• 설비공학논문집
• /
• 제11권4호
• /
• pp.448-456
• /
• 1999

Variations of thickness and effective thermal conductivity of frost forming on the horizontal] cylinder with respect to time were measured under cross flow. The local heat flux around the cylinder was determined by measuring the radial temperature distribution in the cylinder having small holes drilled axially in which T-type thermocouples were inserted, then by using one dimensional cylindrical heat conduction equation. The thickness and the surface temperature of the frost layer around the cylinder were measured periodically while developing the frost. Each experiment was peformed by varying the Reynolds number, the temperature, and the humidity condition. Specially the dew point temperature of the most cases was below the freezing point. Experimental data showed that the frost layers on the front and the rear surface were thicker than those on the top and the bottom one which was near the separation point. The thickness and effective thermal conductivity of the frost layer were affected by inlet air velocity, temperature, and humidity. Moreover, the effective thermal conductivity and the effective thermal resistance increase with respect to time.

• 설비공학논문집
• /
• 제1권2호
• /
• pp.116-127
• /
• 1989

Research on reheating cooling cycle and its practical application have been made to prevent unequalized distribution of temperature and humidity of room due to lack of supply air volume and dewdrops on supply diffusers to be taken place as a result of lower temperature of supply air than that of dew point of room air in cooling cycle of constant air volume, single duct, single zone and draw-through fan type. In view of the fact that human body is insensitive to humidity, it is possible not only to construct the complete non-reheating cooling cycle by increasing the humidity point allowable with the deduction of occupant's sense of pleasantness minimizing, but also to get cooling cycle decreasing the reheating quantity if the humidity exceeds the point allowable. In addition, it is possible to save maximum 8% in electric energy for cooling in cooling system by constructing non-reheating cooling cycle instead of reheating cooling cycle and by increasing the relative humidity of room from 50% to 65% in case efficiency and air pressure of cooling system are low. It is also possible to get an optimum cooling cycle by determining the room humidity in consideration of pleasantness of occupants and conservation rate of electric energy if the cooling capacity, efficiency and total pressure of cooling equipment are fixed.

• 청정기술
• /
• 제17권1호
• /
• pp.19-24
• /
• 2011

본 연구에서는 가변부피 투시창이 설치되어 있는 고압 상평형 측정 장치를 사용하여 이산화탄소의 임계온도 이상과 디메틸포름아마이드(DMF)의 임계온도 이하의 온도 범위에서 혼합물의 조성을 변화시키면서 이산화탄소와 디메틸포름아마이드 혼합물의 기포점 압력을 측정하였다. 실험적으로 측정된 기포점 압력 데이터를 Peng-Robinson 상태방정식에 상관시킴으로써 기포점 조성과 평형을 이루는 이슬점 조성을 추정하였다. 실험적으로 측정된 기포점 압력은 Peng-Robinson 상태방정식으로 계산한 결과와 매우 잘 일치하였다. 가변부피 투시창이 설치되어 있는 고압 상평형 실험장치는 고압의 압축유체 혼합물의 기포점을 매우 쉽고 빠르게 측정할 수 있는 방법이라고 할 수 있다.

• 공업화학
• /
• 제20권1호
• /
• pp.94-98
• /
• 2009

본 연구에서는 가변부피 투시창이 설치되어 있는 고압 상평형 측정 장치를 사용하여 이산화탄소의 임계온도 이상과 디메틸카보네이트의 임계온도 이하의 온도 범위에서 혼합물의 조성을 변화시키면서 디메틸카보네이트와 이산화탄소 혼합물의 기포점을 압력을 측정하였다. 실험적으로 측정된 기포점 압력 데이터를 Peng-Robinson 상태방정식에 상관시킴으로써 기포점 조성과 평형을 이루는 이슬점 조성을 추정하였다. 실험적으로 측정된 기포점 압력은 Peng-Robinson 상태방정식으로 계산한 결과와 매우 잘 일치하였다. 가변부피 투시창이 설치되어 있는 고압 상평형 실험장치는 고압의 압축유체 혼합물의 기포점을 매우 쉽고 빠르게 측정할 수 있는 방법이라고 할 수 있다.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2004년도 하계학술대회 논문집 C
• /
• pp.1802-1804
• /
• 2004

In seashore, outdoor insulators are polluted due to salty wind and the pollution causes the flashover and failure of electric equipments. As well known, the pollution has a close relation with meteorological factors such as wind velocity, precipitation, wind direction, relative humidity, dew point, etc. In this paper we statistically analyzed the correlation between the pollution and the meteorological factors including snowfall and freezing. The multiple regression analysis was used for the statistical analysis; daily measured equivalent salt deposit density(dependent variable) and the meteorological data(independent variable) were used. From the results of this investigation, we verified the influence of snowfall and freezing on the ESDD, which has been overlooked in the preceding investigation.

• 물과 미래
• /
• 제26권2호
• /
• pp.99-105
• /
• 1993

호우발생전의 기상상태, 유역의 저류상태 그리고 과거의 패턴을 반영한 실용성 있는 홍수 예보모형을 제안하였다. 호우 예보는 구름 물리학을 토대로한 지점 호우 예보 모형을, 유출예측은 저류함수모형을 채택하였다. 홍수 예보 모형의 입력 변수는 예보 발령 시점의 지상 기온, 지상 기압, 지상 이슬점 온도 그리고 유출점의 초기 유량이다. 홍수 예보 모형의 매개 상수는 과거의 홍수 사상이 갖는 최적 상수들의 산술평균값으로 하였다. 유출률은 홍수 초기 유량을 지표로 하여 예측될 수 있게 하였다.

• 한국표면공학회지
• /
• 제28권5호
• /
• pp.300-308
• /
• 1995

The effect of nitrogen finishing for the control of coating weight in a nitrogen sealing box on the coating surface property in hot dip galvanizing process has been studied. The coated surface is free of oxide marks and edge overcoated. The coating uniformity is excellent ; the standard deviation of the coating thickness along width of the specimen was $1~1.2\mu\textrm{m}$ in the box whereas $2.5~3\mu\textrm{m}$ in the air. Considering surface quality of the coating such as oxide mark, edge overcoated and zinc dust, the oxygen content between 40 and 200 ppm was suggested in the box in addition the oxygen content of at least 40 ppm or the minimum dew point of $-27^{\circ}C$ is required to prevent a zinc vaporization.

• 한국세라믹학회지
• /
• 제15권2호
• /
• pp.89-97
• /
• 1978

The basic mechanism of adherence in sintered high purity alumina ceramic-to-metal bonding was studied. Emphasis was placed on flux composition, porosity of the fired ceramics, and metallizing mixtures. The study was conducted on 95 and 99.5% alumina, using molydbenum-manganese, molybdenum-manganese-silicon dioxide metallizing compositions. Metallizing was performed in wet hydrogen (dew point, ＋17$^{\circ}C$) at 145$0^{\circ}C$ for 45min. This experiment indicated that adhernece mechanism of ultra high purity alumina ceramic was attributed to formation of $MnAl_2O_$4, and in the case of 95% alumina containing glass, the migration of glass from the interface into the void of the metal coating was the main role to the adhrence. It showed also that greater the bond-strength was resulted as porosity was increased.

• 한국환경과학회지
• /
• 제6권6호
• /
• pp.629-636
• /
• 1997

We have analyzed focusing on the characteristics, speed and width of sea breeze front in Pusan coastal area using the meteorological data observed at Kimhae air force meteorological station because the presence of the front has Important effects on the dInstributlon of air pollution. The inland penetration of sea breeze front was recognized by steep variation of meteorological parameters(wind direction, wind speed, temperature, dew point temperature, air pressure, relative humidity) before and after its passage and the variation of $SO_2$ concentration, the speed and width of the sea breeze front was 2.07m/s and 217m, respectively. The structure and inland penetration of sea breeeze front should be taken into account whenever a model is to be compared with detailed field measurements.

• 한국건축시공학회:학술대회논문집
• /
• 한국건축시공학회 2012년도 추계 학술논문 발표대회
• /
• pp.17-18
• /
• 2012

Moisture condensation leading to defects that occur repeatedly in the winter, and recognize the same method, the problem of the other buildings in the same area again and again, a vicious cycle that occurs due to the temporary lack of systematic research and processing way of coping has been recurring. In this study, as warming progresses, more inside the air-conditioned summer season due to an increase in the ambient temperature of the condensation phenomenon to happen about summer wall condensation phenomena are expected to analyze the case of a building to prevent condensation and for insulation designs are proposed.