• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 2009.10a
• /
• pp.371-374
• /
• 2009

Die casting process has been used widely for complex automotive products such as the knuckle, arm and etc. Generally, a part fabricated by casting has limited strength due to manufacturing defects by origin such as the dendrite structure and segregation. As an attempt to offer a solution to these problems, forging has been used as an alternative process. However, the forging process provides limited formability for complex shape products. Rheo-forging of metal offers not only superior mechanical strength but also requires significantly lower machine loads than solid forming processes. This paper presents the results of an A356 aluminum alloy sample, which were obtained by experiment and by simulation using DEFORM 3D. Samples of metal parts were subsequently fabricated by using hydraulic press machinery.

• Journal of the Korean Society for Precision Engineering
• /
• v.20 no.2
• /
• pp.58-65
• /
• 2003

The conventional forming process such as squeeze casting or die casting for fabricating metal matrix composites products have a disadvantage such as non homogenous distribution of reinforcement, weak bonding between matrix and reinforcement and cost increase in parts fabrication. Thixoforming process has been accepted as a new method for fabricating the net shaped metal matrix composites with lightweight and wear resistance. In this paper, the effect of volume fraction and reinforcement sizes on mechanical properties in cylinder liner part of metal matrix composites has been investigated with processes parameters such as pressure and velocity. Moreover, the methods to obtain the thixoforged composites cylinder liner with high quality has been proposed. To evaluate the composites cylinder linear fabricated at the conditions proposed in this study, mechanical properties of fabricated composites cylinder linear were compared with those of commercial composites cylinder linear.

• Transactions of Materials Processing
• /
• v.16 no.3 s.93
• /
• pp.178-186
• /
• 2007

Rheo-forging process of aluminum alloy is suitable for large parts of net shape without defects and excellent mechanical properties in comparison with conventional die casting and forging process. To control the microstructure of the product with high mechanical properties in rheo-forming, solid fraction is required to prevent porosity and liquid segregation. Therefore, in rheo-forging process, die shape, pressure type and solid fraction are very important parameters. The defects such as porosity, liquid segregation and unfitting phenomena occur during rheo-forging process. To prevent these defects, mechanical properties and microstructure analysis of samples versus the change of pressure are carried out and the problem and its solutions are proposed. Also, the mechanical properties versus various pressures were compared with and without heat treatment. The alloys used for rheo-forming are A356 and 2024 aluminum alloy. The rheology material is fabricated by electromagnetic process with controlling current and stirring time.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2001.04a
• /
• pp.45-48
• /
• 2001

SL(Stereolithogrphy) part is made by piling up thin layers which causes the stair stepping effect at the surface of SL parts. This effect causes excessive surface roughness and requires additional postprocess finishing such as abrasive basting which is detrimental to part geometry and time consuming. Hence paraffin coating and grinding postprocess is proposed to raise the surface quality of SL part. The paraffin which has suitable properties for the proposed postprocess is coated all over the part surface. By grinding the thin layer of coated on the SL part only, the surface roughness can be improved without any damage on the part. From the experimental result, It is verified as very practical for die casting with silicon rubber mold.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.41 no.5
• /
• pp.337-343
• /
• 2017

As a shop practice, a strength estimation method for die cast parts is suggested, in which various defects such as pores can be allowed. The equivalent porosity is evaluated by combining the stiffness data from a simple elastic test at the part level during the shop practice and the theoretical stiffness data, which are defect free. A porosity equation is derived from Eshelby's inclusion theory. Then, using the Mori-Tanaka method, the porosity value is used to draw a stress-strain curve for the porous material. In this paper, the Hollomon equation is used to capture the strain hardening effect. This stress-strain curve can be used to estimate the strength of a die cast part with porous defects. An elastoplastic theoretical solution is derived for the three-point bending of a die cast beam by using the plastic hinge method as a reference solution for a part with porous defects.

• Journal of Korea Foundry Society
• /
• v.21 no.3
• /
• pp.163-178
• /
• 2001

The squeeze infiltration process is potentially of considerable industrial importance. The performance enhancements resulting from incorporation of short alumina fiber into aluminum are well documented. These are particularly significant for certain automobile components. Aluminum matrix composite automotive parts, such as diesel engine pistons or engine blocks are produced using squeeze casting apparatus or pressure die-casting apparatus. But the solidification process gets complicated with manufacturing parameters and the factors for porosity formation have not fully understood yet. In this study the formation of porosity during squeeze infiltration has been studied experimentally to achieve an improved understanding of the squeeze infiltration process for manufacture of short-fiber-reinforced components, particularly the mechanism of porosity formation. Al-based MMCs produced under a range of conditions were examined metallographically and the porosity characterised;a kind of matrix, an initial temperature of melt, and a volume fraction of reinforcement. The densimetry and the microscopic image analysis were done to measure the amount of porosity. A correlation between manufacturing parameters and defects was investigated through these.

• Journal of Korea Foundry Society
• /
• v.32 no.1
• /
• pp.44-49
• /
• 2012

In this study, three magnesium alloys were investigated; those are 1.5wt.% CaO added AM80, 1.0wt.% CaO added AM60, and conventional MRI153 alloys. Test specimens of three alloys were prepared by re-melting and casting into steel mold with ingots and machining. The mechanical properties and the creep behavior at 150 degrees Celsius of these specimens were determined and their microstructures were characterized using OM and SEM. For the application to die-casting, fluidity test were carried out with spiral mold. Compared with 1.0wt.% CaO added AM60 alloy, 1.5wt.% CaO added AM80 alloy exhibited good creep properties in all test conditions. Moreover, CaO added alloys showed better creep properties than MRI153 alloy at lower load condition. It is proposed that 1.5wt.% CaO added AM80 alloy is useful to apply to power-train parts such as transmission case in vehicles.

• Design & Manufacturing
• /
• v.16 no.3
• /
• pp.16-21
• /
• 2022

In order to reduce the weight of parts and materials for the development of high-efficiency engines in accordance with the strengthening of automobile fuel efficiency regulations, the existing casting material is changed to a iron plate material, and plastic processing and turning operations are performed to lighten the weight and reduce the manufacturing cost. Among the pulley components applied to the damper pulley, the HUB product was manufactured by plastic machining instead of the existing casting process, and the inspection standardized for automating the inner diameter and parallelism measurement of the turning result of the new hub part with improved quality, and the inspection system for this Development of design and operation software to automate the inspection of the inner diameter and parallelism of the hub was described. The representative specifications of the development equipment are a hub inner diameter 22mm inspection system, a three-point inspection system with a parallelism of 0.15mm on the top.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2002.05a
• /
• pp.882-885
• /
• 2002

Magnesium alloys are very attractive materials for appling to the development of autemobile parts or electric goods where light weight and higher stiffness. Due to higher ratio of strength vs. weight and stillness vs. weight, various magnesium alloys are well applied in much weight saving design applications though extrusion or die-casting process. However for the requisites of higher strength and weight savings, some new fabrication processes has been and it can be realized though the aid of injection modeling technology. To obtain the parametric data base for the injection molding process, various experiments were executed for AZ91D magnesium alloy. This paper propose the optimum condition of injection temperature, first and second pressure. the process was lined-up successfully often changing the injection unit. fluid pressure system from the conventional plastic injection molding process.

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.11 no.4
• /
• pp.173-179
• /
• 2012

In recent years, Magnesium(Mg) and its alloys have become a center of special interest in the automotive industry. Due to their high specific mechanical properties, they offer a significant weight saving potential in modern vehicle constructions. Most Mg alloys show very good machinability and processability, and even the most complicated die casting parts can be easily produced. In this study, Microstructure, Vickers hardness and tensile tests were examined and performed for each specimen to verify effects of forming conditions. Also to verify upsettability and forming limit of the specimen at room temperature and elevated temperature, upsetting experiments were performed. For comparison, experiments at elevated temperature were performed for various Mg alloy, such as AZ31, AZ91, and AM50. The experimental results were compared with those of CAE analysis to propose forming limit of Magnesium alloys.