• 한국군사과학기술학회지
• /
• 제15권5호
• /
• pp.550-556
• /
• 2012

In this study, a series of ballistic experiments have been performed to investigate the protection mechanism of some inert reactive cassettes against shaped charge jet. Three kinds of material were tested as a core material of the inert cassettes, i.e. one of rubber materials, a high modulus and high strength composite material used for ballistic protection and a mixture of energetic materials. Parameters such as deformation of the cassettes, occurrence time of jet distortion, leading jet length and residual penetration depth were investigated from the experiments and they were compared to each other quantitatively according to the jet incidence angles. The results show that the increment of cassette deformation caused jet distortion to occur early and jet distortion brought decrease of the length of leading jet. Then the decrease of the length of leading jet accompanied the decrease of residual penetration depth.

• Progress in Superconductivity
• /
• 제8권2호
• /
• pp.132-137
• /
• 2007

We have studied superconducting parameters of $MgB_2$ single crystals from reversible magnetization measurements with the magnetic field both parallel and perpendicular to the c-axis of the crystals. The temperature dependence of the London penetration depth, ${\lambda}_{ab}{^{-2}}(T)$, obtained from the Hao-Clem analysis on reversible magnetization, shows a clear discrepancy from single-band theories. It is also found that the anisotropies of the London penetration depth, ${\gamma}_{\lambda}$, slowly increases with temperature while the anisotropy of the upper critical field, ${\gamma}_H$, decreases with temperature. These behaviors are in sharp contrast with the behavior of superconductors with a single band. The temperature dependence of ${\lambda}_{ab}{^{-2}}$, and the opposite temperature dependences of ${\gamma}_{\lambda}\;and\;{\gamma}_H$ can be well explained with the theory of the two-band superconductivity.

• Progress in Superconductivity
• /
• 제10권2호
• /
• pp.116-122
• /
• 2009

We introduce a measurement method that enables to measure the penetration depth($\lambda$) of superconductor films by using a short-ended parallel plate sapphire resonator. Variations in the $\lambda$ of $MgB_2$ films could be measured down to the lowest temperature using a sapphire resonator with a $YBa_2Cu_3O_{7-x}$ film at the bottom. A model equation of $\lambda=\lambda_0[1-(T/T_c)^{\tau}]^{-1/2}$ for $MgB_2$ films appeared to describe the observed variations of the resonant frequency of the sapphire resonator with temperature, with $\lambda_0,\;\tau$, and $T_C$ used as the fitting parameters.

• 한국전산구조공학회논문집
• /
• 제17권4호
• /
• pp.451-458
• /
• 2004

본 연구는 동결토의 동결심도 및 매설된 파이프라인의 온도분포를 예측하기 위하여 유효열용량 개념 반영한 수치해석 모델의 개발에 초점이 맞추어져 있다. 이를 위하여 저자는 사용코드인 ANAQUS를 활용하여 파이프라인이 매설된 폐쇄형 시스템의 화강 동결토에 대하여 비정상 열전달 수치해석을 수행하였다. 제안된 수치해석 모델은 Frozen Fringe에서 간극수의 상변화 효과가 반영되었다. 제안된 수치해석 모델과 실내 실험으로부터 얻어진 결과들을 비교함으로써 유효열용량 모델의 적용성을 검증하였다.

• Nuclear Engineering and Technology
• /
• 제35권2호
• /
• pp.144-153
• /
• 2003

The object of this paper is the probabilistic failure analysis on the cladding performance of WPF(Whole Pin Furnace) test fuel pins under transient conditions, and analysis of the KALIMER fuel pin using the preceding analysis. The cumulative damage estimation and Weibull probability estimation of WPF test are performed. The probabilistic method was adapted for these analyses to determine the effective thickness thinning due to eutectic penetration depth. In the results, it is difficult to assume that a brittle layer depth made by eutectic reaction is all of the thickness reduction due to cladding thinning. About 93% cladding thinning of the eutectic penetration depth is favorable as an effective thickness of cladding. And the unreliability of the KALIMER driver fuel pin under the same WPF test condition is lower than that of the WPF pin because of the higher plenum-fuel volume ratio and lower cladding inner radius vs. thickness ratio. KALIMER fuel pin developed from conceptual design has a more stable transient performance for a failure mechanism due to fission gas buildup than the WPF pin.

• 한국건축시공학회:학술대회논문집
• /
• 한국건축시공학회 2019년도 추계 학술논문 발표대회
• /
• pp.166-167
• /
• 2019

In this study, to test the performance of concrete used as a concrete admixture as a recycling method of CGS, gypsum was mixed and the chloride ion penetration resistance test of CGS and BFS substituted concrete was conducted. As a result, it was found that without gypsum type test specimen, the CGS sustituted test specimens had lower chloride ion penetration resistance than the BFS substituted specimens. When gypsum was added, it was confirmed that the chloride ion penetration resistance was poor regardless of the type of admixture. In addition, it was confirmed that both admixtures were less resistant to chloride ion penetration than OPC, regardless of the presence of gypsum. However, considering the uneven quality variation of coal, which greatly affects the quality of CGS, further research is needed.

• Geomechanics and Engineering
• /
• 제23권6호
• /
• pp.523-533
• /
• 2020

The current study focuses on the effect of the end shape of steel pipe piles on installation effort and bearing resistance using the pressing method of installation under dense ground conditions. The effect of pile rotation on the installation effort and bearing resistance is also investigated. The model steel piles with a flat end, cone end and cutting-edge end were used in this study. The test results indicated that cone end pile with the pressing method of installation required the least installation effort (load) and showed higher ultimate resistance than flat and cutting-edge end piles. However, pressing and rotation during cutting-edge end pile installation considerably reduces the installation effort (load and torque) if pile penetration in one rotation equal to the cutting-edge depth. Inclusion of rotation during pile installation reduces the ultimate bearing resistance. However, if penetration of the cutting-edge end pile equal to the cutting-edge depth in one rotation, the reduction in ultimate resistance can be minimized. In comparing the cone and cutting-edge end piles installed with pressing and rotation, the least installation effort is observed in the cutting-edge end pile installed with penetration rate equal to the cutting-edge depth per rotation.

• Environmental Engineering Research
• /
• 제24권3호
• /
• pp.376-381
• /
• 2019

In this study, a poly(vinyl) alcohol/sodium alginate (PVA/SA) mixture was used to fabricate core-shell structured gel beads for autotrophic single-stage nitrogen removal (ASNR) using aerobic and anaerobic ammonia-oxidizing bacteria (AAOB and AnAOB, respectively). For stable ASNR process, the mechanical strength and oxygen penetration depth of the shell layer entrapping the AAOB are critical properties. The shell layer was constructed by an interfacial gelling reaction yielding thickness in the range of 2.01-3.63 mm, and a high PVA concentration of 12.5% resulted in the best mechanical strength of the shell layer. It was found that oxygen penetrated the shell layer at different depths depending on the PVA concentration, oxygen concentration in the bulk phase, and free ammonia concentration. The oxygen penetration depth was around $1,000{\mu}m$ when 8.0 mg/L dissolved oxygen was supplied from the bulk phase. This study reveals that the shell layer effectively protects the AnAOB from oxygen inhibition under the aerobic conditions because of the respiratory activity of the AAOB.

• 기술발표회
• /
• 통권2006호
• /
• pp.261-269
• /
• 2006

최근 피조콘시험은 과거 일반적으로 사용되었던 표준관입시험과 함께 연약지반의 특성을 평가하기 위해 빈번히 사용되고 있다. 본 연구에서는 하부지반의 지층상태를 파악하고 설계를 위한 연약지반 심도 결정 및 시공시 수직배수재 타설심도 결정시 그 신뢰도를 향상시키기 위해서 표준관입시험결과(N치), 선행압밀하중(pc), 수직배수재 타설시 관입에너지와 피조콘시험을 통한 콘 관입저항치($q_c$)와의 관계를 분석하였다. 대상 지역별로 일정한 표준관입저항치를 기준으로 평균 연약지반심도를 결정하여, 동일한 심도에서 피조콘관입저항치를 값을 분석한 결과 $q_c$=(1.09~1.63)N, 선행압밀하중을 고려한 결과 $q_c$=(1.21~1.98)N의 관계를 나타내었다. 또한 수직배수재 타설시 관입에너지와 피조콘시험을 통한 콘 관입저항치($q_c$)와의 관계를 분석한 결과 평균적으로 피조콘 관입저항치 10kgf/$cm^2$의 경우 수직배수재 타설 시 관입저항치는 약 65~70.0kgf/$cm^2$의 값을 나타내였다.

• 한국콘크리트학회:학술대회논문집
• /
• 한국콘크리트학회 2004년도 추계 학술발표회 제16권2호
• /
• pp.809-812
• /
• 2004

The evaluation of characteristics of concrete coated by high performance surface penetration agency was examined through various tests, i.e., compressive strength, penetration depth, water and air permeability, absorption according to various high performance surface penetration agencies and various compressive strengths of base concrete. The 4 types of high performance surface penetration agencies were used i.e., organic, inorganic, water soluble, and alcohol soluble. And 3 types of compressive strength of base concrete were used such as 21, 24 and 30 MPa. The characteristics of concrete coated high performance surface penetration agency was more improved than that of non-coated concrete, and especially, water soluble inorganic agency was most effective. And if compressive strength of base concrete was low, the improved effects would be larger.