• 대한기계학회논문집A
• /
• 제40권2호
• /
• pp.221-227
• /
• 2016

풍력발전기에서 메인 샤프트는 로터허브와 증속기를 연결하는 중요 부품 중 하나이며 주로 자유단조공법을 통하여 제조된다. 하지만 고 MW급 이상의 메인샤프트는 중량을 감소시키기 위하여 중공형 설계가 이루어지며 주조공법을 이용하여 제조되고 있다. 본 연구의 목적은 중공형 메인샤프트를 단조공법을 이용하여 생산할 수 있는 제조공정을 개발하는 것이다. 자유단조 공법의 공정설계 방법에 따라 중실형과 중공형 메인샤프트를 제조하기 위한 단조공정을 각각 설계하였다. 설계된 공정의 성형가능성을 확인하기 위하여 온도, 변형률 속도에 따른 유동응력을 열간압축실험을 통하여 구한 후 유한요소해석을 수행하였다. 유한요소해석을 통하여 단조업계에서 통상 행해지는 중실형 단조공법의 온도 및 변형률 등의 관리인자와 제안된 중공형단조공법의 인자를 비교하여 성형가능성을 예측하였다. 시제품 제작을 통하여 중공형 형상을 원소재회수율, 내부품질, 형상 및 치수 등에서 높은 생산성으로 제조가 가능함을 확인하였다.

• 소성∙가공
• /
• 제20권3호
• /
• pp.214-221
• /
• 2011

In recent years, automotive seat components have been manufactured by the fine blanking process, allowing an improvement of dimensional accuracy at sheared surface in series production. However, the rollover has increased and die failures have occurred more frequently when manufacturing gears by fine blanking. Consequently, important goals for manufacturing seat recliner parts with gears have been to decrease the rollover as well as to improve the tool life. In this study, the half blanking and shaving processes were introduced to improve aforementioned problems for the lower tooth, the main component of a seat recliner. For this purpose, the half blanking process was optimized using the finite element (FE) analysis and design of experiment (DOE). The optimized conditions resulting from this study were an offset of 0.2 mm, a clearance of 0.1 mm and a penetration depth of 4.5 mm. Fine blanking experiment conducted under the optimal condition resulted in a rollover depth decrease from 1.9 to 1.3 mm, and no die failure occurrence.

• 한국자동차공학회논문집
• /
• 제24권3호
• /
• pp.338-344
• /
• 2016

The study is actively being performed to increase fuel injection pressure of common rail system among countermeasures to meet the emission regulation strengthen of the Diesel engine. The common rail fuel injection tube in such ultra high pressure common rail system has the weakest structural characteristics against vibration that is generated by fuel injection pressure and pulsation during engine operation and driving. Thus the extreme durability is required for common rail fuel injection tube, and the drawing process is being magnified as the most important technical fact for strength of seamless pipe that is the raw material of common rail tube. In this respect, we analyzed the characteristic of dimension and stress variation of the ultra high pressure common rail fuel injection tube by variation of Die and Plug angle in drawing process. Based on the analysis, we tried to obtain the raw material strength of common rail fuel injection tube for applying to the ultra high pressure common rail system. As a result, Plug angle is more important than entry angle of Die and we could obtain the target dimension and strength of the ultra high pressure common rail fuel injection tube through optimization of Plug angle.

• 대한기계학회논문집
• /
• 제11권3호
• /
• pp.509-518
• /
• 1987

본 연구에서는 냉간 축대칭 전방 압출에 가중잔류항법을 적용하여 재료의 가 공 경화 및 강소성 경계를 고려하는 프로그램을 개발하여 변형도, 응력, 변형력, 강소 성 경계등을 FEM과 동일한 조건에서 비교 해석하고 다른 공정에 적용할 수 있게 하고 또한 곡면다이와 원추형다이를 설계 제작하여 다이의 형상과 단면 감소율이 변형도와 응력 분포에 미치는 영향을 검토하고 압출된 제품의 성질을 분석하여 실제 공정에 이 바지하며 이론 계산과 실험을 비교함이 목적이다.

• 소성∙가공
• /
• 제18권8호
• /
• pp.640-645
• /
• 2009

Recently, boss and rib test based on backward extrusion process was proposed to quantitatively evaluate the interfacial friction condition in bulk forming process. In this test, the tube-shaped punch with hole pressurizes the workpiece so that the boss and rib are formed along the hole and outer surface of the punch. It was experimentally and numerically revealed that the height of boss is higher than that of the rib under the severe friction condition. This work is focused on the effect of the punch design and flow stress on deformation pattern in boss and rib test. From the boss and rib test simulations, it was found that there is slight variation in both the heights of boss and rib according to the length of punch land, nose radius, and face angle. However the hole diameter of the punch and the clearance between the punch and die have a significant influence on the calibration curves showing the heights of the boss and rib. In addition, the effect of flow stress on the calibration curves was investigated through FE simulations. It was found that there is no effect of strength coefficient of the workpiece on the calibration curves for estimation of friction condition. On the other hand, the strain-hardening exponent of the workpiece has a significant influence on the calibration curve.

• 전기학회논문지
• /
• 제57권10호
• /
• pp.1752-1758
• /
• 2008

This paper deals with the reduction of friction torque in permanent magnet motors by using the heat treatment of stator core. The stator core is made of electrical steel sheared by the punching die. From the punching process, large mechanical stress acting on the edge of stator tooth induces significant plastic and elastic deformation and then cause the change of magnetization properties. Then, the mechanical and magnetic unbalance in the sheared region of stator tooth produced by material cutting has influence on the friction torque. This paper investigated the effect of the punching process on the magnetization process and the mechanical deformation, and then proposed the stress relief annealing method for the reduction of friction torque among one of motor characteristics.

• 한국추진공학회:학술대회논문집
• /
• 한국추진공학회 1998년도 제11회 학술강연회논문집
• /
• pp.16-16
• /
• 1998

우주발사체용 로켓트 구조재로 사용되는 알루미늄합금 단조재는 강도확보를 위하여 고온으로 가열후 급냉과정에서 상당한 크기의 잔류응력이 발생되고 이로 인해 기계가공시 변형이 유발되어 조립성이 나빠진다. 잔류응력은 그 크기가 재료의 항복강도를 초과할 때 제거되므로 응력제거(stress relief)를 위해서는 외부하중이 가해져야 한다. 응력제거 처리는 소성변형, 열처리 및 초음파 등의 방법으로 수행되며 소성변형에 의한 제거효과가 가장 크다 형상이 복잡한 형 단조재의 경우 열간단조금형과 동일한 금형을 이용하는 TX52 등의 방법을 적용한다고 알려져 있으나 TX54에 대한 금형설계 및 소성변형률 적용 데이터는 공정 know-how로 분류되어 있다. 잔류응력제거 처리의 해석적 연구로는 판재와 링롤재에 대해서는 인장 및 압축 소성변형에 적용에 대한 결과가 발표된 바 있으나 형 단조재의 경우에는 전무하다

• 소성∙가공
• /
• 제21권5호
• /
• pp.291-297
• /
• 2012

In this paper, the effect of back tension in multi-pass drawing or wiredrawing on the central bursting defect is investigated using finite element predictions. A rigid-plastic finite element method was used together with the McClintock damage model. Central bursting defects under different back tension stress values ranging from 0% to 20% of the yield strength of the material were predicted and they were compared to understand the effect of the back tension stress values on the central bursting defect. It is found that the level of back tension has a strong influence on the cumulative damage. Thus, higher back tension raises the possibility of the central bursting defect occurring, even though it decreases the interfacial pressure between the die and the work piece.

• 소성∙가공
• /
• 제13권6호
• /
• pp.490-496
• /
• 2004

Springback comes from the release of external loads after forming. The control of phenomenon is especially important in the sheet metal forming since there are no other practical methods available to correct the dimensional inaccuracy from springback. Therefore the accurate prediction before the die machining has been a long goal in the field of sheet metal forming. The am of the present study is to enhance the prediction capability of finite element (FE) analysis for the springback phenomenon. For this purpose FE analysis for V-bending has been carried out with the commercial programs, LS-DYNA. The FE analysis results have been validated through the comparison of experimental. The experimental results measured directly by the strain gauge have given the confidence to FEA.

• 한국안전학회지
• /
• 제26권4호
• /
• pp.1-6
• /
• 2011

New methods for joining sheet of metal are being sought. One of the most promising methods is MPJ (mechanical press joining). It has been used in thin metal work because of its simple process and relative advantages over other methods, as it requires no fasteners such as bolts or rivets, consumes less energy than welding, and produces less ecological problems than adhesive methods. In this study, the joining process and static behavior of single overlap joints has been investigated. During fixed die type joining process for SPCC plates, the optimal applied punching force was found. The maximum tensile-shear strength of the specimen produced at the optimal punching force was 1.75 kN. The FEM analysis result on the tensile-shear specimen showed the maximum von-Mises stress of 373 MPa under the applied load of 1.7 kN, which is very close to the maximum tensile strength of the SPCC sheet(= 382 MPa). This suggests that the FEM analysis is capable of predicting the maximum tensile load of the joint.