• International Journal of Automotive Technology
• /
• v.7 no.3
• /
• pp.237-244
• /
• 2006

Limited and nonlimited emissions of scooters were analysed during several annual research programs of the Swiss Agency of Environment Forests and Landscape(SAEFL, BUWAL). Small scooters, which are very much used in the congested centers of several cities are a remarkable source of air pollution. Therefore every effort to reduce the emissions is an important contribution to improve the air quality in urban centers. In the present work detailed investigations of particle emissions of different 2-stroke scooters with direct injection and with carburetor were performed. The nanoparticulate emissions with different lube oils and fuels were measured by means of SMPS, (CPC) and NanoMet. Also the particle mass emission(PM) was measured with the same method as for Diesel engines. It can be stated, that the oil and fuel quality have a considerable influence on the particle emissions, which are mainly oil condensates. The engine technology influences the (nano)particle emissions by: mixture preparation, mixture tuning, oil consumption, postoxidation, quality, condition and temperature of the catalyst. Since the particulate emission of the 2-S consists mainly of lube oil condensates the minimization of oil consumption stays always an important goal.

• 한국생물공학회:학술대회논문집
• /
• 2000.11a
• /
• pp.435-438
• /
• 2000

Crude oil-degrading microorganisms, Acinetobacter sp. A132, Pseudomonas aeruginosa F722, and Acinetobacter calcoaceticus OM1 were isolated from soil and sea. The optimal temperature of strain A132 and strain F722 on growth isolated from soil was $35^{\circ}C$ both, and also their growth were optimized at pH 8 and 9, respectively. The growth of the strains, A132 and F722, showed that crude oil of 2% (w/v) in culture broth in which crude oil was used as carbon and energy sources appeared to be an optimum. Optimal culture conditions of strain OM1 were different from those of the soil microorganisms except for temperature. The growth of strain OM1 was optimized at pH 7 and crude oil of 3.0% (w/v). The degradability to crude oil by strain A132 showed maximum $5.49g/\;l\;{\cdot}\;day$ under the conditions of $25^{\circ}C$, NaCl of 1.0% (w/v), and crude oil of 2.0% (w/v). The highest degradability of strain F722 to crude oil was $1.19g/\;l\;{\cdot}\;day$ under the culture conditions at $35^{\circ}C$, NaCl 1.0% (w/v), and crude oil of 2.0% (w/v). The degradation characteristics of kerosene $(nC_9-nC_{20})$ and diesel $(nC_9-nC_{28})$ by strain OM1, and F722 were analyzed by gas chromatography. Strain OM1 degraded more than 95% of kerosene and 75% of diesel for 7 days cultivation. Strain F722 showed degradation of more than 80% to kerosene in 10 days.

• Journal of Korean Society of Environmental Engineers
• /
• v.36 no.7
• /
• pp.476-482
• /
• 2014

In this study, the characteristics of emulsified fuel and engine emissions were studied with engine dynamometer. Microexplosion took place in the combustion chamber. While combustion, emulsion fuel scattered to micro particles and it caused to smoke reduction. The heat produced from water vapour reduce the temperature of internal combustion chamber and it caused to inhibition of NOx production. It can be verified by the lower exhaust temperature of each ND-13 mode using emulsion fuel than that of MDO fuel. The NOx and smoke concentration were reduced by increasing water content in emulsion fuel. The power also decreased according to the increment of water content of emulsion fuel because emulsion fuel has low calorific value due to high water content than MDO. As a result of ND-13 mode test with 17% moisture content, it was achieved 24% reduction in NOx production, 76% reduction in smoke density, 11% reduction of $SO_2$ and 13% reduction in power loss.

• Journal of the Korean Society of Safety
• /
• v.25 no.6
• /
• pp.92-97
• /
• 2010

A study is conducted on thermal characteristics of biodiesel which is already being produced in many countries because of its stable supply of energy in non oil-producing countries and economical benefits against increasing oil price, and environment conservation. So biodiesel has been used as important energy source in the fuel fields and a mount of production has increased year by year. Therefore, it is very important to find out the thermal characteristics of biodiesel for ignition temperature, maximum pressure and thermal behavior. The purpose of this study is to compare on thermal characteristics of biodiesel, petroleum diesel and those mixtures. Also, the main study was performed by flash point testers and modified closed type of pressure vessel test (MCPVT). Based on the data of flash point and MCPVT, the ignition temperature and the maximum pressure of biodiesel was $182^{\circ}C$ and 40.1bar, and petroleum diesel was $54^{\circ}C$ and 29.8bar.

• Environmental and Resource Economics Review
• /
• v.32 no.3
• /
• pp.167-190
• /
• 2023

This study analyzes the potential demand for automobiles based on fuel type using survey data in Korea. The dependent variable of the model is the future desired fuel type, including gasoline, diesel, hybrid, electricity, and hydrogen. The main explanatory variables are the respondent demographic characteristics, key reasons for choosing vehicle fuel type and environmental awareness extracted via principal component analysis (PCA). Using a multinomial logit (MNL) model, we find that respondents who consider fuel economy and infrastructure increase the demand for a hybrid car but decrease the demand for electric and hydrogen vehicles. The denial-types increase the demand for gasoline (petrol) and diesel (light oil), and decrease the demand for electric vehicles. The anxiety-types increase the demand of hybrid vehicles, and decrease the demand for electric vehicles. In contrast, in the case of pro-types, the demand for diesel (light oil) hydrogen vehicles decreased.

• The KSFM Journal of Fluid Machinery
• /
• v.20 no.2
• /
• pp.53-62
• /
• 2017

In this paper, the effect of oil conditions in rotor dynamic behaviors of a FFRB (Fully-Floating Ring Bearing) is investigated. Through the characteristic of a FFRB has two films, it has several advantages such as less friction loss and better stability over a wide speed range. However, it is difficult to supply a oil to the inner film. Thus, turbocharger makers have been paid significant attention to the lubrication of a FFRB because of its importance. This work focuses on the influence of oil inlet pressure and temperature. The methodologies of computational simulation and experimental test were used to estimate the rotor dynamic behaviors. In experimental test, the single-scroll turbocharger for the 1.4L diesel engine was used. The results show that the oil inlet pressure and temperature will place considerable influence on the rotor response. Oil conditions affect RSR (Ring Speed Ratio) which is cause of sub-synchronous vibrations, which also cause of oil whirling and whip even a critical speed. At higher speed range, the phenomenon of self-excited vibrations which is cause of instability of fluid whirl is investigated through the orbit shapes that consist of small orbit and large amplitude orbit. It is shown that some performance of a FFRB can be controlled by the conditions of oil supply. Finally, it was revealed that the oil induced operating conditions will strongly affect the turbocharger rotor dynamics behaviors.

• Journal of The Korean Society of Agricultural Engineers
• /
• v.49 no.6
• /
• pp.55-62
• /
• 2007

Actual states of energy utilizations were investigated and analyzed on three representative rural villages in Chungcheongnam-Do. Rural residents were almost using the ondol boiler as a heating facility and oil(diesel, kerosene) and electricity(night thermal-storage power service) as a heating energy. There were a few households using briquette or firewood in a fuel hole with Korean hypocaust. Most of their cooking facilities were gas ranges using LPG. The most popular hot-water supply system was an oil boiler and the next was an electricity boiler. The amount of energy use in a rural household generally showed 20,000 to 40,000 won/month of the electric power rate, 400 to 800 liter/year of the oil and 60 to 120 kg/year of the LPG. Prompt measures should be taken to promote the spread of new and renewable energy such as solar heat, biomass and wind power, etc.

• Journal of Advanced Marine Engineering and Technology
• /
• v.33 no.7
• /
• pp.1044-1051
• /
• 2009

During contact between surfaces, there is wear and the generation of wear. The particles contained in the lubricating oil carry detailed and important monitoring information about the condition of the machine. Therefore, this paper was undertaken for the Ferrography system of wear debris generated from a lubricated moving machine surface. The lubricating wear test was performed under different experimental conditions using the Falex wear test of the Pin and V-Block types by Ti(C,N) coated. It was shown from the test results that wear particle concentration(WPC), wear severity index(Is) and size distribution have come out all higher with increases in sliding friction time. With the Ferrogram thin leaf wear debris as well as ball and plate type wear particles were observed.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.5 no.4
• /
• pp.338-346
• /
• 1981

Honing, lapping, polishing and superfinishing are applied for a precision machining to finish the metal surface, but these precision machining are micro-cutting by hard and micro-abrasive grains. Frictional machining is the new method to finish mirrorlike surface without using those abrasive grains. The frictional machining produces high pressure and high temperature instantly by compressing a tool material against the metal surface in sliding motion. The metal surface is given plastic deformation and plastic flow by the above mentioned frictional motion, but the surface roughness of the metal surface is influenced by physical and chemical reaction in surrounding atmosphere. Therefore, the atmosphere around the metal optimum atmosphere in the frictional machining. The part 1 of the study was performed in liquid atmospheres. Diesel oil, lubricant, grease, lard oil, bean oil and cutting fluid were used as such atmospheres. Medium carbon steel SM 50 C was used as a workpiece and ceramic tip was applied as a frictional tool. The result of the experiment showed characteristic machining conditions to generate the best surface roughness in each atmospheres.

• Journal of the korean Society of Automotive Engineers
• /
• v.13 no.5
• /
• pp.81-88
• /
• 1991

Combustion characteristic, concentration of NOx and exhaust smoke opacity was experimentally tested, according to fuel injection timing, mixing ratio of water and methanol for the driving condition of 2000 rpm of engine revolution and constant load(7.5kg/cm$^{2}$) using emulsified fuel of gas oil-water methanol. The result obtained was as following. Thermal efficiency indicated highly 0.4-2.7% for emulsified fuel then gas oil, and injection timing when maximum thermal efficiency, slicily risen then gas oil. For constant fuel injection timing ignition lag was increased, combustion duration decreased, maximum heat release rate indicated high, and concentration of NOx and exhaust smoke opacity is decreased, as function of water and methanol content y was higher.