• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.19 no.8
• /
• pp.1959-1964
• /
• 2015

This research was focused on the analysis of navigation parameters from the received L1, C/A signal of the recent GPS, which has advanced with the SA policy change and the GPS modernization policy by the United States. It was done as a first step study for a comprehensive analysis on the multiple satellite navigation systems which will be adding or separating GPS signal. In particular, the statistical analysis on the GDOP change and positional accuracy based on the geocentric and spherical coordinate systems were investigated with carrier- to-noise ratio and the satellite geometry, The obtained GDOP values of HDOP, PDOP, VDOP are 0.5, 1.2, and 1.1, respectively in deviation. In addition, the positioning accuracies with these GDOP values were analyzed in the ellipsoidal and ECEF coordinates.

• Journal of Korean Society of Coastal and Ocean Engineers
• /
• v.24 no.3
• /
• pp.159-165
• /
• 2012

In this study, a series of deposition tests have been performed using an annular flume and depositional parameters of natural cohesive sediments have been estimated domestically for the first time. The natural cohesive sediments for deposition tests have been collected from Kwangyang Bay and total 18 deposition tests have been carried out on different bed shear stress respectively but with the same initial concentration. Test results for natural cohesive sediments of Kwangyang bay show that minimum bed shear stress ${\tau}_{bmin}$, standard deviation ${\sigma}_1$, and time scale parameter $({\tau}_b^*-1)_{50}$ are $0.11N/m^2$, 0.68 and 0.85, respectively. Through the comparison with results of previous studies for other sediments, the results of this study are shown to be good enough to verify.

• Fire Science and Engineering
• /
• v.19 no.3 s.59
• /
• pp.70-75
• /
• 2005

The heat of combustion of polymer materials is an important fire characteristics, which can be used with other fire parameter to predict the potential fire hazard in the polymer handling process. The aim of this study is to predict the heat of combustion for polymers which used in the building interior materials. By using the literature data and multiple regression, the new equation for predicting the heat of combustion of polymers is proposed. The A.A.p.E.(average absolute percent error) and the A.A.D.(average absolute deviation) of the reported and the calculated heat of combustion by means of the oxygen consumption calorimeter and the stoichiometric coefficient were 4.46 and 1.09, and the correlation coefficient was 0.972. The values calculated by the proposed equations were in good agreement with the literature data. Therefore, it is expected that this proposed equations will support the use of the research for other polymer materials.

• The Journal of Advanced Prosthodontics
• /
• v.11 no.6
• /
• pp.331-340
• /
• 2019

PURPOSE. The purpose of this study is to assess the accuracy of three intraoral scanners along the complete dental arch and evaluate the feasibility of the assessment methodology for further in vivo analysis. MATERIALS AND METHODS. A specific measurement pattern was fabricated and measured using a coordinate measuring machine for the assessment of control distances and angles. Afterwards, the pattern was placed and fixed in replica of an upper jaw for their subsequent scans (10 times) using 3 intraoral scanners, namely iTero Element1, Trios 3, and True Definition. 4 reference distances and 5 angles were measured and compared with the controls. Trueness and precision were assessed for each IOS: trueness, as the deviation of the measures from the control ones, while precision, as the dispersion of measurements in each reference parameter. These measurements were carried out using software for analyzing 3-dimensional data. Data analysis software was used for statistical and measurements analysis (α=.05). RESULTS. Significant differences (P<.05) were found depending on the intraoral scanner used. Best trueness values were achieved with iTero Element1 (mean from 10 ± 7 ㎛ to 91 ± 63 ㎛) while the worst values were obtained with Trios3 (mean from 42 ± 23 ㎛ to 174 ± 77 ㎛). Trueness analysis in angle measurements, as well as precision analysis, did not show conclusive results. CONCLUSION. iTero Element1 was more accurate than the current versions of Trios3 and True Definition. Importantly, the proposed methodology is considered reliable for analyzing accuracy in any dental arch length and valid for assessing both trueness and precision in an in vivo study.

• Korean Journal of Air-Conditioning and Refrigeration Engineering
• /
• v.11 no.1
• /
• pp.91-99
• /
• 1999

Vapor-liquid equilibrium apparatus is designed and set up. The equilibrium data of two binary systems, HFC-32/143a and HFC-143a/134a, are measured. Fifteen equilibrium data for HFC-32/143a and HFC-143a/134a systems are measured over the temperature range 263.15~283.15K at 10K interval and the composition range 0.10~0.80, respectively. And vapor-liquid equilibrium data are calculated using equation of state and correlation of activity coefficient and compared with the present data. Equation of state is used CSD and RKS equations and correlation of activity coefficient is used Margules' and Van Ness and Abbott's correlations. Real behavior of HFC-32/143a system has very large deviation with Raoult's rule which is ideal behavior. But real behavior of HFC-143a/134a system is similar to ideal behavior. The calculated data from CSD equation are compared with the data in the open literatures and the calculated data from REFPROP. In the results for REFPROP, the relative deviations of bubble point pressure for HFC-32/143a system are within -2.16~0.84% for CSD equation and within -0.20~1.10% for RKS equation. And the relative deviations of bubble point pressure for HFC-143a/134a system are within -0.45~0.12% and -0.20~2.8% for CSD and RKS equations, respectively.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.10 no.2
• /
• pp.39-45
• /
• 2006

In liquid rocket engine turbopump, it is difficult to evaluate turbine performance for high pressure, high temperature circumstance. Turbine test is often done by using air at similarity condition so that the turbine can be tested at lower risk. This paper describes an air similarity test program of liquid rocket engine turbopump turbine. A test facility has been built to evaluate aerodynamic performance of turbines. The test facility consists of high pressure air supply system, mass flow rate measuring nozzle, test section, hydraulic break, exit orifice for pressure control, instrumentation and control system. This paper also presents how to decide the similarity conditions of the turbine test and describes how to control test conditions. Relative standard deviation of measurement parameter was less than 1% and measured turbine efficiency corresponded with analysis result within 2%.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.22 no.9
• /
• pp.2043-2052
• /
• 1997

The object-oriented coding technique which is one of the coding methods in very low bit rate environment is suitable for videophone image sequence. The selection of source model affect image analysis. In this paper, an image analysis method for the object-oriented coding is presented. The process is composed of changed region detection andmotion estimateion. First, we use the standard deviation of frame difference as thrreshold to extract themoving area. If thesum of gray values in mask is greater than the threshold, the center pixel of the mask is regarded as moving region. After moving is detected in changed region by edge operator, observation point is determined from moving region. The motion is estimated by 6-parameter mapping method with determined observation point. The experimantal resutls show that the proposed method can significantly improve the image quality.

• The Transactions of the Korean Institute of Electrical Engineers A
• /
• v.49 no.3
• /
• pp.95-106
• /
• 2000

The load frequency control of power system is one of important subjects in view of system operation and control. That is even though the rapid load disturbances were applied to the given power system, the stable and reliable power should be supplied to the users, converging unconditionally and rapidly the frequency deviations and the tie-line power flow one on each area into allowable boundary limits. Nonetheless of such needs, if the internal parameter perturbation and the sudden load variation were given, the unstable phenomenal of power system can be often brought out because of the large frequency deviation and the unsuppressible power line one. Therefore, it is desirable to design the robust neuro-fuzzy controller which can stabilize effectively the given power system as soon as possible. In this paper the robust neuro-fuzzy controller was proposed and applied to control of load frequency over multi-area power system. The architecture and algorithm of a designed NFC(Neuro-Fuzzy Controller) were consist of fuzzy controller and neural network for auto tuning of fuzzy controller. The adaptively learned antecedent and consequent parameters of membership functions in fuzzy controller were acquired from the steepest gradient method for error-back propagation algorithm. The performances of the resultant NFC, that is, the steady-state deviations of frequency and tie-line power flow and the related dynamics, were investigated and analyzed in detail by being applied to the load frequency control of multi-area power system, when the perturbations of predetermined internal parameters. Through the simulation results tried variously in this paper for disturbances of internal parameters and external stepwise load stepwise load changes, the superiorities of the proposed NFC in robustness and adaptive rapidity to the conventional controllers were proved.

• Spatial Information Research
• /
• v.19 no.2
• /
• pp.29-36
• /
• 2011

This study performed quantitative assessment of the performance of adjustment models by a-priori analysis of the statistics of the surface parameter estimates against modeling factors. Lidar, airborne imagery, and SAR imagery have been used to acquire the earth surface elevation, where the shape properties of the surface need to be determined through neighboring observations around target location. In this study, parameters which are selected to be estimated are elevation, slope, second order coefficient. In this study, several factors which are needed to be specified to compose adjustment models are classified into three types: mathematical functions, kernel sizes, and weighting types. Accordingly, a-priori standard deviations of the parameters are computed for varying adjustment models. Then their corresponding confidence regions for both the standard deviation of the estimate and the estimate itself are calculated in association with probability distributions. Thereafter, the resulting confidence regions are compared to each other against the factors constituting the adjustment models and the quantitative performance of adjustment models are ascertained.

• Journal of Fisheries and Marine Sciences Education
• /
• v.28 no.2
• /
• pp.525-538
• /
• 2016

This study is to investigate the effect of the amusement factor and the motive of participation in skin-scuba class on the satisfaction with university life with the university students participating in the skin-scuba class and to provide the practical research data for the development of the marine sports, for the proper operation of skin-scuba class, and for the leisure life which the university students may lack. For these purposes, technical statistics between questions were disposed in order to grasp the average and standard deviation on each variables, exploratory factor analysis and reliability analysis were conducted for the reliability and validity of the scale, and correlation analysis and multiple regression analysis were conducted to test the casuality of amusement factor, the motive of participation in skin-scuba class and the satisfaction with university life as the research methods. Research results showed that it was confirmed that the amusement factor and the motive of participation in skin-scuba class act as the important variables in the satisfaction with university life and it was predicted that the motive of participation in skin-scuba class and the amusement factor had interrelation with parameter. Therefore, a variety of programs reflecting the amusement factors should motivate the university students to particiapte in the skin-scuba class to increase the satisfaction with university life and to encourage the re-participation of students.