• Journal of Sensor Science and Technology
• /
• v.24 no.3
• /
• pp.208-213
• /
• 2015

The purpose of this study is to optimize the design of a capacitive pressure sensor element using the simulation of electrical characteristics. The simulation of the ceramic sensor diaphragm ($Al_2O_3$) was performed by permitting pressure to change the curvature of the diaphragm. The pressure capacitance ($C_P$) was increased from 19.63 pF to 15.26 pF by applying pressure because the distance between the electrodes has been changed from $30{\mu}m$ to $15{\mu}m$. When the thickness of the diaphragm was changed to 0.46~0.52 mm, a larger capacitance change showed in accordance with the reduced thickness, which means an increase of sensitivity. However, considering the viewpoint of the signal linearity, it was selected for the optimum thickness of the diaphragm to 0.50 mm. The designed sensor element based on simulated results was tested to measure the output characteristics. Comparing of simulated and measured results, there was a margin of error of approximately 2%.

• Journal of the Korean Magnetics Society
• /
• v.20 no.6
• /
• pp.234-238
• /
• 2010

Solenoid diaphragm fuel pump, which to replace mechanical fuel pump system by utilizing cam-shaft driving force, is in the spotlight for being a high efficient green car component. However, there is a drawback in power consumption as a solenoid diaphragm fuel pump only relies on solenoid for its flux needed in reciprocating motion. Therefore, this research proposes permanent magnet type VCM (Voice Coil Motor) fuel pump system to minimized power consumption. Furthermore, the study compares and analyzes power consumption and dynamic performance between the current and the former solenoid diaphragm pump by conducting finite element analysis with the commercial electromagnetic solver, MAXWELL.

• Journal of the Computational Structural Engineering Institute of Korea
• /
• v.16 no.1
• /
• pp.19-32
• /
• 2003

The structural system of a hybrid building is composed of upper shear wall which resist lateral force by bending deformation and lower frame which resist lateral force by shear deformation. A deep transfer girder is used to transfer gravity load safely from super structures to structural frame beneath. Because of the vertical discontinuity, a building with transfer girder must be analyzed by dynamic analysis. However, this structural system has many problems in performing dynamic analysis that cannot be solved by general analysis procedure. The slabs In transfer floor are considered as either a Plate element or a rigid diaphragm in finite element analysis without appropriate evaluation of their characteristics. Therefore, a reasonable analysis method is proposed in this study by evaluating the diaphragm effect of a hybrid structure system.

• Steel and Composite Structures
• /
• v.6 no.4
• /
• pp.303-317
• /
• 2006

The connection with combined cross diaphragm is developed for the connection of square CFT column and steel beam and proposed to be used for the frame with asymmetric span length. The structural characteristics of this connection lie in the penetration of the beam flange in the direction of major axis through the column for the smooth flow of stress. The purpose of this study is to analyze the dynamic behavior and stress flow of suggested connection and to evaluate the resistance to shock of connection. Four T-type CFT column-to-beam specimens; two with combined cross diaphragm and the others with interior and through diaphragms, the existing connection types, were made for cyclic load test guided by the load program of ANSI/AISC SSPEC 2002. The results show that the proposed connection is more efficient than existing ones in terms of strength, stress flow and energy absorption and satisfies the seismic performance required in the region of weak/moderate earthquakes.

• Journal of the Korean Geotechnical Society
• /
• v.16 no.5
• /
• pp.179-191
• /
• 2000

본 연구에서는 화강토 지반상의 자립식 diaphragm wall의 거동을 연구하기 위하여 벽체의 근입깊이비, 지하수위 및 굴착조건(연속 및 단계굴착)을 변화시키면서 원심모형시럼을 수행하였다. 원심모형실험시 지반굴착은 흙과 동일한 밀도로 혼합된 zine chloride 용액이 배수되도록 밸브를 조작하여 실시하였으며, 굴착에 의해 발생되는 지반의 변형괴 벽체의 변위 및 휨모멘트를 시간경과에 따라 측정하였다. 실험결과, 벽체의 근입깊이비가 증가함에 따라 벽체의 휨모멘트는 증가하는 반면, 굴착과정동안 배면측에서의 간극수압 감소속도는 감소하였다. 최종 굴착단계에서 굴착후 시간경과에 따른 침하량은 굴착과정중의 침하？에 비해 5~7% 정도를 나타내었다. 최대표면침하량과 벽체변위를 굴착깊이로 정규화한 결과 최대 침하량은 벽체 변위량의 0.8~1.2배9평균0.91배)사이에 분포하였다. 굴착깊이로 전규화한 벽체변위와 근입깊이와의 관계는 지수함수식으로 제안하였다. 파괴면은 직선적인 형태로 파괴면내의 배면측 지반은 벽체를 향하여 하향의 변위를 일으키면서 벽체의 회전에 의해 파괴되었으며, 퐈괴면의 각도는 66~72.5$^{\circ}$정도로 이론적인 파괴면의 각도보다 크게 평가되었다.

• Journal of Sensor Science and Technology
• /
• v.28 no.3
• /
• pp.177-181
• /
• 2019

Pressure sensors are used in various industries such as automobiles, airplanes, medical equipment, and coolers. Even if the ambient temperature changes, the measurement is reliable and stable. In this study a diaphragm-type pressure sensor was used to derive a temperature-compensated pressure estimation equation for accurate pressure measurement at $100^{\circ}C$ and $-40^{\circ}C$. To understand the characteristics of the pressure sensor diaphragm with respect to temperature and pressure, experiments were conducted in temperature-variable chamber using FEM analysis to confirm that the influence of temperature effect was nonlinear. Based on the experimental results, a nonlinear method for calculating the pressure by compensating for the error due to temperature was derived. The calculated pressure value is lower than 0.5 % at low and high temperatures, and lower than 0.4 % at $22^{\circ}C$, thereby eliminating the effect of temperature.

• Journal of Korea Multimedia Society
• /
• v.22 no.2
• /
• pp.271-280
• /
• 2019

Recently, hearing loss patients have been increasing to excessive use of various multimedia devices. One of the hearing rehabilitation systems, bone conduction hearing aid can be used to conductive deafness patients efficiently. However, the conventional bone conduction hearing systems has some problems such as skin diseases, repulsion of patients, and vibration power reduction by skin damping. In this paper, to overcome the conventional problems, we proposed power improvement method by curved beam diaphragm. The proposed method is skin attachment system which is non-implantable, and then the power of transducer is improved by the proposed method. In order to improve the vibration power of diaphragm, variable that has correlation with displacement are extracted, the diaphragm designed by extracted variable. To verify efficient of the proposed method, experiment conducted by finite element analysis. As a result of, the proposed method confirmed improved power to compare with the conventional method and proposed method.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.25 no.6
• /
• pp.20-28
• /
• 2021

High enthalpy test facilities, such as a shock tunnel, are to be operated at the specific pressure ratio according to the desired test condition. A metallic diaphragm is machined or a forced rupture device is used to open it at a specific pressure ratio. The diaphragm opening procedure takes several hundred microseconds including rupture and deformation. This process is expected to affect the test conditions. In this study, numerical simulation was performed for different materials, thicknesses, and opening ratios. And the characteristics of shock wave generation and the stagnation condition in the tube are investigated. Results show that the final opening ratio and rupturing procedure directly affect the speed of a shock wave, stagnation pressure, and test time.

• Physical Therapy Rehabilitation Science
• /
• v.12 no.3
• /
• pp.278-292
• /
• 2023

Objective: This study was performed to investigate the effects of thoracic joint mobilization and breathing exercises on diaphragmatic thickness, chest expansion, respiratory function, and endurance in patients with chronic stroke. Design: Randomized controlled trial Methods: The study included 24 chronic stroke patients who were randomly divided into two groups. The experimental group (12 people) performed 15 minutes of thoracic joint mobility exercises and 15 minutes of breathing exercises, three times a week for 6 weeks, 30 minutes each time. The control group (12 people) received 15 minutes of conservative physical therapy and 15 minutes of breathing exercises, 3 times a week for 6 weeks, 30 minutes per session, the same as the experimental group. The experimental and control groups performed the same breathing exercises. To assess training effectiveness, changes in diaphragm thickness, chest expansion, respiratory function, and endurance were measured. Results: As a result, the experimental group exhibited significant improvements in diaphragm thickness, chest expansion, and respiratory function. The endurance mode also displayed significant enhancement (p<0.05), a finding consistent with the control group. However, the experimental group displayed more substantial improvements in non-affected diaphragm thickness and thoracic expansion compared to the control group (p<0.05). Conclusions: Drawing from these findings, breathing exercise which combine thoracic mobilization, will be actively utilized in addition to physical therapy interventions in clinical trials as an effective intervention method.

• The Journal of the Acoustical Society of Korea
• /
• v.25 no.5
• /
• pp.222-228
• /
• 2006

The acoustical property of micro-speaker had been investigated as a function of the diaphragm material in this study. Young's modulus and the density of material is deeply related to the determination of sound velocity and stiffness. As a result, it was appeared that the resonance frequency of micro-speaker was PEI < PPS < PET < PEN. This experimental result was in an excellent agreement with the theoretical one. The increasing ratio of sound pressure level to the frequency between 20Hz and the resonance frequency ($f_s$) and the high resonance frequency ($f_h$) were not affected by the diaphragm material.