macroscopic single layer, predicted well the thickness distribution of the drawn cup. In contrast, the location and the time of fracture were estimated better with a multi-layer FE model, which used different material properties for each of the three layers.

• Proceedings of the Korean Powder Metallurgy Institute Conference
• /
• 2006.09a
• /
• pp.85-86
• /
• 2006

A theoretical model is applied to the analysis of thermomechanical properties of $Al-SiC_p$ FGMs in this study. Functionally graded $Al-SiC_p$ composites ($Al-SiC_p$ FGMs) consisted with 10 layers gradually changing volume fractions of Al and $SiC_p$ were fabricated using the pressureless infiltration technique. $Al-SiC_p$ FGMs plates of total thickness of 3mm, 5mm and 7mm with fairly uniform distribution and compositional gradient of $SiC_p$ reinforcement in the Al matrix throughout the thickness was successfully fabricated. The curvature of $Al-SiC_p$ FGM plates was measured to check the internal stress distribution predicted via a theoretical model for the analysis of thermo-mechanical deformation. The evolution of curvature and also internal stresses in response to temperature variations could be predicted for the different combinations of geometric thickness of FGM plates. Theoretical prediction of thermally induced stress distribution makes it possible to design FGM structures without any critical failure during the usage of them.

• Smart Structures and Systems
• /
• v.32 no.2
• /
• pp.123-133
• /
• 2023

This paper proposes a thermography-based coating thickness estimation method for steel structures using model-agnostic meta-learning. In the proposed method, a halogen lamp generates heat energy on the coating surface of a steel structure, and the resulting heat responses are measured using an infrared (IR) camera. The measured heat responses are then analyzed using model-agnostic meta-learning to estimate the coating thickness, which is visualized throughout the inspection surface of the steel structure. Current coating thickness estimation methods rely on point measurement and their inspection area is limited to a single point, whereas the proposed method can inspect a larger area with higher accuracy. In contrast to previous ANN-based methods, which require a large amount of data for training and validation, the proposed method can estimate the coating thickness using only 10- pixel points for each material. In addition, the proposed model has broader applicability than previous methods, allowing it to be applied to various materials after meta-training. The performance of the proposed method was validated using laboratory-scale and field tests with different coating materials; the results demonstrated that the error of the proposed method was less than 5% when estimating coating thicknesses ranging from 40 to 500 ㎛.