• 한국건축시공학회:학술대회논문집
• /
• 한국건축시공학회 2013년도 추계 학술논문 발표대회
• /
• pp.34-35
• /
• 2013

In this study, the ultra high strength concrete which have 80, 130, 180MPa took the heat from 20℃ to 700℃ and the 0, 20% stress in normal condition's to evaluate stress-strain, residual compressive strength and thermal expansion deformation were evaluated. The heating speed of specimen was 0.77℃/min 20~50℃, 50℃ before the target temperature, and the other interval's heating speed was 1℃/min. As a result, the stress-strain curve of non-load specimen showed the liner behavior at high temperature when the specimen's strength increased more. If ultra high strength concrete got loads, its compressive strength tended to decrease different from the normal strength concrete. The thermal expansion deformation was expanded from a vitrification of quartz over 500℃. however, over the 600℃, it was shrinked because of the dehydration of the combined water.

• 한국구조물진단유지관리공학회 논문집
• /
• 제2권2호
• /
• pp.209-217
• /
• 1998

Compared to normal-strength concrete, high-strength concrete has the lower lateral expansion capacity caused by the higher elastic modulus and the lower internal crack characteristic. Therefore, the effect of the lateral confining action of hoops appears slowly. Nevertheless, it has been reported that the strength and deformation capacity of high-strength concrete is improved by well-distributed hoops. Due to that argument, this investigation has been compared and analyzed by the experimental works on the deformation capacity and the confinement mechanism of high-strength concrete shear wall of the high-rise building reinforced by rectangular steel tubes and rectangular hoops at both edges. It is suggested that, using high-strength concrete($500kgf/cm^2$, $700kgf/cm^2$), hoops should be replaced with rectangular steel tubes in order to prevent closely spaced hoops at the edge of the shear wall.

• 한국공간구조학회논문집
• /
• 제6권3호
• /
• pp.69-76
• /
• 2006

콘크리트 충전 강관(Concrete Filled Steel Tube : CFT) 기둥은 내력 및 변형능력 등 구조적 성능이 뛰어남에도 불구하고 강관내부에 충전한 콘크리트의 재료분리저항성 및 유동성이 확보되는 고품질의 콘크리트가 요구되며, 또한, 다이어프램 하부의 충전 확인이 어렵다는 문제점을 안고 있다. 따라서 CFT기둥의 장점인 내력 및 시공성을 살리고, 현장 충전 공법에서의 단점을 극복하기 위하여 CFT부재의 PC화가 연구되어 왔다. 그러나 CFT부재의 PC화는 고중량물이기 때문에 운반과 양중능력의 확보 등 다른 문제를 낳게된다. 본 연구에서는 현장타설 CFT기둥의 단점과 공장생산 CFT기둥의 단점을 보완하기 위하여 새로운 형태인 중공 CFT 구조를 제안하고 중심축하중 하의 이력특성에 대한 기본적인 연구를 수행하였다. 이를 위하여 설정된 주된 실험변수는 CFT기둥의 충전율과 충전재의 강도이며, 특히 충전율은 0%, 30%, 50%, 80%, 100%를 설정하였다. 얻어진 결과는 기본적으로 항복강도레벨에 이르기까지 선형적인 거동을 나타내고 있으며, 내부 충전율이 증가함에 따라 강도, 강성 및 변형능력이 크게 나타나고 있다.

• 터널과지하공간
• /
• 제22권5호
• /
• pp.339-345
• /
• 2012

동적하중 하에서 암석의 변형거동 및 파괴강도는 발파, 지진 또는 암반돌출의 지진동에 의한 지하구조물의 안정해석에 중요하다. 본 연구에서는 스플릿 홉킨슨 압력봉(SHPB) 충격실험시스템을 석회암시료의 일축압축시험과 압열인장시험에 적용하여 고변형률과 동적강도 평가를 수행하였다. 충격봉의 발사속도를 제어하여 파괴강도 이하 동적응력 상태에서의 석회암시료의 동적응력-변형거동을 분석하였다. 시료 내 파괴여부 및 파괴양상을 파악하기 위하여 Micro-focus X-ray 단층촬영을 수행하였다. 동적 압축강도 실험결과, 석회암시료의 동적압축강도는 변형율속도 의존성을 보였으며, 동적 압축파괴강도는 140 MPa 이상으로 평가되었다. 동적 압열 인장 실험결과, 석회암시료의 동적 압열인장강도는 21 MPa 이상으로 정적 압열인장강도보다 3배 이상 높은 것으로 평가되었다.

• 콘크리트학회논문집
• /
• 제11권6호
• /
• pp.101-112
• /
• 1999

Structural walls have been mostly used for the design of reinforced concrete buildings in seismic areas because they play a role as an efficient bracing system and offer great potential for lateral load resistance and drift control. The lateral resistance system for the earthquake load should be designed to have enough ductility and stable hysteretic response in the critical regions where plastic deformation occurred beyond yielding. The behavior of the reinforced concrete element to experience large deformation in the critical areas by a major earthquake is affected by the performance of the confined core concrete. Thus, the confinement of concrete by suitable arrangements of transverse reinforcement results in a significant increase in both the strength and ductility of compressed concrete. This paper reports the experimental results of reinforced concrete structural walls for wall-type apartment structure under axial loads and cyclic reversal of lateral loads with different confinement of the boundary elements. The results show that confinement of the boundary element by open 'U'-bar and cross tie is effective. The shear strength capacity is not increased by the confinement but deformation capacity is improve.

• 한국농공학회논문집
• /
• 제57권2호
• /
• pp.57-66
• /
• 2015

The purpose of this study was to improved the durability of a improved movable weir by replacing the improved movable weir's metal gate with a hybrid steel/glass fiber reinforced polymer composites panel gate. Because the metal gate of a improved movable weir is always in contact with water, its service life is shortened by corrosion. This study made four type of hybrid steel/glass fiber reinforced polymer composites panel gate with different steel gate surface deformation (control, sand blast, scratch and hole), flexural. Fracture properties tests were performed depending on the steel gate surface deformation. According to the test results, the flexural behavior, flexural strength and fracture properties of hybrid steel/glass fiber reinforced polymer composites panel gate was affected by the steel panel gate surface deformation. Also, the sand blast type hybrid steel/glass fiber reinforced polymer composites panel gate shows vastly superior flexural and fracture performance compared to other types.

• Steel and Composite Structures
• /
• 제16권4호
• /
• pp.357-374
• /
• 2014

The design basis is being shifted from strength to deformation in modern performance-based design codes. This paper presents a practical method for optimization of eccentrically braced steel frames, based on the concept of uniform deformation theory (UDT). This is done by gradually shifting inefficient material from strong parts of the structure to the weak areas until a state of uniform deformation is achieved. In the first part of this paper, UDT is implemented on 3, 5 and 10 story eccentrically braced frames (EBF) subjected to 12 earthquake records representing the design spectrum of ASCE/SEI 7-10. Subsequently, the optimum strength-distribution patterns corresponding to these excitations are determined, and compared with four other loading patterns. Since the optimized frames have uniform distribution of deformation, they undergo less damage in comparison with code-based designed structures while having minimum structural weight. For further investigation, the 10 story EBF is redesigned using four different loading patterns and subjected to 12 earthquake excitations. Then a comparison is made between link rotations of each model and those belonging to the optimized one which revealed that the optimized EBF behaves generally better than those designed by other loading patterns. Finally, efficiency of each loading pattern is evaluated and the best one is determined.

• Journal of Welding and Joining
• /
• 제31권6호
• /
• pp.44-49
• /
• 2013

The influence of thermo-mechanical cycling on the microstructure and strength in the weld coarse-grained heat affected zone (CGHAZ) of Ti-Nb added low carbon HSLA steel was explored through Vickers hardness tests, nanoindentation experiments, scanning electron microscopy (SEM) and transmission electron microscopy (TEM) analysis. Undeformed and deformed CGHAZs were simulated using Gleeble simulator with different heat inputs of 30kJ/cm and 300kJ/cm. At high heat input of 300kJ/cm, the CGHAZ consisted of ferrite and pearlite and then their grain sizes were not affected by deformation. At low heat input of 30kJ/cm, the CGHAZ consisted of lath martensite and then the sizes of prior austenite grain, packet and lath width decreased with deformation. In addition, the fraction of particle increased with deformation and this is because the precipitation kinetics was accelerated by deformation. Meanwhile, the Vickers and nanoindentation hardness of deformed CGHAZ with 30kJ/cm heat input were higher than those of undeformed CGHAZ, which are due to the effect of grain refinement and precipitation strengthening.

• 열처리공학회지
• /
• 제3권2호
• /
• pp.20-31
• /
• 1990

This investigation has been carried out to make clear the effect of deformation temperature, strain rate and grain size on the tensile properties of 304L stainless steel. Tensile properties of the metastable austenitic 304L steel remarkably influenced by deformation temperature. Tensile strength increased with decreasing deformation temperature and the elongation showed maximum value near $40^{\circ}C$. In order to obtain the high elongation, a large amount of deformation is available in austenite before martensitic transformation and the martensite has to be induced gradually. Tensile strength and elongation increased with decreasing grain size. The temperature representing the maximum elongation shifted to low temperature and the peak width of elongation became broaden with decreasing austenite grain size. The volume fraction of strain induced martensite decreased with decreasing austenite grain size. As the strain rate increase, the temperature representing the maximum elongation value shifted to high temperature and volume fraction of strain induced martensite decreased.

• International Journal of Korean Welding Society
• /
• 제3권2호
• /
• pp.7-14
• /
• 2003

During the manufacture of a ship, longitudinal deformation is produced by fillet welding on the Built­Up beam used to improve the longitudinal strength of a ship. This deformation needs a correcting process separate from a manufacture process and decreases productivity and quality. This deformation is caused by welding moment, which is the value multiplied the shrinking force due to welding by the distance from the neutral axis on a cross section of Built­Up beam. This deformation can be offset by generating a moment which is the same magnitude with and is located in an opposite direction to the welding moment on web plate by induction heating. Accordingly, this study clarifies the creation mechanism of the longitudinal deformation on Built­Up beam with FEM analysis and presents the preventative method of this deformation by induction heating basing the mechanism and verifies its validity through analysis and experiments. The induction heating used here is performed by deciding its location and quantity with experiments and simple equations and by applying them to a real structure.