• 한국콘텐츠학회논문지
• /
• 제18권1호
• /
• pp.232-240
• /
• 2018

본 연구는 자동노출제어장치의 감도변화에 따른 흡수선량의 변화와 히스토그램을 이용하여 검출기 성능평가 방법을 제안하고자 하였다. 실험방법은 두개부, 복부, 골반부위 별로 검출기 감도 S200, S400, S800, S1000의 흡수선량을 측정하여 검출기의 정확성을 평가하였다. 또한 영상의 히스토그램 분석을 통하여 검출기의 감도별 동적범위를 평가하였다. 그 결과 부위 별 흡수선량은 감도가 S200에서 S1000으로 높게 설정될수록 흡수선량이 단계적으로 감소하였다. 감도 별 히스토그램을 분석한 결과 두개부는 감도가 높게 설정될수록 히스토그램의 양단의 정보량이 상실되는 결과를 보였다. 복부와 골반부는 감도가 높게 설정될수록 히스토그램의 첫부분의 정보량이 상실되는 언더플로우 현상을 보였다. 결론적으로 검출기가 감도의 변화는 정확하게 구현해 내었으나 검출기 성능저하로 인한 자동노출제어장치의 감도변화에 따른 영상의 동적범위는 제대로 구현해내지 못한다는 것을 알 수 있었고 검출기의 성능평가 시 흡수선량과 히스토그램을 통한 평가가 유용하다는 것을 알 수 있었다.

• Transactions on Electrical and Electronic Materials
• /
• 제3권4호
• /
• pp.16-20
• /
• 2002

The high bias voltage associated with the thick layer (typically 500-1000 ㎛) of selenium required to have an acceptable x-ray absorption in radiography and fluoroscopy applications may have some practical inconvenience. A hybrid x-ray detector with zinc sulfide-amorphous selenium structure has been developed to improve the x-ray sensitivity of a a-Se based flat-panel digital imaging detector. Photoluminescence(PL) characteristic of a ZnS:Ag phosphor layer showed a light emission peak centered at about 450 nm, which matches the sensitivity spectrum of selenium. The dark current of the hybrid detector showed similar characteristics with that of a a-Se detector. The x-ray sensitivity of hybrid and a-Se x-ray detector was 345 pC/㎠/mR and 295 pC/㎠/mR at an applied voltage of 10 V/㎛, respectively. The purpose of this study was to evaluate the pertinence of a solution using a thin selenium layer, as a photosensitive converter, with a thick coating of silver doped zinc sulfide phosphor.

• Transactions on Electrical and Electronic Materials
• /
• 제4권3호
• /
• pp.10-14
• /
• 2003

In this paper, we have introduced the x-ray detector built with a CsI:Na scintillation layer deposited on amorphous selenium. To determine the thickness of the CsI:Na layer, we have estimated the transmission spectra and the absorption of continuous x-rays in diagnostic range by using computer simulation (MCNP 4C). A x-ray detector with 65 ${\mu}m$-CsI:Na/30 ${\mu}m$-Se layer has been fabricated by a thermal evaporation technique. SEM and PL measurements have been performed. The dark current and x-ray sensitivity of the fabricated detector has been compared with that of the conventional a-Se detector with 100 ${\mu}m$ thickness. Experimental results show that both detectors exhibit a similar dark current, which was of a low value below $400 pA/cm^2$ at 10 V/${\mu}m$. However, the CsI:Na-Se detector indicates high x-ray sensitivity, roughly 1.3 times that of a conventional a-Se detector. Furthermore, a CsI:Na-Se detector with an aluminium reflective layer shows a 1.8 times higher x-ray sensitivity than an a-Se detector. The hybrid type detector proposed in this work exhibits a low dark current and high x-ray sensitivity, and, in particular, excellent linearity to the x-ray exposure dose.

• 한국화재소방학회논문지
• /
• 제28권6호
• /
• pp.58-61
• /
• 2014

불꽃감지기는 열, 연기식 감지기보다 화재검출이 빠르고 높은 층고에서도 효과를 발휘할 수 있어 가격이 고가임에도 많이 사용되고 있다. 불꽃감지기의 동작신뢰성 향상을 위해 성능시험, 감도시험, 옥내 외구분, 제품사후관리나 관리감독에 대하여 외국 기준과 비교하였다. 그 결과 유럽과 미주지역에는 부작동시험, 옥내 외구분이 없고 감도조정 기준이 있다. 성능시험중 작동관계는 제품의 신뢰성이나 내구성에 중심을 두고, 부작동시험은 현장의 환경에 맞게 감도를 조정할 수 할 수 있게 한다. 또한 제품사후관리 조항 추가 및 제품에 대한 품질관리 책임과 인증기관의 관리시스템, 특수감지기의 제도권 도입, 상호 관련기구들의 규정 마련이 필요하다.

• Nuclear Engineering and Technology
• /
• 제54권12호
• /
• pp.4652-4659
• /
• 2022

Among the detector materials available at room temperature, thallium bromide (TlBr), which has a relatively high atomic number and density, is widely used for gamma camera imaging. This study aimed to verify the usefulness of TlBr through quantitative evaluation by modeling detectors of various compound types using Monte Carlo simulations. The Geant4 application for tomographic emission was used for simulation, and detectors based on cadmium zinc telluride and cadmium telluride materials were selected as a comparison group. A pixel-matched parallel-hole collimator with proven excellent performance was modeled, and phantoms used for quality control in nuclear medicine were used. The signal-to-noise ratio (SNR), contrast to noise ratio (CNR), sensitivity, and full width at half maximum (FWHM) were used for quantitative analysis to evaluate the image quality. The SNR, CNR, sensitivity, and FWHM for the TlBr detector material were approximately 1.05, 1.04, 1.41, and 1.02 times, respectively, higher than those of the other detector materials. The SNR, CNR and sensitivity increased with increasing detector thickness, but the spatial resolution in terms of FWHM decreased. Thus, we demonstrated the feasibility and possibility of using the TlBr detector material in comparison with commercial detector materials.

• 한국의학물리학회지:의학물리
• /
• 제27권4호
• /
• pp.236-240
• /
• 2016

The purpose of this study is to propose a novel high sensitivity neuro-PET design. The improvement of sensitivity in neuro-PET is important because it can reduce scan time and/or radiation dose. In this study, we proposed a novel PET detector design that combined conical shape detector with cylindrical one to obtain high sensitivity. The sensitivity as a function of the oblique angle and the ratio of the conical to cylindrical portion was estimated to optimize the design of brain PET using Monte Carlo simulation tool, GATE. An axial sensitivity and misplacement rate by penetration of ${\gamma}$ rays were also estimated to evaluate the performance of the proposed PET. The sensitivity was improved by 36% at the center of axial FOV. This value was similar to the calculated value. The misplacement rate of conical shaped PET was about 5% higher than the conventional PET. The results of this study demonstrated the conical detector proposed in this study could provide subsequent improvement in sensitivity which could allow to design high sensitivity PET for brain imaging.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2002년도 춘계학술대회 논문집 센서 박막재료 반도체재료 기술교육
• /
• pp.31-34
• /
• 2002

In this paper, the electric properties of amophous selenium multilayer samples has been investigated. In order to develop the hybrid flat-panel digital· X-ray image detector, we measured and analyzed their performance parameters such as the X -ray sensitivity and dark-current for a amophous selenium multilayers X-ray detector with a phosphor layer, The hybrid digital X-ray image detector can be constructed by integrating a phosphor layer (or a scintillative layer) that convert X-ray to a light on a-Se photoconduction mulilayers that convert a light to electrical signal. As results, the dielectric materials such as parylene between the phosphor layer and the top electrode may reduce the dark-current of the samples. Amorphous selenium multilayers having dielectric layer(parylene) has characteristics of low dark-current, high X-ray sensitivity. So we can acquired a enhanced signal to noise ratio. In this paper offer the method can reduce the dark-current in the hybrid X-ray detector.

• 대한방사선기술학회지:방사선기술과학
• /
• 제44권5호
• /
• pp.459-464
• /
• 2021

The detector performance is important role in acquiring the gamma rays from patients. Among parameters of detector performances, there is density, which relates to respond to gamma rays. Therefore, we confirm the detection efficiency according to various detector materials based on the density parameter using GATE (geant4 application for emission tomography) simulation tool. The NaI (density: 3.67 g/cm³), CZT (Cadimium Zinc Telluride) (density: 5.80 g/cm³), CdTe (Cadmium Telluride) (5.85 g/cm³), and GAGG (Gadoinium Aluminum Gallium Garnet) (density g/cm³) were used as detector materials. In addition, the point source and quadrant bar phantom, which is modeled for 0.5, 1.0, 1.5, and 2.0 mm thicknesses, were modeled to confirm the quatitative analysis using sensitivity (cps/MBq) and the full width at half maximum (FWHM, mm) at the 2.0 mm bar thickness containing visual evaluation. Based on the results, the sensitivity for NaI, CZT, CdTe, and GAGG detector materials were 0.12, 0.15, 0.16, and 0.18 cps/MBq. In addition, the FWHM for quadrant bar phantom in the 2.0 mm bar thickness is 3.72, 3.69, 3.70, and 3.73 mm for NaI, CZT, CdTe, and GAGG materials, respectively. Compared with performance of detector materials according to density, the high density can improve detection efficiency in terms of sensitivity and mean count. Among these detector materials, the GAGG material is efficient for detection of gamma rays.

• Nuclear Engineering and Technology
• /
• 제56권3호
• /
• pp.916-921
• /
• 2024

The control rod worth sensitivity to the neutron detector position in the rod drop experiment is studied by the time-dependent Monte Carlo (TDMC) neutron transport calculations for AGN-201K educational reactor and the Kyoto University Critical Assembly. The TDMC simulations of the rod drop experiments are conducted by the Seoul National University Monte Carlo (MC) code, McCARD, yielding time-dependent neutron densities at detector positions. The detector-position-dependent results of the total control rod worth calculated by the extrapolation, the integral counting, and the inverse methods are compared with the numerical reference using the MC eigenvalue calculations and the experimental results. From these comparisons, it is observed that the total control rod worth can be estimated with a considerable difference depending on the detector position through the rod drop experiment. The proposed TDMC simulation of the rod drop experiment can be applied for searching a better detector position or quantifying a bias for the control rod worth measurement.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 1996년도 추계학술대회 논문집
• /
• pp.417-420
• /
• 1996

We have investigated air/200ppm NO$_2$ gas-detector characteristics of using CuTBP (Copper-tetra-tert-butylphthalocyanine) chemiresistor devices. The CuTBP films were made by Langmuir-Blodgett (LB) techniques. Sensitivity, response time, recovery time, and repoducibility of the devices were measured by current-voltage characteristics. To increase sensitivity, interdigital electrode was used. It was found that a conductance G increases monotonically as the number of interdigital electrode increases, and a Sensitivity, Reproducibility is stable. As far as a current is concerned, the current when N=25 is greater than that when N=1 by 70 or so. It indicates that the number of interdigital electrodes affects the current, sensitivity and stability We have also investigated applicability of the CuTBP chemiresistor device for a gas detector.