• Fashion & Textile Research Journal
• /
• v.13 no.6
• /
• pp.990-995
• /
• 2011

This study analyzed the effects of the knit stitch type, fiber composition, and yarn thickness on the mechanical properties of knitted fabric. The results were as follows: The course density was the highest in the case of the rib stitch. On the other hand, the wale density was the highest in the case of the float stitch. The thickness was the highest in the case of the rib stitch. The same results were obtained even for different fiber compositions and yarn thicknesses considered in this study. The burst strength of wool knit fabric was higher than that of A/W knit fabric. The stiffness was the lowest in the case of the plain stitch. The same results were obtained even for different fiber compositions and yarn thicknesses. The pilling properties were excellent for all knit stitches, fiber composition, and yarn thicknesses as pilling degree : 5. The air permeability decreased in the following order : rib > plain > float stitch. The same results were obtained even for different fiber compositions and yarn thicknesses. The heat retention rate decreased in the following order : rib > float > plain stitch. The same results were obtained even for different fiber compositions and yarn thicknesses.

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.15 no.2
• /
• pp.31-37
• /
• 2016

In the steam system, a stream trap valve discharges a condensate and a non-condensable gas. It also prevents stream from being leaked. The free float stream trap valve is a mechanical type of stream trap. The valve is opened when a hallow ball is floated due to the density of the condensate through the condensate flows into the valve. On the other hand, when the flow of the condensate is completed, the valve is closed as the float subsides due to the weight of the structure and the stream is blocked. In addition, the bimetal lifts the hallow ball, which discharges the non-condensable gas. In this study, the performance of the properties of the free float stream trap valve, the method of support for three points, and the orifice design are researched. Moreover, the condensate discharge capacity of the free float stream trap valve is calculated from the experiment.

• Journal of the Korea Fashion and Costume Design Association
• /
• v.24 no.2
• /
• pp.1-10
• /
• 2022

The purpose of this study is to analyze the structural properties of 100% wool fabrics knitted with various stitch types and to evaluate dimensional stability from shrinkage in wet cleaning and drying. Materials were weft-knitted from twenty-four different stitches with 7 gauge using a computerized flatbed knitting machine. Weight, thickness, density, and length were measured. A domestic washing machine and a tumble dryer were used for the shrinkage test. The results are as follows: Knitted fabrics were divided into 3 groups based on weight per unit area. Porous knits show light weight whilst milano, pintuck, rib stitches belong to the heaviest group. A positive correlation between weight and thickness was found and the same result was obtained for wale density and weight. Dimensional shrinkage of knitted fabrics was increased during repetitive wet cleaning and drying regardless of knit stitches. Especially, fabrics knitted with float, tuck, cable, and links & links stitches samples were contracted more than 15% in the first treatment whereas 2x1 rib stitch showed 1% shrinkage rate. Fisherman and milano stitches contracted in both course and wale direction with similar shrinkage rates. However, porous knits with float and tuck stitches shrank in course direction by 20% as well as cable samples contracted from 5% to 20% after repeated washing and drying. On the other hand, 30% and 15% contraction of wale direction occurred in orderly float and links & links stitches, respectively. Machine dried knits have a higher shrinkage rate than air-dried knits, but the drying method did not affect to the direction of contraction. In conclusion, variations of knit, tuck, and float stitches affect knit construction and dimensional stability from shrinkage in wet cleaning and drying of wool knitted fabrics.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.30 no.10 s.253
• /
• pp.982-986
• /
• 2006

It is well known that the surface tension forces can make a particle denser than water float when the size of the particle is of the order of 1 mm. This is deeply related to the basic mechanism enabling small insects to wander around on the pond surface and also to a newly emerging technology of self-assembly using capillary forces. For the quantitative understanding of this effect, we experimentally study the maximum density of a cylinder that can float on water and how fast the cylinder sinks when the density exceeds the maximum value. We compare our experimental results with the theoretical prediction and find good agreement between them.

• Journal of Environmental Science International
• /
• v.27 no.9
• /
• pp.797-802
• /
• 2018

Information about the density of fish eggs is important to understand the vertical distribution of eggs and survival in early stage, in particular change in egg density is one of major issue in fisheries. This paper describes a practical application of an experimental system for measurement of the fish egg density under laboratory conditions. The device can control the temperature range in each water column, and make different densities at each layer. The density of olive flounder (Paralichthys olivaceus) eggs have ranged from 1,018.49 to $1,020.93kg/m^3$ and were aggregated around the density of $1,020kg/m^3$. The results show that the device is applicable for measuring the fish egg density under laboratory conditions.

• Journal of the Korean Ceramic Society
• /
• v.25 no.3
• /
• pp.237-242
• /
• 1988

Ion exchange behavior of glasses was investigated in this study. The used glasses were Soda-limesilica glasses that was produced by float process. In order to analyse effects of ion exchange, some properties were measured; $K^+$ ion penetration depth, compressive stress, compression layer thickness, amount of $K^+$ ion exchange and density, in case of 43$0^{\circ}C$-8h and 45$0^{\circ}C$-6h, and activation energy is 17.0kcal/mole. Further it can be seen that excessive heat treatment brings about stress relaxation.

• KOREAN JOURNAL OF CROP SCIENCE
• /
• v.37 no.2
• /
• pp.134-140
• /
• 1992

Carrot(Daucus carota L.) seeds (CV Danver 126) were primed and then separated by density differences to improve both the percentage and time of radicle emergence. Seeds for priming were soaked in aerated distilled water for 2 days (water imbibed), 25% solution of polyethylene glycol(PEG) 6000 for 6 or 10 days, salt solution of 0.2M KNO$_3$＋0.1M $K_2$HPO$_4$ for 6 or 10 days, or mixed with Agro-Lig with 90% moisture content for 6 days and 70% moisture content for 6 or 10 days (SMP) at 2$0^{\circ}C$, respectively. The greatest embryo growth and the highest radicle emergence were observed from the seeds treated SMP with 90% moisture content for 6 days among the primed treatments. After the SMP treatment, the seeds were separated into density classes with a float-sink procedure using aqueous solution of Maltrin 600 with 0.02/cm$^3$ density increments. The lower density classes of the carrot seeds, the more embryo growth, the higher and the faster rates of radicle emergence were exhibited in order from 1.06 to 1.14 density classes of the carrot seeds treated SMP.

• Journal of Welding and Joining
• /
• v.19 no.5
• /
• pp.526-533
• /
• 2001

Induction heating of float metal products has an increasing importance in many applications, because it generates the heat within workpiece itself and provides high power densities and productivity. In this study, the induction heating of a steel plate to simulate the line heating is investigated by means of the Finite Element Analysis of the magnetic field and temperature distribution. A numerical model is used to calculate temperature distribution within the steel plate during the induction heating with a specially designed inductor. The effects of materital properties depending on the temperature and magnetic field are taken into consideration in an iterative manner. The simulation results show good magnetic field with experimental data and provide good understanding of the process. Since the numerical model demonstrates to be suitable for analysis of induction heating process, the effects of air gap and frequency on magnetic-flux and power-density distribution are also investigated. It is revealed that these process parameters have an important roles on the electro-magnetic field and power-density distribution governing the temperature distribution of the plate.

• Korean Journal of Fisheries and Aquatic Sciences
• /
• v.51 no.3
• /
• pp.332-337
• /
• 2018

The Pacific cod Gadus macrocepahlus, lays demersal eggs and the hatching larvae rise toward the surface layer of the ocean to feed. The change in the specific gravity of eggs and larvae was investigated to examine their vertical distribution and movement in the water column. The specific gravities of fertilized eggs and various size classes of larvae were measured using a density gradient apparatus. In total, the instantaneous specific gravity of 146 eggs and 225 larvae were measured. To prevent any disturbance in the gradient water column due to larval movement, 0.004% MS222 was used for anesthesia. Due to their high specific gravity, eggs spawned were deposited over the sea-bed of the spawning ground. The specific gravity of hatching larvae decreased abruptly. However, Pacific cod larvae still had a comparatively high specific gravity at hatching ($1.03655{\pm}0.00146g/cm3$, n=4, mean SL=3.62 mm) and their specific gravities tended to decrease as they grew. The specific gravity stabilized 6 days after hatching ($1.02590{\pm}0.00212g/cm3$, n=15, mean SL=4.67 mm) and the cod larvae were eventually able to float in the water column.

• Macromolecular Research
• /
• v.12 no.2
• /
• pp.189-194
• /
• 2004

When water is evaporated quickly from a water-based colloidal suspension, colloidal particles protrude from the water surface, distorting it and generating lateral capillary forces between the colloidal particles. The protruded colloidal particles are then assembled into ordered colloidal crystalline domains that float on the water surface on account of their having a lower effective density than water. These colloidal crystal domains then assemble together by lateral capillary force and convective flow; the generated colloidal crystal has grain boundaries. The single domain size of the colloidal crystal could be controlled, to some extent, by changing the rate of water evaporation, but it seems very difficult to fabricate a single crystal over a large area of the water's surface without reorienting each colloidal crystal domain. To reorient such colloidal crystal domains, a glass plate was dipped into the colloidal suspension at a tilted angle because the meniscus (airwaterglass plate interface) is pinned and thinned by further water evaporation. The thinning meniscus generated a shear force and reoriented the colloidal crystalline domains into a single domain.