• 대한기계학회논문집A
• /
• 제20권12호
• /
• pp.3847-3855
• /
• 1996

In order to study the relationship between static and cynamic behaviors of silion caride, both quasi-static indentaiton and impact experiments of spherical particle have been conducted. The difference inmaterial behavior when using the two mehtods suggests a loading rate difference in the damate pattrern and fracture strength of silicon carbide. This investigation showed some difference in damage pattern according to particla property, especially inthe case of particle impact. There was no differences in deformation behaviors according to the loading rate when the crater profiles were compared with each other at the same contact radius. From the result of residual strength evaluation, it was found that the strength degradation began at the initiation of ring crack and its behavior was colsely related to morphologies of the damage developed which was also dependent upon the extent of deformation atthe loaidng point. In the case of static indentation, there didnot exist the particle property effects onthe strength degradation behavior.

• 한국수자원학회논문집
• /
• 제39권1호
• /
• pp.69-77
• /
• 2006

포항시에 위치한 송도해안은 오랜 기간 동안 여러 가지 원인에 의하여 해안침식이 진행되었다. 송도해안의 해안침식 문제와 관련하여 논쟁의 이슈로 되어 있는 문제 중 하나는, 해안침식에 대한 주변 해안구조물의 영향 범위이다. 본 연구에서는, 이를 검토하기 위하여 송도해안의 침식특성과 관련된 기존자료 및 항공사진자료 등을 통하여 재분석하였다. 특히, 주변지역의 인위적인 해안개발 상황을 토대로 실험안을 구성한 후, 3차원 지형변동모델을 이용하여 송도해안의 해빈변형상황을 검토하였으며, 아울러, 이러한 다방면의 해석을 통해 얻어진 검토결과들을 토대로 대상해안의 침식이력특성을 파악하고자 하였다.

• 대한조선학회논문집
• /
• 제30권3호
• /
• pp.100-115
• /
• 1993

본 논문에서는 구조전체의 최종붕괴강도에 대한 국부 구성부재의 과도인장변형효과를 고려하기 위하여 기존의 이상화구조요소들, 즉 이상화 보-기동요소, 이상화 판요소 및 이상화 보강판요소의 적용범위를 확장하며, 이를 위해 간이 역학적모델을 제시한다. Leander급 Frigate함의 1/3 축척 선각구조모형에 대해 Dow가 수행한 최종 종강도실험결과와 본 해석결과를 비교한 결과, 압축에 의한 구조부재의 파손 뿐만아니라 과도인장변형에 의한 파손도 구조전체적인 붕괴거동, 특히 붕괴후 거동에 크게 영향을 미침을 알 수 있었다.

• 한국지반공학회논문집
• /
• 제19권6호
• /
• pp.189-206
• /
• 2003

터널시공 중, 터널자체의 안정성 확보와 주변지반 및 인접 구조물의 안정성 확보를 위한 체계화된 계측관리는 매우 중요한 사항이라고 할 수 있는데, 지반조건이 불리한 도심지 터널공사나 지반조건이 급격하고 빈번하게 변화하는 경우에 있어서는 그 중요성이 더욱 증대되는 것이 사실이다. 최근 오스트리아에서는, 임의 시점에 대한 절대변위를 계측하고 분석하는 기존의 방법 대신, Geodetic을 이용한 각 시공단계별 상대변위의 계측 및 분석방법이 널리 증가하고 있는데, 이를 통해 지반조건의 급격한 변화 예측 및 이에 상응하는 굴착방법과 지보방식의 변경등이 용이해지고 있다. 한편, 지반의 변위는 막장 굴착이 시공되기 이전부터 발행하기 시작하므로 막장 전방의 응력상태는 향후 변위 진행과정에 있어 매우 중요한 요소라 할 수 있다. 즉, 막장 전방의 강성이나 응력상태는 굴착 후의 장기적인 터널안정성 및 인접 구조물의 안정성 확보와 관련된 주요 변수라 할 수 있다. 본 논문에서는 이와 관련된 다양한 조건에 대한 3차원 변위해석을 실시하였으며, 그 결과를 통해 터널 굴착시의 수직변위 및 벡터회전, 막장면 변위 등의 변화를 살펴보았다.

• Journal of Pharmaceutical Investigation
• /
• 제40권4호
• /
• pp.237-244
• /
• 2010

This study investigated basic material properties and compressibility of commonly used pharmaceutical excipients. Five classes of excipients are selected including starch, lactose, calcium phosphate, microcrystalline cellulose (MCC), and povidone. The compressibility was evaluated using compression parameters derived from Heckel and Kawakita equation. The Heckel plot for lactose and dicalcium phosphate showed almost linear relationship. However, for MCC and povidone, curves in the initial phase of compression were observed followed by linear regions. The initial curve was considered as particle rearrangement and fragmentation and then plastic deformation at the later stages of the compression cycle. The Kawakita equation showed MCC exhibited higher compressibility, followed by povidone, lactose, and calcium phosphate. MCC undergoes significant plastic deformation during compression bringing an extremely large surface area into close contact and facilitating hydrogen bond formation between the plastically deformed, adjacent cellulose particles. Lactose compacts are consolidated by both plastic deformation and fragmentation, but to a larger extent by fragmentation. Calcium phosphate has poor binding properties because of its brittle nature. When formulating tablets, selection of suitable pharmaceutical excipients is very important and they need to have good compression properties with decent powder flowability. Material properties tested in this study might give a good guide how to select excipients for tablet formulations and help the formulation scientists design the optimum ones.

• Computers and Concrete
• /
• 제26권6호
• /
• pp.547-563
• /
• 2020

In this paper, the influence of axial compression ratio on the mechanical properties of new type joints of side span of rectangular concrete-filled steel tubular column-H-type steel beam is studied. Two new types of side-span joints of rectangular concrete-filled steel tubular column-H-type steel beam are designed and quasi-static tests of five new type joints with 1:2 scale reduction ratios are performed. The axial compression ratio of joint JD1 is 0.3, 0.4 and 0.5, and the axial compression ratio of joint JD2 is 0.3 and 0.5. In the joint test, different axial forces were applied to the top of the column according to different axial compression ratios, and low-cyclic reciprocating load was applied on the beam. The stress and strain distribution, beam and column deformation, limit state, failure process, failure mechanism, stiffness degradation, ductile deformation and energy dissipation capacity of the joint were measured and analyzed. The results show that: with the increase of axial compression ratio, the ultimate bearing capacity of the joint decreases slightly, the plastic deformation decreases, and the stiffness and ductility decrease. According to the energy dissipation curve of the specimen, the equivalent damping coefficient also increases with the increase of axial compression ratio in a certain range, indicating that the increase of axial compression ratio can improve the seismic performance of the joint to a certain extent. The finite element method is used to simulate the joint test, and the test results are in good agreement with the simulation results.

• 소성∙가공
• /
• 제7권3호
• /
• pp.282-290
• /
• 1998

In bulk metal forming processes prediction of tool life is very important for saving production cost and achieving good material properties. Generally the service life of tools in metal forming process is limited to a large extent by wear, fracture and plastic deformation of tools. In case of hot and warm forging processes tool life depends on wear over 70%. In this study finite element analyses are con-ducted to warm and hot forging by adopting suggested wear model. By comparison of simulation and eal profile of die suggested wear model. By comparison of simulation and real profile of die suggested model is verified.

• 소성∙가공
• /
• 제7권3호
• /
• pp.274-281
• /
• 1998

The service life of tools in metal forming process is to a large extent limited by wear, fatigue fracture and plastic deformation. In elevated temperature forming processes wear is the predominant factor for tool operating life. To predict tool life by wear Achard's model is generally applied. Usually hardness of die is considered to be a function of temperature. But hardness of die is a function of not only tem-perature but also operating time of die. To consider softening of die by repeated operation it is necessary to express hardness of die by a function of a function of temperature and time. By experiment of reheating of die softening curve was obtained and applied to suggest modified Archard's Model in which hardness is a function of main tempering curve.

• 한국해양공학회지
• /
• 제17권5호
• /
• pp.48-56
• /
• 2003

This paper has developed an efficient nonlinear finite element method that covers both initial deformations and initial stresses of general distribution in calculating the ultimate strength of ring-stiffened cylinders. The developed method and two widely-used commercial codes (NASTRAN and ABAQUS) were simultaneously applied to the same analysis model within the extent of those commercial codes' coverage to check the validity of the present method. After the validity check, it was used for parametric studies for more general cases of initial stress distribution, which produced some useful information about the imperfection sensitivity of the ultimate strength of ring-stiffened cylinders.

• 비파괴검사학회지
• /
• 제28권6호
• /
• pp.477-482
• /
• 2008

The influence of dislocation substructure of metallic materials on ultrasonic velocity has been experimentally investigated. The test materials of pure Cu, brass (Cu-35Zn), 2.25Cr-1Mo steel, and AISI 316 with different stacking fault energy (SFE) are plastically deformed in order to generate dislocation substructures. The longitudinal wave velocit $(C_L)$ decreases as a function of tensile strain in each material. The $C_L$ of Cu-35Zn and AISI 316 decreases monotonously with tensile strain, but $C_L$ of Cu and 2.25Cr-1Mo steel shows plateau phenomena due to the stable dislocation substructure. The variation of ultrasonic velocity with the extent of dislocation damping and dislocation substructures is discussed.