• 한국표면공학회지
• /
• 제43권6호
• /
• pp.283-288
• /
• 2010

Ni-$TiO_2$ nano composite coatings were fabricated using pulse current electrodeposition technique at 100 Hz pulse frequency with a constant 50% pulse duty cycles and reference was taken with respect to the direct current (dc) electrodeposition. The properties of the composite coatings were investigated by using SEM, XRD, Wear test and Vicker's microhardness test. Pulse electrodeposited composite has exhibited enhancement of (111), (220), and (311) diffraction lines with an attenuation of (200) line. The results demonstrated that the microhardness of composite coatings under pulse condition was significantly improved than that of pure nickel coating as well as dc electrodeposited Ni-$TiO_2$ composite coatings. Wear tracks have shown the less plastic deformation in pulse plated composite. Coefficient of friction was also found to be lower in pulse plated composite coatings as compared to dc plated composite coatings.

• 한국정밀공학회지
• /
• 제17권3호
• /
• pp.174-183
• /
• 2000

Non-Parallelism the axial direction occurs during grinding process of long slender shafts. The reason for the axial error is due to elastic deformation of the components, accumulation phenomenon of the grinding and wheel wear during the grinding process. The accumulation phenomenon, the size generation mechanism and the wheel wear process during traverse grinding result in complicated process at each step on the wheel surface. The grinding system stiffness obtained from the stiffness of the center on the tailstock and the workpiece varing according to the relative position of the wheel and the workpiece. Further more, the value of wheel wear increases as the grinding process advances. The above mentioned issues make the shape generation process during traverse grinding quite complicated. This research analyzes the shape generation process in the direction of the work spindle. First, the formulation of the grinding system stiffness was conducted and the simulation analysis method of the traverse grinding was established. Also, a measuring system for assessing the dimensinal accuracy of the workpiece has been developed.

• Tribology and Lubricants
• /
• 제11권5호
• /
• pp.31-39
• /
• 1995

The surface integrity of a machined surface is an important factor that dictates several performance characteristics of a metal part. In this paper, the surface integrity aspects are presented specifically with respect to the tribological properties of steel. Test specimens were prepared under varying conditions to induce different levels of surface deformation and hardness. Sliding and rolling experiments were performed to assess the friction and wear characteristics of these specimens using a pinon-disk type tribotester and a plate-on-ball type set-up. It is reaffirmed that heat treated steels possess superior sliding and rolling fatigue resistance than raw steel. However, for the case of raw steels machined under varying conditions, the harder specimen resulted in higher wear. This result is attributed to the presence of surface cracks that were induced during machining. The results of such findings will aid in the optimization of surface preparation process for tribological applications of steel.

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 1998년도 금형가공 심포지엄
• /
• pp.54-59
• /
• 1998

In this study, two kinds of life prediction method for hot forming die are developed . One is empirical method requiring some experiment that evaluate thermal softening of die material accoring to operating conditions. The other is analyticl method that calcuate wear quantity of die occuring during the forming process. Wear is a predominant factor as well as plastic deformation and heat checking . And, these methods are applied to prodict tool life real die producting part for automobile. Thus , the applicability and the accuracy of the presented methods are investigated. Using the verified life prediction method above , optimal blocker die design minimizing the finisher die is done.

• 한국자동차공학회논문집
• /
• 제10권2호
• /
• pp.117-122
• /
• 2002

This study assesses the wear process of particle impingement erosion which is a major source of erosion among fluid power components. First, Bitter's theory was modified to simplify engineering calculations. Second, actual experiments were conducted to validate the modified equation. And the effect of concentration and size distribution of impinging particles was tested. Little deviation from the prediction of the modified equation was observed. To develop complete analytical approach to the erosion mechanism, further experimental data are required to establish a correlation with other engineering parameters.

• 한국분말야금학회:학술대회논문집
• /
• 한국분말야금학회 2006년도 Extended Abstracts of 2006 POWDER METALLURGY World Congress Part2
• /
• pp.841-843
• /
• 2006

In high-performance cold work applications, tool failure depends on the predominating loading conditions. Typical failure mechanisms are a combination of abrasive wear, adhesive wear, plastic deformation, cracking and edge crumbling. In this paper we demonstrate how the microstructure of tool steels can be positively influenced by modifying the alloying system and the production route to meet the demands of the different loading situations which occur during operation. The investigation was focused on ductility, fatigue strength and wear resistance. Theoretical considerations were confirmed by practical tests.

• 대한안전경영과학회지
• /
• 제4권2호
• /
• pp.223-235
• /
• 2002

This paper presents some indirect physical evidences indicating that reduced friction occurs in an economical cryogenic machining process, in which LN2 is applied selectively in well-controlled jets to the localized cutting zone. These evidences include cutting force components, tool wear rate and chip morphology. LN2 reduced the tool wear rate to a great extent and elongated the tool life up to four times compared to emulsion cooling. The friction reduction was further reflected in larger shear angle and less secondary deformation in the chip microstructures. This study also found that the effectiveness of LN2 lubrication depends on the approach how LN2 is applied.

• 한국안전학회지
• /
• 제18권4호
• /
• pp.16-22
• /
• 2003

Generally the rupture of steam generator tubes proceeds from significant plastic deformation before failure. In this study, the burst pressures of damaged steam generator tubes were calculated from the plastic instability analysis with the finite element method. Two wear types, flat and circumferential types were considered. An equation for the burst pressure was proposed by using the strength reduction factor and the Svensson equation. The analysis results were compared with the experiment data from published references and they showed a good agreement with the experiment data.

• 한국윤활학회:학술대회논문집
• /
• 한국윤활학회 2001년도 제33회 춘계학술대회 개최
• /
• pp.15-21
• /
• 2001

This study assesses the wear process of particle impingement erosion which is a major source of erosion among fluid power components. First, Bitter's theory was modified to simplify engineering calculations. Second, actual experiments were conducted to validate the modified equation. And the effect of concentration and size distribution of impinging particles was tested. Little deviation from the prediction of the modified equation was observed. To develop an analytical approach to the erosion mechanism, further experimental data are required to establish a correlation with other engineering parameters.

• 한국정밀공학회지
• /
• 제8권1호
• /
• pp.74-83
• /
• 1991

A study on the Correlation of Orthogonal Cutting Parameter (Cutting speed, Depth of cut, Feed Rate) and Acoustic Emission Signal. It is well known that acoustic emission (AE) is the emission of elastic wave resulting from the deformation and fracture of materials. This study estabished correlation of orthogonal cutting parameter and AE signal, and researched into in-process monitoring of tool wear and failure. The results are as follow; 1. AE RMS was under the influence of cutting speed but hardly influenced by depth of cut and feed rate. 2. AE RMS was under the influence of flank wear. 3. AE count rate increased by increased cutting speed. 4. AE RMS value was rapidly increased in 130 m flank wear.