• 에너지공학
• /
• 제12권3호
• /
• pp.177-183
• /
• 2003

본 논문은 방사능조사의 조건하에서의 설계조건을 만족해야 하는 fuel rod의 설계응력값을 검증하는데 그 목적이 있다. 이 경우에, 안전성에 있어서 열에 의한 영향이 가장 주된 고려조건이 된다. 그러나 이러한 열영향이 고려된 해석은 구조물의 안전성해석에서 비교적 간단히 해결되는 문제가 아니다. 여기서는 이론적 해석을 통한 접근방식으로 보수적인 관점에서 fuel rod의 설계에 적용되는 설계 응력값을 검증하고자 하였다. 추후에 시도하는 fuel rod의 설계에 있어서 본 해석방법을 이용하면 안전설계의 검증을 위한 이론적 접근방법의 하나로 이용할 수 있을 것으로 사료된다.

• 한국해양공학회지
• /
• 제25권1호
• /
• pp.27-31
• /
• 2011

The previously developed method of estimating the propulsion performance of a UUV was applied to the high speed UUV, which is propelled by commercial thrusters. The thrusters were selected with an overdesign mentality; in other words, their capacities were excessive. At that point, the designer's concern was focused on a question regarding at what rpm the UUV could reach the design speed. Because the developed method required thrust coefficient curve data, the researchers asked for the POW data of the thrusters from the manufacturer. From the data, the researchers extracted the thrust coefficient and estimated the rpm value of design speed for the UUV. Finally, the researchers compared the estimated value and the result from a self-propulsion test using a VPMM (Vertical planar motion mechanism) test at a towing tank in MOERI.

• 한국해안·해양공학회논문집
• /
• 제28권5호
• /
• pp.292-302
• /
• 2016

본 연구에서는 동해안의 4개 정점(속초, 묵호, 후포, 진하)에서 13년간 관측된 파랑자료를 이용하여 극치확률분석을 통해 재현빈도별로 천해설계파를 산정하였고, 이 값을 한국해양연구원(2005)에 제시된 동해안 심해설계파를 이용하여 SWAN 수치모델링로 계산된 결과와 비교하였다. 그 결과 2005년 기존 심해설계파의 수치실험 결과는 관측파랑에 의한 극치분석 결과보다 상대적으로 작은 것으로 나타났으며, 특히 30년 빈도 이하에서 동해안에서의 기존 심해설계파고가 과소산정되었을 가능성이 있음을 시사한다.

• 한국지진공학회:학술대회논문집
• /
• 한국지진공학회 2002년도 추계 학술발표회 논문집
• /
• pp.189-196
• /
• 2002

The capacity of CFS piers has not been used to a practical design, because there is no guide of a seismic design for CFS piers. Therefore, the guide of a seismic design value is derived from tests of CFS piers in order to apply it to a practical seismic design. Steel piers and concrete-filled steel piers are tested with constant axial load using quasi-static cyclic lateral load to check ductile capacity and using the real Kobe ground motion of pseudo-dynamic test to verify seismic performance. The results prove that CFS piers have more satisfactory ductility and strength than steel piers and relatively large hysteretic damping in dynamic behaviors. The seismic performance of steel and CFS piers is quantified on the basis of the test results. These results are evaluated through comparison of both the response modification factor method by elastic response spectrum and the performance-based design method by capacity spectrum and demand spectrum using effective viscous damping. The response modification factor of CFS piers is presented to apply in seismic design on a basis of this evaluation for a seismic performance.

• 한국시뮬레이션학회논문지
• /
• 제10권2호
• /
• pp.1-14
• /
• 2001

The layout design of component plays an important role in the design and usability of many engineering products. The Engineering artifacts of today are becoming increasingly complicated. The simulated annealing method has been applied effectively to the layout and packing problems of wafer. The main characteristics of simulated annealing method is that an optimum can be obtained from the many local optimums by controlling the temperature and introducing the statistic flickering. The objective of this study is to suggest a method to apply the simulated annealing method to the three dimensional layout design of submergible boat which has multiple constraint conditions and evaluation criteria. We describe an approach to define cost function, constraints and generate layouts using a computer. In this research three dimensional LAYout Design Optimization Program(LAYDOP ver.2) has been developed. The layout result(the total value of evaluation criteria) designed by a human layout expert has been improved by 31.0% using this program.

• 한국생산제조학회지
• /
• 제24권2호
• /
• pp.186-191
• /
• 2015

Presently, rapidly changing and unstable global economic environments demand engineers. Products should be designed to increase profits by lowering costs and provide distinguished performance compared with competitors. This study aims to optimize the design of the power-transmission drive shaft. The mass is reduced as an objective function, and the stress is constrained under a constant value. To reduce the number of experiments, CCD (central composite design) and D-Optimal are used for the experimental design. RSM (response surface methodology) is employed to construct a regression model for the objective functions and constraint function. In this problem, there is only one objective function for the mass. The other objective function gives 1; thus, NSGA-II is used.

• 기술발표회
• /
• 통권2006호
• /
• pp.311-319
• /
• 2006

Artesian Pressure exists in Hwa Jeon Project Site of Nakdong Delta Area. Maxium value of the pressure ranges between 06 tonf/m2 and 1 3 tonf/m2 in the design site. This paper presents a design case study considering the Artesian Pressure to calculate the consolidation settlement of the deep marine clay.

• Current Photovoltaic Research
• /
• 제11권1호
• /
• pp.34-37
• /
• 2023

Solar energy had become the main energy industry of renewable energy along with hydroelectric power generation. One of the technologies that contributed to the popularization of photovoltaic power and the decrease in the unit price of photovoltaic modules was the large-area solar cell. However, as the area increased, the light receiving area increased and the current value increased accordingly. Since power loss occurs when the current value was large, the number of busbar was increased to increase the current collection rate, and a technology to lower the current value through half-cutting was developed. The bus bar of the solar cell served as a passage through which the generated current was transmitted. This was because when the number of busbar decreases, the moving distance of electrons increased, so the amount of power generation decreases and when it increases, shadows occured. An important aspect of the electrode design was the optimal balance of these busbars and number of fingers. Therefore, in this study, the characteristics of the solar cell according to the number of front bus bars of the large-area solar cell were simulated using Griddler 2,5 pro. After selecting the number of busbar with the best characteristics, the difference was compared by varying the number of fingers and a better direction for the number of cutting was presented.

• 산업경영시스템학회지
• /
• 제45권3호
• /
• pp.131-138
• /
• 2022

The demand for chiller equipment that keeps each machine at a constant temperature to maintain the best possible condition is growing rapidly. PID (Proportional Integral Derivation) control is a popular temperature control method. The error, which is the difference between the desired target value and the current system output value, is calculated and used as an input to the system using a proportional, integrator, and differentiator. Through such a closed-loop configuration, a desired final output value of the system can be reached using only the target value and the feedback signal. Furthermore, various temperature control methods have been devised as the control performance of various high-performance equipment becomes important. Therefore, it is necessary to design for accurate data-driven temperature control for chiller equipment. In this research, support vector regression is applied to the classic PID control for accurate temperature control. Simulated annealing is applied to find optimal PID parameters. The results of the proposed control method show fast and effective control performance for chiller equipment.

• 대한산업공학회지
• /
• 제2권1호
• /
• pp.61-78
• /
• 1976

The purpose of this study is to establish the horizontal and vertical working area which is dependent on measuring value of workers, body in order to make easy and stable working environments, and then to design the size of machines, tools and instruments in production factory because of making the practical production conditions which is the most suitable to human characteristics. But there is necessity that we have to review numeric value of measurement periodically because the size of workers' body is variable according to periodic and social circumstances. The establishment of standard working area after measurement enable us to make the best working conditions and we can design standard working table, optimum size of all machines and tools in production activity. Therefore, we can also acknowledge the importance of studying on human engineering because human engineering is necessary to reduction of fatigue in working, saving workers from industrial accidents, fail-safe system, improvement of productivity with increase in efficiency and etc. Finally, this study informs us that numeric value of measurement is larger than that of Japan, but not than that of America and Germany. So we can establish standard working area which is the most suitable for Korean inherence after measurement of detailed parts for workers' body.