• 한국강구조학회 논문집
• /
• 제9권3호통권32호
• /
• pp.401-419
• /
• 1997

탄소성 대변형에서의 손상의 운동학을 연속체 역학적 구도 안에서 유효 응력의 개념을 통하여 4차 유효 손상 텐사를 이용하여 소개하였다. 손상 변형의 운동학적인 기술의 부재로 인하여 소변형 문제에서는 고체의 손상의 특성을 기술하기 위해서는 다음의 두 가지 가정 (변형률 등가의 가정 또는 에너지 등가의 가정)중의 하나가 일반적으로 채택되어진다. 본 연구에서 제안된 방법은 대변형에 적용될 수 있는 손상 거동의 운동학적인 일반화된 방법을 제공한다. 이 방법은 소 변형률에 국한되는 변형률 등가의 가정이나 에너지 등가의 가정 방식이 아닌 변형장의 운동학을 직접 고려하여 손상 거동의 운동학을 2차 손상 텐사의 함수인 4차 유효 손상 텐사를 이용하여 탄성 및 소성 영역에서 표현하였다.

• 대한금속재료학회지
• /
• 제48권1호
• /
• pp.85-89
• /
• 2010

The plastic deformation behavior of magnesium alloy is affected simultaneously by deformation temperature and strain rate under warm and/or hot working conditions. The soundness of deformation of AZ31-xCa (x=0. 0.7, 2.0 wt.%) extrudes during compression was strongly affected by processing variables including deformation temperature, strain rate. compression-loading direction, which was related to the activation of available deformation systems. The deformation behavior of AZ31-xCa extrudes was also affected by Ca content, which was related to the change of the sort and fraction of second phase. The complex effects of deformation temperature and strain rate on the deformation behavior of AZ31-xCa extrudes during compression under various conditions could be successfully described by Zener-Hollomon parameter.

• Structural Monitoring and Maintenance
• /
• 제7권1호
• /
• pp.1-12
• /
• 2020

Railway tracks are the direct supporting structures of the trains, which are vulnerable to produce large deformation under the temperature stress or subgrade settlement. The health status of track is critical, and the track should be routinely monitored to improve safety, lower the risk of excess deformation and provide reliable maintenance strategy. In this paper, the distributed optical fiber sensor was proposed to monitor the continuous deformation of the track. In order to validate the feasibility of the monitoring method, two deformation monitoring tests on one steel rail model in laboratory and on one real railway tack in outdoor were conducted respectively. In the model test, the working conditions of simply supported beam and continuous beam in the rail model under several concentrated loads were set to simulate different stress conditions of the real rail, respectively. In order to evaluate the monitoring accuracy, one distributed optical fiber sensor and one fiber Bragg grating (FBG) sensor were installed on the lower surface of the rail model, the strain measured by FBG sensor and the strain calculated from FEA were taken as measurement references. The model test results show that the strain measured by distributed optical fiber sensor has a good agreement with those measured by FBG sensor and FEA. In the outdoor test, the real track suffered from displacement and temperature loads. The distributed optical fiber sensor installed on the rail can monitor the corresponding strain and temperature with a good accuracy.

• 한국항해학회지
• /
• 제21권3호
• /
• pp.49-54
• /
• 1997

It is very important to measure and monitor hull stress which is caused by a buoyant force and a weight of cargo for safety of ship. However, an exact measurement of hul stress, using the traditional strain gage which is made of metal or semiconductor, is very difficult, because a ship would be exposed by the severe temperature environment of $-20 ^{\circ}C$ to $80 ^{\circ}C$. This paper propose a new concept strain gage which can improve accuracy and compensage effectively affects due to temperature. The strain gage is consists of two parts. One is the Hull Deformation Amplifier which introuce several lever and link system, and another is a transducer converting distance into voltage signal. The HDA measure the amount of deformation and amplify it. And a lever and link system of the HDA is introduced for compensating temperature deformation by installing in perpendicular direction without stress. This paper also reports on the results of the experiments to verify linearity of the strain gage.

• 소성∙가공
• /
• 제17권1호
• /
• pp.46-51
• /
• 2008

Polycrystalline materials such as steels(BCC) and aluminum alloys(FCC) show the strain hardening and the strain rate hardening during the plastic deformation. The strain hardening is induced by deformation resistance of dislocation glide on some crystallographic systems and increase of the dislocation density on grain boundaries or inner grain. However, the phenomenon of the strain rate hardening is not demonstrated distinctly in the rage of $10^{-2}$ to $10^2/sec$ strain rate. In this paper, tensile tests for various strain rates are performed in the rage of $10^{-2}$ to $10^2/sec$ then, specimens are extracted on the same strain position to investigate the microscopic behavior of deformed materials. The extracted specimens are investigated by using the electron backscattered diffraction(EBSD) and transmission electron microscopy(TEM) results which show the effect of texture orientation, grain size and dislocation behavior on the strain rate hardening.

• 한국분말야금학회:학술대회논문집
• /
• 한국분말야금학회 2006년도 Extended Abstracts of 2006 POWDER METALLURGY World Congress Part2
• /
• pp.1251-1252
• /
• 2006

In order to investigate 95% retained critical current of Bi-2223/Ag tapes under various stress-strain conditions, load cell attached tension and bending apparatus was used. The critical current of stress-strained tape was degraded below 95% retained critical current when tension and bending was simultaneously applied together. But only one of this tension or bending did not degrade the tape below 95% retained critical current. Deformation temperature was important to maintain the 95% retained Ic of Bi-2223/Ag tapes after bending or tension deformation because mechanical strength of tapes can be changed drastically between room temperature and 77 K.

• 한국융합학회논문지
• /
• 제5권1호
• /
• pp.23-27
• /
• 2014

본 연구에서는 소형 인장 시험편에 편심된 집중하중을 가하였을 때, 크랙 주변에서의 구멍의 존재유무, 개수 및 위치에 따른 전파 거동에 대하여 규명하였다. 시뮬레이션 해석을 통하여 시험편에서 발생하는 Strain energy와 변형량, 응력에 대해 알 수 있었다. 그리고 이들 Strain energy와 변형량을 바탕으로 응력확대계수를 구하였으며, 본 연구결과를 이용하면 구조물 내에 결함이나 구멍 등이 있을 때 그 파괴 가능성을 검증할 수 있다고 사료된다.

• 한국의류산업학회지
• /
• 제18권6호
• /
• pp.733-745
• /
• 2016

This paper provides a review of wearable textile strain sensors that can measure the deformation of the body surface according to the movements of the wearer. In previous studies, the requirements of textile strain sensors, materials and fabrication methods, as well as the principle of the strain sensing according to sensor structures were understood; furthermore, the factors that affect the sensing performance were critically reviewed and application studies were examined. Textile strain sensors should be able to show piezoresistive effects with consistent resistance-extension in response to the extensional deformations that are repeated when they are worn. Textile strain sensors with piezoresistivity are typically made using conductive yarn knit structures or carbon-based fillers or conducting polymer filler composite materials. For the accuracy and reliability of textile strain sensors, fabrication technologies that would minimize deformation hysteresis should be developed and processes to complement and analyze sensing results based on accurate understanding of the sensors' resistance-strain behavior are necessary. Since light-weighted, flexible, and highly elastic textile strain sensors can be worn by users without any inconvenience so that to enable the users to continuously collect data related to body movements, textile strain sensors are expected to become the core of human interface technologies with a wide range of applications in diverse areas.

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 2000년도 추계학술대회 논문집
• /
• pp.29-32
• /
• 2000

The static and metadynamic recrystallization of non-heat treated medium carbon steel(Fe - 0.45wt.$\%C\;-\;0.6wt.\%Si\;-\;1.2wt.\%Mn\;-\;-0.12wt.\%Cr \;-\;0.1wt.\%V \;-\;0.017wt\%$.Ti) were studied by the torsion test in the strain rate range of 0.05 - 5 $sec^{-1}$, and in the temperature range of $900\;-\;1100\;^{\circ}C$. Interrupted deformation was performed with 2 pass deformation in the pass strain range of $0.25 {\varepsilon}_p(peak strain)\;and\;{\varepsilon}_p$, and in the interpass time range or 0.5 - 100 sec. The dependence or pass strain(${\varepsilon}_i$), strain rate( $\dot{\varepsilon}$ ), temperature(T), and interpass time($t_i$) on static recrystallization (SRX) and metadynamic recrystallization (MDRX) were predicted from the modified Avrami's equations respectively. Comparison of the softening kinetics between SRX and MDRX was indicated that the rate of MDRX was more rapid than that of SRX under the same deformation variables.

• Ocean Systems Engineering
• /
• 제4권4호
• /
• pp.309-325
• /
• 2014

Geotextile tubes are basically a huge sack filled with sand or dredged soil. Geotextile tubes are made of permeable woven or non-woven synthetic fibers (i.e., polyester or PET and polypropylene or PP). The geotextile tubes' performances in strength, dewatering, retaining solid particles and stacked stability have been studied extensively in the past. However, only little research has been done in the observation of the deformation behavior of geotextile tubes. In this paper, a large-scale apparatus for geotextile tube experiment is introduced. The apparatus is equipped with a slurry mixing station, pumping and delivery station, an observation station and a data station. For this study the large-scale apparatus was utilized in the studies regarding the stresses on the geotextile and the deformation behavior of the geotextile tube. Model tests were conducted using a custom-made woven geotextile tubes. Load cells placed at the inner belly of the geotextile tube to monitor the total soil pressure. Strain gauges were also placed on the outer skin of the tube to measure the geotextile strain. The pressure and strain sensors are attached to a data logger that sends the collected data to a desktop computer. The experiment results showed that the maximum geotextile strain occurs at the sides of the tube and the soil pressure distribution varies at each geotextile tube section.