• Transactions of the Korean hydrogen and new energy society
• /
• v.32 no.6
• /
• pp.636-641
• /
• 2021

Using numerical analysis, various factors influencing the performance development of high-pressure pumps for Dimethyl Ether (DME) engines were identified and the impact of each factor was evaluated using Taguchi method. DME fuels are more compressive than diesel fuels and have the lower heat generation, so it is necessary to increase the size of the plunger and speed (RPM) of the pump as well. In addition, it is necessary to change the shape and design of control valve to control the discharge flow and pressure. In this study, various variables affecting the performance and flow rate increase of high-pressure pumps for DME engines are planned using Taguchi method, and the best design method is proposed using correlation of the most important variables. As a result, we were able to provide the design value needed for a six-liter engine and provide optimal conditions. The best combination factors to optimize the flow rate at RPM 2,000 and diameter plunger with 20 mm. The regression equation can also be used to optimize the flow rate; -8, 13+0, 2552 RPM +54, 17 diam. Plunger.

• Journal of Korea Trade
• /
• v.25 no.3
• /
• pp.48-64
• /
• 2021

Purpose - This study examined the effect of tariff cuts on productivity in Korea's manufacturing industries and the effect of initial productivity level before tariff cuts on productivity improvement after tariff cuts. We also attempted to identify whether import-driven or export-driven factors are more important for productivity improvement, especially in low productivity industries. Design/methodology - Since tariff reduction is a policy decision that can affect cross-industry, its impact is spread across all industries beyond the scope of a single firm through the input and output network of industry structure. Accordingly, we proposed a new method to measure the change in productivity to reflect the impact of tariff cuts across industries. Through an Armington CGE analysis, changes in endogenous variables can be directly measured after the exogenous shock of tariff reduction, and the amount of movements in productivity triggered by tariff cuts can also be calculated. We can thus assess the effectiveness of exogenous policy, such as tariff cuts, through the difference between the benchmark and counterfactual values of endogenous variables. Findings - This study confirmed that tariff reduction positively affected productivity improvement in Korea's manufacturing industries. It also confirmed that productivity gains occur in Korea's leading export industries. Finally, greater productivity gains were recorded in the group with additional high-export-share or high-import-share conditions for low productivity industries. These results are, in a limited sense, consistent with the existing studies that emphasize the importance of exports and imports on productivity improvement, especially for low productivity industries. Originality/value - The results of our experiments are different from those of non-CGE studies, which measure the industry-level change in productivity with dummy coefficients, in terms of directly calculating the amount of change in productivity. In addition, we propose that the Armington CGE model is more appropriate than the Melitz CGE model to directly measure the productivity after tariff cuts. This is because the Melitz CGE model assumes the given specific productivity density, which does not change after an overall drop of tariffs. To the best of our knowledge, this approach to directly calculating productivity by reflecting the impact of tariff reduction across industries through CGE analysis, is unprecedented in this literature.

• Journal of the Korea Concrete Institute
• /
• v.26 no.3
• /
• pp.267-275
• /
• 2014

Recently, the construction of curved bridge has increased, thus researchers perform the analytic studies on PSC curved bridge. However, the grid analysis method that are mostly used in the construction industry is not adequate to acquire the precise behavior evaluation of curved PSC briges. Therefore, the precise finite element analysis considering the effective variables were performed to establish the basis for the design method of curved PSC bridge by using 3D elements and bar element. The evaluated variables in this analysis were the number of girders, loading point, section figure, change of prestressing force. The results show the load carrying capacity of the 3 girder type bridge is 200% of that of the 2 girder type, and that applying load on outer girder makes the load resistance capacity and the deflection deviation of 2 girders smaller. The structural capacity of the bridge is improved when the section size is increased, but the efficiency of it is not sufficient enough compare to that of the change of prestressing forces. The change of prestressing forces shows that the camber and the load carrying capacity are linearly increased as PS force is increased. Moreover, when the PS force applied on outer girder is increased than that of inner girder, the deviation of deflection the girders decreases, thereby the stability of the bridge is enhanced.

• Journal of the Korean Society for Precision Engineering
• /
• v.7 no.3
• /
• pp.26-36
• /
• 1990

This paper describes the Computer Aided Design (CAD) of dies for direct hot extrusion of structural shapes such as Z's and U's from aluminum alloys. A simple analysis of the direct extrusion process is developed and used to formulate a disign procedure for determining the optimal shape of the extrusion dies. A computer software system has been developed to design flat-faced dies for non-lubricated hot extrusion process. This software is a system of computer programs which are written to logical design procedure. Computer programs are based on empirical and analytical relationships, as well as on established knowledge based system. In the interactive mode of operation, the reaults at various tages of the design process are plotted on a screen. At any stage, the designer can interact with the computer to change or modify the design, based on his experience. The output from the program is (a) the design of the flat-faced die, (b) information on extrusion load, reduction ratio, and other process variables, etc. The implementation of this CAD system is expected to (a) provide scientific basis and rationalize the die design procedure, (b) optimize extrusion variables to maximize yield and production rate, (c) improve utilization of existing press capacity, etc.

• The Journal of Industrial Distribution & Business
• /
• v.11 no.4
• /
• pp.7-18
• /
• 2020

Purpose: This research investigates the impact of technology adoption on organisation productivity. The framework has three independent variables viz. technological change, information technology (IT) infrastructure, and IT knowledge management and one dependent variable as organisational productivity. Research design, data and methodology: An explanatory research design with a quantitative research method was employed, and data was collected using a self-administered questionnaire using online as well as an offline survey. The sample consisted of 300 IT managers and senior-level executives (production as well as service team) in leading IT companies in Malaysia selected using snowball sampling. Normality and reliability assessment was performed in the first stage utilising SPSS 22, and Confirmatory Factory Analysis (CFA) was performed with maximum likelihood estimation to assess the internal consistency, convergent validity, and discriminant validity. Finally, Structural Equation Model (SEM) and path analysis are conducted using AMOS 22. Results: The research findings demonstrated that technological change and IT infrastructure positively and significantly impact the organisation's productivity while IT knowledge management has significant but negative impact on organizational productivity of IT companies in Malaysia. Conclusion: The research concludes that all three factors plays important role in deciding organizational producvity. Recommendations, implications, limitations and future research avenues are discussed.

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.19 no.11
• /
• pp.29-34
• /
• 2020

In this study, a sensitivity formulation was applied to analyze the dynamic response due to the effect of the excitation force for the undamped vibration of the cantilever beam. The theoretically fundamental formulations were derived considering an eigenvalue problem and its modal analysis to govern the second order algebraic differential equation in terms of the change in the modal coordinate with respect to the design parameters. A representative physical quantity pertaining to the dynamic response, that is, the rate of change in the dynamic displacement, was observed by changing the design variables, such as the cross-sectional area of the beam. The numerical results were obtained at various locations, considering the application of the external forces and observation of the dynamic displacement. When the detection position was closer to the free end of the cantilever beam, the sensitivity of the dynamic displacement was higher, as predicted through the oscillating motion of the beam. The presented findings can provide guidance to compute the dynamic sensitivity for a flexibly connected structure under dynamic excitations.

• Journal of the Korean Society of School Health
• /
• v.13 no.1
• /
• pp.117-129
• /
• 2000

The relationships between children's health behavior and variables that effect children's health behavior has been investigated in a number of previous studies. This study was conducted to examine the effects of a peer's social reinforcement on children's dental health behavior in an elementary school. The research design was a nonequivalent pre and post-test quasi-experimental design and the study subjects with one hundred and thirteen eight to nine years old children, and their mothers (57 experimental group, 56 control group) were selected as a study group. Subjects were selected by the convenience sampling method. The study was carried out in an elementary school in Namwon city, Korea, from the 26th of April to the 12th of June in 1999. Data were collected in both the pre and post-test portions. Using the "Health Belief Model", each item of the questionnaire for measurement of dental health behavior was modified and administered for the children and their mothers. The questionnaire for the measurement of dental health behavior was developed by Oh, Y.B.(1994). The Cronbach's ${\alpha}$ of the questionnaire for children were .81, and for the mother were .79. In this study, the health belief model consists of "perceived susceptibility", "perceived seriousness", "perceived barrier", "perceived salience", and "perceived benefit". The questionnaire for the children was composed of 37 items, and the questionnaire for the mother was composed of 40 items. Data were analyzed by frequency, ${\chi}^2-test$, ANOVA, Pearson's Correlation, and multiple regression analysis by a SAS program. The results of this study were summarized as follows ; 1. The first hypothesis that the experimental group would have more change in the frequency of brushing per week than that of control group was accepted(t=3.817, p=0.000). Mean tooth brushing scores in the experimental group improved significantly from pre-test to post-test, but in the control group there was no significant improvement in tooth brushing scores. 2. The second hypothesis that the experimental group would have more change in score of dental health behavior than that of control group was accepted(benefit : t=2.804, p=0.006, salience: t=2.608, p=0,010). An evaluation between the experimental group and the control group showed significant change from pre-test to post-test in health behavior scores. 3. The third hypothesis that higher scores of social reinforcement would create more change in the scores of tooth brushing frequency in the experimental group was accepted(${\beta}$=0.169, p=0.000. Multiple regression was used to examine the peer's social reinforcement scores and the relative influence of significant variables in previous ANOVA and Pearson's correlation test on children's frequency of brushing during the post-test. The results of the study indicated that the combination of social reinforcement of peers with variables pertaining to mother and householder were significantly related and effectively improved a child's tooth brushing.

• Asian Journal of Business Environment
• /
• v.7 no.3
• /
• pp.5-15
• /
• 2017

Purpose - The objective of the present study is to examine the relationship between intellectual preferences of individuals and the level of readiness for change according to Ned Herman. Research design, data and methodology - For this, Iranian Supreme Audit Court was selected as a case study in this research and it was carried out to evaluate research variables and test hypotheses using standard questionnaires of intellectual preferences and readiness for change based on the methodology. It should be remarked that only 32 managers of Audit Court were willing to participate in this research and responded to the questionnaires. Results - The outputs of the performed tests showed that although there is not a significant relationship between the individuals with intellectual preferences for class A and readiness for change them, approaching the intellectual preferences of the individuals to D region increases the readiness for change them. On the other hand, whatever individuals have intellectual preferences for branches in groups B and C, the level of preparedness for change is low. Conclusions - The results of this research have made a clear policy for the effective utilization in human resources based on their intellectual preferences model for management with organizational changes.

• Journal of Intelligence and Information Systems
• /
• v.6 no.2
• /
• pp.29-40
• /
• 2000

Process planning (selection and ordering of processes) and material selection for product manufacturing are two key things determined before taking full-scale manufacturing. Knowledge on product design. material characteristics, processes, time and cost all-together are mutually related and should be considered concurrently. Due to the complexity of problem, human experts have got only one of the feasilbe solutions with their field knowledge and experiences. We propose a hierarchical expert system framework of knowledge representation and reasoning in order to overcome the complexity. Manufacturing processes have inherently hierarchical relationships, from top level processes to bottom level operation processes. Process plan of one level is posted in process blackboard and used for lower level process planning. Process information on blackboard is also used to adjust the process plan in order to resolve the dead-end or inconsistency situation during reasoning. Decision variables for process, material, tool, time and cost are represented as object frames, and their relationships are represented as constraints and rules. Constraints are for relationship among variables such as compatibility, numerical inequality etc. Rules are for causal relationships among variables to reflect human expert\`s knowledge such as process precedence. CRSP(Constraint and Rule Satisfaction Problem) approach is adopted in order to obtain solution to satisfy both constraints and rules. The trade-off procedure gives user chances to see the impact of change of important variables such as material, cost, time and helps to determine the preferred solution. We developed the prototype system using visual C++ MFC, UNIK, and UNlK-CRSP on PC.

• 한국항공우주법학회:학술대회논문집
• /
• 2008.05a
• /
• pp.165-182
• /
• 2008

The purpose of this study is to review the changes in the aviation safety management system, how that system has evolved and what forces caused these changes to take place. Also included is an examination of the development process of the aviation safety management system in view of the new institutionalism, identifying the patterns of change. Based on the results of this study, I propose policy methods to design a desirable civil aviation safety system with a view toward raising the safety standards in the Korean civil aviation community. The major analysis variables are as follows: first, aviation accidents caused by external factors and international standards as independent variables; second, environmental changes and political processes affecting aviation safety management system as major mediating variables; and third, the aviation safety management legal system, the aviation safety management organizations and an expert participation system as dependent variables. The institutional changes and continuance of the aviation safety management system show that when specific circumstances arise, the continuance lasts depending on the path dependency, and in a certain circumstance, when immanent changing factors reach a critical point, the system suddenly changes by a punctuated equilibrium, which are all included in this study.