• Proceedings of the Korea Concrete Institute Conference
• /
• 2003.05a
• /
• pp.961-966
• /
• 2003

In recent, the design of diaphragm which is representative disturbed region in PSC box girder bridge have been performed according to the empirical method or beam theory. But, these methods couldn't be described the behavior of the end diaphragm, and placed reinforcements accurately. As the compressive stress transferred by the web concentrated on the lower parts of diaphragm, it was demonstrated that the basic assumption of 2-D strut-and-tie model for the diaphragm that the compressive stress acts on the upper parts of the diaphragm is wrong. Meanwhile, in this research, after analyzing the variables of end diaphragm, the 2-D strut-and-tie models appropriate to each cases are proposed. And, the problems of 2-D strut-and-tie model were analyzed, so 3-D strut-and-tie model is proposed as well. There is no codes which include the demonstration of safety of 3-D strut-and-tie model. Hence, for nodes, the stresses at the elements which included the singular node in strut-and-tie model were investigated using the finite element analysis. And, the stress states of strut has one direction, so effective stresses were considered at the stage, dimensioning of the model. From the results, 3-D strut-and-tie model could predict the behavior of end diaphragm accurately, and design of reinforcement could be performed economically.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2006.05a
• /
• pp.844-849
• /
• 2006

Accurate modeling of complex dynamic stiffness of the pneumatic springs is crucial for an efficient design of vibration isolation tables for precision instruments such as optical devices or nano-technology equipments. Besides pressurized air itself, diaphragm made of rubber materials, essentially employed for prevention of air leakage, plays a significant contribution to the total complex stiffness. Therefore, effects of the diaphragm should be taken care of precisely. The complex stiffness of an inflated diaphragm is difficult to predict or measure, since it is always working together with the pressurized air. In our earlier research, the complex stiffness of a diaphragm was indirectly estimated simply by subtracting stiffness of the pressurized air from measurement of the total complex stiffness for a single chamber pneumatic spring. In order to reflect dynamic stiffness of inflated diaphragm on the total stiffness at the initial design or design improvement stage, however, it is required to be able to predict beforehand. In this presentation, how to predict the complex stiffness of inflated rubber diaphragm by commercial FE codes(e.g. ABAQUS) will be discussed and the results will be compared with the indirectly measured values.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.20 no.2
• /
• pp.67-75
• /
• 2019

The diaphragm used for CFT columns has a small amount of steel to be used, but has a disadvantage that welding is difficult and openings are required because the steel tube and four sides must be welded. The improved diaphragm to be examined in this study was cut into four corners by cutting the center hole for concrete filling. In the improved diaphragm, the width of the center hole is the same as that of the previous diaphragm, but the width of the diaphragm contacting the steel tube is reduced, thereby reducing the welding length by about 70% compared to the previous diaphragm. The in-plane strain of each specimen was analyzed when the same load was applied to the interior diaphragm through a simple tensile test. Using the general FEM program(ANSYS 19.2), the analysis was performed under the same conditions as the actual simple tensile test, and the load transfer between the improved diaphragm and the previous diaphragm was compared. When the width of the diaphragm is equal to or smaller than the flange width, stress is concentrated from the end of the diaphragm, and when the flange width is larger, stress is concentrated at the center.

• JSTS:Journal of Semiconductor Technology and Science
• /
• v.5 no.1
• /
• pp.52-57
• /
• 2005

This paper describes a fabrication method of a circular diaphragm using boron etching stop method. It will be applied to acoustic transducers such as microphones or microspeakers and so on. The sensitivity is expected to be increased with the circular diaphragm through the simulation results to compare with a general rectangular diaphragm. The borondoped layer which is doped with solid source is sufficient for achieving an etching stop in 20 wt% TMAH, and the thickness is about $7.4{\mu}m$. The diameter of the circular silicon nitride diaphragm was measured to be 2 mm with $1{\mu}m$ thickness. The fabrication of piezoelectric acoustic devices was completed.

• Journal of Sensor Science and Technology
• /
• v.5 no.2
• /
• pp.1-8
• /
• 1996

In this paper, We have designed silicon pressure sensor with center-bossed diaphragm which improving sensitivity and linearity by reducing diaphragm deflection. Designed center-bossed pressure sensor showed maximum deflection of $0.125{\mu}m$, maximum stress of $2.24{\times}10^7 Pa$ and sensitivity of 27.67 mV/V.psii. As a result, diaphragm deflection was reduced to 1/160 that of diaphragm thickness and 1/35 that of square diaphragm. Also, sensitivity was increased 19 times compared to square diaphragm.

• New & Renewable Energy
• /
• v.7 no.3
• /
• pp.29-35
• /
• 2011

This paper describes an internal flow characteristics of a fuel pressurized blower, used for 1kW domestic fuel cell system. To analyze the flow field inside the diaphragm cavity, compressible unsteady numerical simulation is introduced. SST model with scalable wall function is employed to estimate the eddy viscosity. Moving mesh system is applied to the numerical analysis for describing the volume change of a diaphragm cavity in time. Throughout numerical simulation with the modeling of the inlet and outlet valves in a diaphragm cavity, unsteady nature of an internal flow is successfully analyzed. Force variations on the lower plate of a diaphragm cavity are evaluated in time. It is found that the driving force at the suction stage of a diaphragm cavity is more necessary than that at the discharging stage.

• Annals of Clinical Neurophysiology
• /
• v.20 no.2
• /
• pp.93-96
• /
• 2018

Evaluation of diaphragm function is challenging because no single test has a high diagnostic yield. We describe ultrasound findings in three cases with acquired unilateral diaphragmatic elevation. These cases confirm that sonographic evaluation is a valid tool for identifying diaphragm dysfunction. In addition, ultrasound measurements of diaphragm thickness and the contractility can be used to determine if a diaphragm is paralyzed and suggest the duration of paralysis (i.e., acute or chronic).

• Proceedings of the Korea Concrete Institute Conference
• /
• 2000.10a
• /
• pp.297-302
• /
• 2000

This paper presents the effect of diaphragm spacing ratio(depth to span) on behavior and capacity of composite steel-concrete structures of sandwich system. Numerical analysis has been performed variety diaphragm ratio, behavior and load condition. As a results of this study, in case of shear behavior and concentrated load, the capacity of structure such as yielding and ultimate load improve according to diaphragm ratio because of concrete confining effect by steel plate and stress redistribution by diaphragm. But in case of bending behavior or uniform load, it proved that diaphragm ratio don't influence on behavior and capacity of composite structures of sandwich system.

• 한국전산유체공학회:학술대회논문집
• /
• 2010.05a
• /
• pp.86-92
• /
• 2010

A metal diaphragm compressor has been widely used for supplying a high pressures gas. This compressor mainly consists of gas oil space and metal diaphragm. Gas sucked in the gas space is compressed by an oscillating metal diaphragm existed between the gas and oil space. A non-return discharge and suction check-valve are components of the compressor that draw off the compressed oil and gas. Those components are self-actuated by differential pressures. Therefore, the rapid response and stable operating conditions are required. In the present study, to find out the dynamic behavior of the suction, discharge valve and diaphragm compressor, the unsteady flow field has been investigated numerically by using the unsteady two-way FSI (Fluid Structure Interaction) simulation method, $k-{\omega}$ turbulent model and mesh deformation.

• Proceedings of the Korean Reliability Society Conference
• /
• 2000.04a
• /
• pp.73-79
• /
• 2000

본 논문은 BCPS(Balanced canister purge solenoid valve) 의 Lab. 내구 시험 Spec. 결정 방법에 관한 것이다. BCPS 는 기존에 사용 중인 CPS(Canister purge solenoid valve) 의 응답성과 제어의 용이성을 좋게 하여 배기 가스 특성을 향상시키기 위해 CPS 내부에 Rubber 재질의 막(Diaphragm) 을 적용한 것이다. 하지만 이 Diaphragm 이 마모 등에 의해서 찢어지면, 오히려 배기 특성이 저하된다. 따라서 BCPS의 적용을 위해서는 이 Diaphragm 의 내구성이 검증되어야 하며, 이를 위해서는 새로운 신뢰성 시험 Spec. 의 개발이 필요하다. 본 연구에서는 BCPS Diaphragm의 검증을 위해 필요한 신뢰성 시험 Spec. 을 결정하였다. 이를 위해, X-ray Inspection System등을 이용하여 부압에 따른 Diaphragm 의 형상 변화 등을 관찰하였으며, 실제 차량에서 Diaphragm 에 걸리는 압력의 분포를 측정하였다.