• Membrane and Water Treatment
• /
• v.13 no.4
• /
• pp.173-181
• /
• 2022

Polyvinylidene fluoride (PVDF) flat sheet hydrophobic membranes were prepared using 16 wt% PVDF in Dimethyl acetamide (DMAc) by phase inversion technique for desalination application using Membrane Distillation (MD). In this work, the effect of coagulation mediums such as ethanol and water as well their synergistic behavior on the fabricated PVDF membrane morphology was studied using SEM. Moreover, other characteristics required for the membrane distillation applications namely porosity, hydrophobicity and tensile strength were measured using the gravimetric method, sessile drop method and universal testing machine respectively. It was observed that the membrane morphology paradigm shifted from the finger-like structure to the sponge-like structure on increasing the ethanol concentration in coagulant. The porosity of the fabricated membrane was under the required MD range and found to be 57.3% at 16 weight % of PVDF in DMAc solvent under a pure ethanol coagulant bath. Moreover, the top surface contact angle ranges from 85° to 115° on increasing the bath concentration from CBC 0 to CBC 100 at 16 weight % of PVDF in DMAc solvent.

• Journal of Conservation Science
• /
• v.28 no.4
• /
• pp.343-351
• /
• 2012

Excavated archaeological iron objects are prevented from being corroded going through desalination which slow down being corroded. However archaeological iron objects are liable to be corroded due to the high ionization tendency even though they are stored in environment restricted from corrosion factors. Iron objects could be deteriorated more than just excavated. Therefore this study investigated about the characteristic of re-corrosion and the effect on objects. In study, archaeological iron nails in storage for 4 years after conservation treatments were tested. Optical microscopy and X-ray photography for appearance, XRD, SEM-EDS, Raman spectroscopy for chemical composition, IC for chloride ions concentration inside iron nails were used. As results, iron nails carried out conservation treatments measured a high concentration of chloride ions after the long storage period. The form of objects were not in good condition such as broken or destroyed when the high chloride ions concentration was detected. In addition, the yellow and red powdery corrosion product were detected on the boundary between corrosion products and substrates and they were identified as akaganeite which is symptom of active corrosion.

• Membrane and Water Treatment
• /
• v.7 no.4
• /
• pp.341-353
• /
• 2016

Papermaking reconstituted tobacco is an important strategy for recycling the waste tobacco residues. To indentify the influences of the inorganic components on harmful components delivery in cigarette smoke, a self-made electrodialysis stack was assembled to desalt the tobacco extract. The influences of the applied current and extract content on the removal rate of the inorganic ions were investigated. Results indicated that the applied current was a dominant impact on the desalination performance. High currents lower than the limiting current density could accelerate the desalting efficiency but cause higher energy consumption. A current of 2 A, or current density of ${\sim}11mA{\cdot}cm^{-2}$, was an optimal choice by considering both the energy consumption and desalting efficiency. A 20% tobacco extract was an appropriate content for the electrodialysis process. More than 90% of inorganic ions could be removed under the optimum condition. The preliminary result indicated that removal of inorganic components was beneficial to decrease the harmful component delivery in cigarette smoke. Naturally, ED is an environmentally friendly and high-effective technology for desalting the tobacco extract.

• Membrane and Water Treatment
• /
• v.4 no.4
• /
• pp.237-249
• /
• 2013

Ultra-pure water (UPW), a highly treated water free of colloidal material and of a conductivity less than 0.06 ${\mu}S$, is an essential component required by modern industry. One of the methods for UPW production is the electrodialysis-ion exchange (ED/IE) system, in which the electrodialysis (ED) process is used as a preliminary demineralization step. The IE step can be replaced with electrodeionization (EDI) to decrease the volume of post-regeneration lyes. In this paper, the electrodialysis process carried out to relatively low diluate conductivity was investigated and the costs of UPW production were calculated. The optimal value of desalination degree by ED in the ED/IE and ED/EDI systems was estimated. UPW unit costs for integrated ED/IE and ED/EDI systems were compared to simple ion exchange and other methods for UPW production (RO-IE, RO-EDI). The minimal UPW unit costs in ED/EDI integrated system were estimated as $0.37/$m^3$ for feed TDS 600 mg/L and $0.36/$m^3$ for feed TDS 400 mg/L at 64 $m^3/h$ capacity, which was lower than in the comparable ED/IE integrated system ($0.42-0.44/$m^3$). The presented results suggest that an ED/EDI integrated system may be economically viable.

• Laser Solutions
• /
• v.14 no.1
• /
• pp.19-24
• /
• 2011

This work reports the results for laser shock peening of duplex stainless steel (22% Chromium - 5% Nickel) using a pulsed Nd:YAG laser (wavelength = 532nm, pulse width = 8ns). for the application to high-capacity pumps for seawater desalination plants. By properly selecting the process parameters such as laser intensity of 10GW/$cm^2$, laser pulse density of 75pulse/$mm^2$, and $100{\mu}m$ thick aluminum foil as an absorbent coating layer, the surface hardness of duplex stainless steel could be enhanced by 26%, from 256HV to 323HV with little changes in surface morphology and roughness. The depth of laser shock peened layer was measured to be around 2mm. The large enhancement of surface hardness is considered to have high practical importance in minimizing abrasive and corrosive deterioration of pump parts.

• Advances in nano research
• /
• v.12 no.3
• /
• pp.253-261
• /
• 2022

Numerical modelling of an integrated Carbon NanoTube (CNT) membrane is only achievable if probable deformations and realistic alterations from a perfect CNT membrane are taken into account. Considering the possible forms of CNTs, bending is one of the most probable deformations in these high aspect ratio nanostructures. Hence, investigation of effect associated with bent CNTs are of great interest. In the present study, molecular dynamics simulation is utilized to investigate fluid flow dynamics in deformed CNT membranes, specifically when the tube cross section is not affected. Bending in armchair (5,5) CNT was simulated using Tersoff potential, prior to flow rate investigation. Also, to study effect of inclined entry of the CNT to the membrane wall, argon flow through generated inclined CNT membranes is examined. The results show significant variation in both cases, which can be interpreted as counter-intuitive, since the cross section of the CNT was not deformed in either case. The distribution of fluid-fluid and fluid-wall interaction potential is investigated to explain the anomalous behavior of the flow rate versus bending angle.

• Membrane and Water Treatment
• /
• v.1 no.1
• /
• pp.75-81
• /
• 2010

The aim of this work is to analyse and discuss the use of the Economic Evaluation and of some new "metrics" for an appropriate valuation of membrane operations in the logic of Process Intensification. In particular, the proposed approach has the goal to show how the utilized indicators can drive to the choice of the most convenient process. Although in this work the planned procedure is applied, as a case study, to the membrane-based systems for boron and arsenic removal from waters, the suggested approach can be generally applied to any other process of interest.

• Journal of Advanced Marine Engineering and Technology
• /
• v.25 no.6
• /
• pp.1250-1259
• /
• 2001

This study was experimentally performed to investigate sea water freezing behavior along parallel cooled plate with bubbly flow The experiments were carried out for a variety of parameter, such as sea water velocity, air-bubble flow rate, and cooled-plate temperature. The shape of freezing layer, freezing rate and salinity of frozen layer were observed and measured. It was found that the experimental parameters gave a great influence on the freezing rate and the salinity of the frozen layer.

• Journal of Advanced Marine Engineering and Technology
• /
• v.39 no.5
• /
• pp.548-553
• /
• 2015

The conventional ejector-diffuser system makes use of high pressure primary stream to propel the secondary stream through pure shear action for the purposes of transport or compression of fluid. It has been widely used in many industrial applications such as seawater desalination, solar refrigeration, marine engineering, etc. The present study is performed numerically to study the performance of a two-stage ejector-diffuser system. The detailed flow phenomenon of the ejector-diffuser system has been critically predicted by means of the numerical approach using compressible Reynolds averaged Navier-Stokes (RANS) equations. The axi-symmetric supersonic ejector-diffuser flow has been solved by a fully implicit finite volume scheme with a two-equation k-omega turbulence model. The numerical results are validated with existing experimental data. Detailed flow physics and their contributions on ejector performance are detected to compare both single-stage and two-stage ejectors. The performance improvement on the ejector-diffuser system is discussed in terms of the mass flux ratio and the coefficient of power.

• Membrane Journal
• /
• v.1 no.1
• /
• pp.5-12
• /
• 1991

Since the discovery of the Loeb-Sourirajan reverse osmosis membrane, thirty years have passed and many membrane technologies and new membranes for applications have been developed in the world. In the early stage of these developments Japan has not contributed much, but from the middle of 70ties Japan has started its own R&D projects starting from the desalination technology, and now various private industries and government ministries are actively engaging in R & D of membrane technologies in Japan. In Table 1 the chronological developments of important events of developments and projects relating membrane technologies inside and outside of Japan are introduced and their details will be explained. The first membrane technology applied in the Japanese industry was a electrodialysis(ED) process using ion-exchange membranes. These membranes were first developed in early 50ties and the Japanese government decided to use this method for concentration of sea-water to produce salt, which was then produced by solar evaporation. This development program started from 1960 by the Japan Monopoly Corp.(at that time). To apply ED process for sea-water concentration it was necessary to develop ion-exchange membranes having very low electric resistance to avoid energy loss due to Joule heat, and those having selectivity to permeate single valent ions only to avoid scale formation in the ED stacks. Three Japanese companies, Asahi Glass, Asahi Chemical and Tokuyama Soda, have succeeded to develop such membranes, and until 1971 all of the seven salt manufacturing companies had adopted ED for production of food salt.