• Geomechanics and Engineering
• /
• 제23권5호
• /
• pp.467-480
• /
• 2020

The failure behavior and tensile strength of sandstone materials under different strain rates are greatly different, especially under static loads and impact loads. In order to clearly investigate the failure mechanism of sandstone materials under static and impact loads, a series of Brazilian disc samples were used by employing green sandstone, red sandstone and black sandstone to carry out static and impact loading splitting tensile tests, and the failure properties subjected to two different loading conditions were analyzed and discussed. Subsequently, the failure behavior of sandstone materials also were simulated by finite element code. The good agreement between simulation results and experimental results can obtain the following significantly conclusions: (1) The relationship of the tensile strength among sandstone materials is that green sandstone < red sandstone < black sandstone, and the variation of the tensile sensitivity of sandstone materials is that green sandstone > red sandstone > black sandstone; (2) The mainly cause for the difference of dynamic tensile strength of sandstone materials is that the strength of crystal particles in sandstone material, and the tensile strength of sandstone is proportional to the fractal dimension; (3) The dynamic failure behavior of sandstone is greatly different from that of static failure behavior, and the dynamic tensile failure rate in dynamic failure behavior is about 54.92%.

• The Journal of Advanced Prosthodontics
• /
• 제14권5호
• /
• pp.305-314
• /
• 2022

PURPOSE. The aim of this study was to evaluate the flexural strength of a 3D-printed denture base resin (Cosmos Denture), after different immediate repair techniques with surface treatments and thermocycling. MATERIALS AND METHODS. Rectangular 3D-printed denture base resin (Cosmos Denture) specimens (N = 130) were thermocycled (5,000 cycles, 5℃ and 55℃) before and after the different repair techniques (n = 10 per group) using an autopolymerized acrylic resin (Jet, J) or a hard relining resin (Soft Confort, SC), and different surface treatments: Jet resin monomer for 180 s (MMA), blasting with aluminum oxide (JAT) or erbium: yttrium-aluminum-garnet laser (L). The control group were intact specimens. A three-point flexural strength test was performed, and data (MPa) were analyzed by ANOVA and Games-Howell post hoc test (α = 0.05). Each failure was observed and classified through stereomicroscope images and the surface treatments were viewed by scanning electron microscope (SEM). RESULTS. Control group showed the highest mean of flexural strength, statistically different from the other groups (P < .001), followed by MMA+J group. The groups with L treatment were statistically similar to the MMA groups (P > .05). The JAT+J group was better than the SC and JAT+SC groups (P < .05), but similar to the other groups (P > .05). Adhesive failures were most observed in JAT groups, especially when repaired with SC. The SEM images showed surface changes for all treatments, except JAT alone. CONCLUSION. Denture bases fabricated with 3D-printed resin should be preferably repaired with MMA+J. SC and JAT+SC showed the worst results. Blasting impaired the adhesion of the SC resin.

• Tribology and Lubricants
• /
• 제25권1호
• /
• pp.61-65
• /
• 2009

Tribological properties of the semi-metallic friction materials containing different solid lubricants (graphite, $WS_2$, $MoS_2$) were investigated. The friction materials were fabricated with an experimental formulation and tested with gray cast iron disks. Results showed that graphite contributed to stabilize the friction coefficient during run-in processes. Also, graphite provided better fade resistance than that of $WS_2$ and $MoS_2$. At intermediate temperature ranges, however, friction materials with $WS_2$ or $MoS_2$ maintained higher friction effectiveness than that of graphite. On the other hand, friction materials containing $MoS_2$ showed increased wear rates than that with graphite or $WS_2$. Friction materials with proper combinations of two solid lubricants showed better friction and wear properties than that of the friction materials containing single solid lubricant.

• 한국복합재료학회:학술대회논문집
• /
• 한국복합재료학회 2004년도 추계학술발표대회 논문집
• /
• pp.135-138
• /
• 2004

Because the compressive properties such as compressive stiffness and compressive maximum strength of the fabric composite materials are essential to analyse the drape behaviour and estimate the quality of the final products, compressive tests of fabric composites with different stacking sequences were performed. Appropriate shape and dimensions for the compressive test specimens were prepared and several specimens with different conditions were tested and compared with each other.

• 한국분말야금학회:학술대회논문집
• /
• 한국분말야금학회 2006년도 Extended Abstracts of 2006 POWDER METALLURGY World Congress Part2
• /
• pp.987-988
• /
• 2006

The processes of P/M affect the properties of sintered gears. The different techniques of P/M lead to the different properties of sintered gears. This paper summarizes new progress in powder metallurgy for sintered gears. These progresses include warm compaction, high velocity compaction, sinter hardening, high temperature sintering, infiltration, CNC powder press and surface densification etc.

• Tribology and Lubricants
• /
• 제21권2호
• /
• pp.77-82
• /
• 2005

In previous paper, the wear properties of clutch facing materials with two different copper amounts against fly-wheel materials used in the clutch system were investigated by sliding wear tests at different applied loads and speeds. This paper have been aimed to evaluate the friction properties for clutch facing materials at the same test conditions as the previous paper. The experimental results indicated that the friction properties of clutch facing materials are influenced from the thermal conductivities of the clutch facing material and the counter material. The clutch facing material with the lower thermal conductivity and the fly-wheel material with the higher thermal conductivity showed the low and stable friction coefficient in the range of high sliding speed. This appears to be due to the formation of a film on the surface of the fly-wheel material.

• 한국정보디스플레이학회:학술대회논문집
• /
• 한국정보디스플레이학회 2006년도 6th International Meeting on Information Display
• /
• pp.1090-1092
• /
• 2006

There is provided white light illumination system including a radiation source, a first luminescent material having a peak emission wavelength of about 575 to about 620 nm, a second luminescent material having a peak emission wavelength of about 495 to about 550 nm, which is different from the first luminescent material and a third luminescent material having a peak emission wavelength of about 420 to about 480 nm, which is different from the first and second luminescent materials. The LED may be a UV LED and the luminescent materials may be a blend of three phosphors. A human observer perceives the combination of the blue, green and red phosphor emissions as white light.

• 한국정보디스플레이학회:학술대회논문집
• /
• 한국정보디스플레이학회 2003년도 International Meeting on Information Display
• /
• pp.818-821
• /
• 2003

Sn-doped $In_{2}O_{3}$ (ITO) thin film is one of the materials widely on research not only in the academic fields but also in industrial fields because of their transparency, high conductivity and good adhesion characteristics on substrate. ITO thin films are usually preferred oriented to one of the (222), (400), and (440) planes during crystallization process, which is dependent on processing variables. The preferred orientation affects electrical, optical and etching properties of the films. In this study, thin films of preferred oriented in different orientation were fabricated by controlling processing variables. The crystallization behavior, grain size, surface roughness, transparency and electrical properties of the thin films in different orientation were examined.

• Current Research on Agriculture and Life Sciences
• /
• 제31권1호
• /
• pp.11-17
• /
• 2013

To investigate the effects of co-solvents on the morphology of nano-scale zein materials, zein solutions were electrospun with different co-solvent ratios of EtOH/$H_2O$. Different zein solution concentrations were used to study the effects of the zein content on the electrospun materials. The resulting electrospun materials were all characterized using field-emission scanning electron microscopy (FE-SEM) and transmission electron microscopy (TEM). The diameters of the electrospun nanoparticles and nanofibers were found to increase when increasing the EtOH ratio at certain zein concentrations. Furthermore, increasing the zein content changed the morphology of the electrospun materials from nanoparticles to nanofibers.

• 한국토양비료학회지
• /
• 제47권3호
• /
• pp.179-186
• /
• 2014

Weathering indexes of the typical pedons derived from different parent materials of the soils of Korea were calculated by Kronberg and Nesbitt (1981) to understand weathering degree of the soils which might give a clue of soil formation and characterizing a soil pedon. The weathering index W1 was chemical change index, and the weathering index W2 was silicate dominant index. The chemical compositions of the 49 typic pedons were extracted from the Taxonomical Classification of Korean Soils (NIAST, 1999). The weathering indexes of Kimhae series, derived from fluvio marine material, were the highest among the analyzed soils. Within parent materials, the weathering indexes of the soils derived from limestones parent materials were high, and those derived from phorphyry materials were low. The relationship between W1 and W2 showed unique pattern which implied certain sequence within the same parent materials.