• Journal of the Korean Society of Manufacturing Technology Engineers
• /
• v.20 no.4
• /
• pp.495-501
• /
• 2011

The purpose of this study is to improve the roundness of CNC turning so that helps the operator to choose the right turning conditions to produce a product with the given parameters. This paper focuses on determining the optimal levels of machining factors for circular shaft with CNC turning. For this purpose, the optimization of factors is performed based on experimental design method. A design and analysis of experiments are conducted to study the effects of these factors on the roundness by using the SIN ratio, analysis of ANOVA, and F-test. Factors, namely, fixed pressure, wall thickness, depth of cut, and feed rate are optimized with consideration of the roundness. The boring tool used in this study is a tungsten carbide coated. The material of workpiece is Al6061 and the machining method is dry cutting.

• International Journal of Safety
• /
• v.3 no.1
• /
• pp.10-14
• /
• 2004

Apar The dynamic characteristics of the current collection system are evaluated during a test run. Signals from accelerometers attached to the pantograph assembly are acquired through a measurement system and analyzed. It is found that the train speed significantly influences the magnitude and frequency characteristics of the pantograph motion. The major frequency components of interest are found to be frequency components originating from the motion of the train along the catenary as well as the several resonance frequencies of the structural vibration of the pantograph. The contact force is also calculated by assuming the pantograph panhead as a rigid structure.

• Journal of Ship and Ocean Technology
• /
• v.1 no.1
• /
• pp.26-34
• /
• 1997

Under water wet welding is an economically alternative for the repair of offshore structures. In this paper investigations on the fatigue strength of a wet welded pipe structural member have been reported. For the connection a special sleeve patch design has been developed. The joint was fatigue tested. The evaluation of the test was carried out by means of the hot-spot approach with regard to several extrapolation rules of the hot-spot stress. Obtained results have been compared to actual classfication rules and recommendations.

• Special Issue of the Society of Naval Architects of Korea
• /
• 2017.10a
• /
• pp.63-66
• /
• 2017

All passenger ships aboard more than 36 passengers are to be able to easily find escape routes when the escape way by fire with flame spread were onboard vessel (incl. Ferry, Passenger, Ro-pax, Inland Ferry) It should be impossible by ordinary emergency lights. The international Maritime Organization (IMO) gives special requirement for luminescent evaluation onboard test procedure and applicable location of low location lighting. In order to maintain the residual light source for a certain time in the low location lighting with a strip-shaped light source, the light source material must be sufficiently exposed to the light due to the proper placement of the escape route. The lighting arrangement influence how maintain low location lighting strip luminescent which measured onboard in connection with what elements are mainly sustain luminescent.

• Journal of the Korean Institute of Telematics and Electronics A
• /
• v.33A no.10
• /
• pp.48-60
• /
• 1996

This paper focuses on the necessities of interworking and dervation of the requirements of interworking system for interworking between 64 Kbps based N-ISDN (narrowband ISDN) and B-ISDN(broadband ISDN). Furthermore, the design and the implementation of IWF (interworking function) are presentd. We analyze two ISDN signalling systems, and propose the architecture of interworking system. And then we make the baisc call procedure model between N-ISDN and B-ISDN, and verify the dynamic behaviors through the reachability tree of petri net. IWF is designed and implemented for transforming the differences between the two signalling systems. The operational confirmity of th eimplemented program was confirmed by the local test method. The performance of IWF was evaluated throguh the simulation language SLAM-II. As the result of evaluation shows, we confirm that the processing delay is maintained within 3 ms under the utilization 0.9.

• Proceedings of the Korea Concrete Institute Conference
• /
• 2003.11a
• /
• pp.223-228
• /
• 2003

Results of 61 framed reinforced concrete shear walls with openings were reviewed to evaluate the current design provisions for nominal shear strength. Provisions for ACI 318-02 and AIJ Code pertaining to shear design of shear walls evaluated the applicability of shear walls with openings subjected to lateral and vertical loads. Evaluation of test results indicates that the nominal unit shear strength($\Psi$=1.0) calculated using the provisions of ACI and AIJ does not represent the observed shear strength well. Based on the limited database considered in this study, A reasonable lower bound to the shear strength of high-strength concrete shear walls is found to be $1.09\sqrt{f_{cu}}$ kgf/$\textrm{cm}^2$.

• International Journal of Concrete Structures and Materials
• /
• v.2 no.2
• /
• pp.115-122
• /
• 2008

Ductility is important in the design of reinforced concrete structures. In seismic design of reinforced concrete members, it is necessary to allow for relatively large ductility so that the seismic energy is absorbed to avoid shear failure or significant degradation of strength even after yielding of reinforcing steels in the concrete member occurs. Therefore, prediction of the ductility should be as accurate as possible. The principal aim of this paper is to present the basic data for the ductility evaluation of reinforced high-strength concrete beams. Accordingly, 23 flexural tests were conducted on full-scale structural concrete beam specimens having concrete compressive strength of 40, 60, and 70MPa. The test results were then reviewed in terms of flexural capacity and ductility. The effect of concrete compressive strength, web reinforcement ratio, tension steel ratio, and shear span to beam depth ratio on ductility were investigated experimentally.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2003.06a
• /
• pp.107-112
• /
• 2003

The recent machine tools are requested so high-quality processing and productivity increasing. Therefore, it is so necessary to develop technology for high-speed and high-precision. This thesis touches on the development of high speed and intellectual line center. At first, the line center is necessary that strong structure, compact structure and light weight design for high-speed processing and transfer. So, it is necessary that examination of new materials and structures for light-weight and control devices for precision processing. So, it is going to make mention of the process of 1st model production for the above-mentioned based on test model production and evaluation.

• Special Issue of the Society of Naval Architects of Korea
• /
• 2006.09a
• /
• pp.71-76
• /
• 2006

Preliminary conceptual design of hulls is developed and a theoretical evaluation study performed for the comparison of the hull concepts. Systematic variation of the side hull location is carried out to find an optimum position of side hulls for a trimaran by CFD computation. In order to compare computed results, the model test of trimaran was carried out. Shallow water effect is considered due to the route which has critical water depth of 20m for the design speed and investigated on the condition of different speeds and water depth by the numerical computations.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2000.05a
• /
• pp.591-594
• /
• 2000

In the recent day, fatigue life prediction techniques play a major role in the design of components in the ground vehicle industry. Full scale durability testing in the laboratory is an essential of any fatigue life evaluation of components or structure of the automotive vehicle. Component testing is particulary important in today's highly competitive industries where the design to reduce weight and production costs must be balanced with the necessity to avoid expensive service failure. Generally, 3-axis durability testing device is used to carry out the fatigue test. In this paper, The operation software for simultaneously driving 3-axis vibration testing device is developed and the displacement of the 3-axis actuator is separately calibrated by LDT Moreover, the input and output data are displayed in windows of PC controller with real time.