• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 2007년도 추계학술대회 논문집
• /
• pp.84-86
• /
• 2007

Aluminum sheets were asymmetrically cold rolled without lubrication by using different roll velocities of upper and lower rolls in order to intensify the shear deformation. During asymmetrical cold rolling of aluminum sheets, a reduction per a rolling pass, initial sheet thickness, roll diameter, roll velocity ratio were varied to investigate the effect of rolling parameters. The formation of through thickness shear texture was related to the ratio of the contact length between the roll and sample($l_c$) to the sheet thickness(d). The strain states associated with asymmetrical rolling were investigated by the finite element method (FEM) simulation. FEM results indicated that the evolution of deformation texture in a thickness layer is strongly governed by integrated values of strain rates $\dot{\varepsilon}_{13}$ and $\dot{\varepsilon}_{11}$ along the streamline in the roll gap.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2004년도 춘계학술대회
• /
• pp.192-197
• /
• 2004

The anisotropy in coefficient of thermal expansion (CTE) between the in-plane and out-of-plane of 3-dimensional thick composite structures induces residual stresses and the large void content due to insufficient compaction of fabric composites, which results in low interlaminar strengths. In order to reduce the through thickness CTE and the void content, in this work, carbon fabric phenolic laminates were compacted by pressure generated by autoclave and a compressive jig, from which the through-thickness CTEs and the void contents were measured. From the measurement, it was found that the through-thickness CTE and the void content had different characteristics from ordinary composites due to gas produced during the cure reaction of phenolic resin.

• 설비공학논문집
• /
• 제21권11호
• /
• pp.629-635
• /
• 2009

In this study, fin surface temperature and frost properties, i.e., frost thickness and frost surface temperature on a heat exchanger, were experimentally analyzed with different fin thicknesses, fin sizes and thermal conductivities of fin. As a result, it is found that fin thickness and thermal conductivity of fin should be considered in order to design an efficient heat exchanger fin. Correlations of dimensionless average frost properties were proposed as functions of dimensionless air temperature, dimensionless fin base temperature, dimensionless fin thickness, absolute air humidity, Reynolds number and Fourier number. The correlations predicted well the average frost thickness with a maximum error of 10.5% and frost surface temperature with a maximum difference of $0.89^{\circ}C$, respectively.

• 한국생물물리학회:학술대회논문집
• /
• 한국생물물리학회 1999년도 학술발표회 진행표 및 논문초록
• /
• pp.56-56
• /
• 1999

Change of membrane property can affect the activity of membrane proteins. In this work, we investigated the single channel properties of large conductance $Ca^{2+}$-activated $K^{+}$(BK) channels in planar lipid bilayers of different thickness. First, we recorded the activity of single BK channels from rat skeletal muscle incorporated into the control bilayer, then increased the bilayer thickness by perfusing the recording solution with the one saturated with n-pentane, or reduced the thickness by adding diheptanoylphosphatidylcholine (di$C_{7:0}$PC) to the recording soluton.(omitted)

• 한국콘크리트학회:학술대회논문집
• /
• 한국콘크리트학회 2004년도 추계 학술발표회 제16권2호
• /
• pp.789-792
• /
• 2004

This study aims to detect only voids and estimate the cross-sectional size and thickness of voids using radar. A new method based on radar image processing is carried out with various void sizes and depths. The regression relationship between void size which has different depth and the amplitude characteristics of the radar return is considered in a new method of this research. For the purpose of examining; this regression relationship, experiments with change of void depth, surface area and thickness were carried out. Finally, the threshold value for image processing which aims to represent only voids to be fitted size (width) can be obtained. As the results, a proposed method in this study has a possibility of detecting only voids and estimating void size and thickness with good accuracy.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2005년도 추계학술대회 논문집 전기기기 및 에너지변환시스템부문
• /
• pp.95-97
• /
• 2005

Loss in the multi-stacked HTS wires are affected by a number of factor, such as, number of wires used in the stack, direction of external magnetic field and insulation thickness between the wire. This paper examines the effects of the insulation thickness on the magnetization loss of the multi-stacked YBCO coated conductor. Measurements of magnetization loss were performed using 4 different typo of multi-stacked wires and under various angle of external magnetic field. Test results show that loss density per unit volume increased for YBCO coated conductors when thickness of insulation increased. Loss density per unit volume decreased for YBCO coaled conductors when stacking number of tapes increased.

• 한국의류학회지
• /
• 제28권8호
• /
• pp.1057-1064
• /
• 2004

Silk, polyester, cotton, and wool fabrics were embroidered with varying stitch length of 3mm, 5mm, and 10mm to examine the difference in fabric shrinkage in terms of sewing direction, fabric thickness, cover factor, stitch length, and fiber type. Warp, filling, and bias direction of sewing resulted in no difference in fabric shrinkage. Within the samples with same stitch length, there was less fabric shrinkage in fabrics with higher fabric thickness or higher cover factor. There was larger shrinkage when sewn with longer stitch length. Comparing fabrics with different fiber types but similar fabric thickness, silk and polyester fabrics showed the smallest fabric shrinkage and wool fabrics showed the largest shrinkage. It is shown that similar fabric shrinkage between silk and polyester is due to the similarity in cover factor.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2005년도 하계학술대회 논문집 Vol.6
• /
• pp.93-94
• /
• 2005

Cu metallization using electrochemical plating(ECP) has played an important role in back end of line(BEOL) interconnect formation. In this work, we studied the optimized copper thickness using Bottom-up Gap-fill in Cu ECP, which is closely related with the pattern dependencies in Cu ECP and Cu dual damascene process at 0.13 ${\mu}m$ technology node. In order to select an optimized Cu ECP thickness, we examined Cu ECP bulge, Cu CMP dishing and electrical properties of via hole and line trench over dual damascene patterned wafers split into different ECP Cu thickness.

• 농업과학연구
• /
• 제50권4호
• /
• pp.595-602
• /
• 2023

Feed processing methods can substantially enhance the nutrient value of feed. The aim of our study was to compare the effects of mash or crumble feed on growth performance, nutrient digestibility, back-fat thickness, and carcass quality of growing-finishing pigs. In total, 50 ([Landrace × Yorkshire] × Duroc) growing pigs with initial body weight of 46.24 ± 3.57 kg were randomly assigned to two dietary treatment groups. The two dietary treatments were: 1) mash and 2) crumble feed forms for 14 weeks of trials. Five replication pens per treatment, comprised five pigs (2 males and 3 females) each. Growth performance, nutrient digestibility, back-fat thickness, and carcass quality were observed at different weeks. There were no significant differences in growth performance, nutrient digestibility, back-fat thickness, and carcass quality throughout the experimental trial. Further study is required to understand the effects of mash and crumble feed on growing-finishing pigs.

• 한국콘크리트학회:학술대회논문집
• /
• 한국콘크리트학회 2002년도 봄 학술발표회 논문집
• /
• pp.935-940
• /
• 2002

This paper presents the failure mode on Headed Bars and prediction of tensile capacity, which is governed by concrete cone failure. 17 different plate types, three different concrete strengths and three different welding types of specimens were simulated. Static tensile load was applied Headed Bars were manufactured in different areas, and their shape and thickness are based on ASTM 970-98. Calculation of embedment length in concrete is conducted based on CSA 23.3-94, and static tensile load was applied. Tested pullout capacities were compared to the values determined using current design methods such as ACI-349 and CCD method.