• Proceedings of the Korea Concrete Institute Conference
• /
• 1997.04a
• /
• pp.460-467
• /
• 1997

Compared to normal-strength concrete, high-strength concrete has the lower lateral expansion capacity caused by the higher elastic modulus and the lower internal crack characteristic. Therefore, the effect of the lateral confining action of hoops appears slowly and also in inefficient Nevertheless. it has been reported that the strength and deformation capacity of high-strength concrete is improved by well-distributed hoops. Due to that argument, this investigation has been compared and analyzed by the experimental works on the deformation capacity and the confinement mechanism of high-strength concrete shear wall of the high-rise building reinforced by rectangular steel tubes and rectangular hoops at both edges of the shear wall.

• Proceedings of the Korean Institute of Building Construction Conference
• /
• 2015.05a
• /
• pp.80-81
• /
• 2015

Thermal deformation behavior of high-strength concrete (HSC) exposed to fire is different from that of normal strength concrete (NSC). In case of ultra-high-strength concrete (UHSC), it is well known that thermal deformation behavior is greater than HSC. With increasing research of UHSC in buildings, it is necessary to understand the performance of UHSC at elevated temperatures considering loading condition. Therefore, evaluation on properties of thermal strain behavior properties of ultra high strength concrete by loading and high temperature was conducted.

• Journal of the Korean Society for Heat Treatment
• /
• v.7 no.2
• /
• pp.88-95
• /
• 1994

In order to compare mechanical properties of ausformed martensite with those of marformed martemsite in Fe-30%Ni-0.1%C alloy and to investigate their strengthening mechanisms, ausformed martensite and marformed martensite were prepared by ausforming treatment and marforming treatment respectively. The microstructures were observed and the quantities of retained austenite, hardness, yield strength, ultimate tensile strength and elongation were examined. The strength of ausformed martensite was mainly increased because of the lattice defects inherited from austenite. The ductility of ausformed martensite was constant at the rate of 7-8% by ductile matrix formation of the retained austenite in spite of the increase in strength. The strength of marformed martensite was increased by the increment in dislocation density, the crossing of transformation twin with deformation twin and the mutual crossing of deformation twin. The ductility of mar formed martensite was slightly lower than that of ausformed martensite, but the strength of mar formed martensite was prominently higher.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 2003.05a
• /
• pp.49-52
• /
• 2003

The effects of nitrogen on the deformation behavior of duplex stainless steel have been studied The variation of strength was correlated with the characteristic microstructures. Analysis based on Hall-Petch relation confirmed that nitrogen enhances phase-boundary strengthening effect. The evolution of dislocation structure, slip traces, and misorientation distribution during deformation were also characterized to elucidate the effect of nitrogen on inelastic deformation mechanism.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 1999.03b
• /
• pp.180-183
• /
• 1999

It is well known that Fe3Al intermetallic compound shows an anomalous peak of the yield strength at about 50$0^{\circ}C$ and then decrease at higher temperatures The dislocation structure was examined by transmission electron microscopy and high temperatures. The dislocation structure was examined by transmission electron microscopy and high temperature mechanical properties were examined by tensile and load relaxation tests. The flow stress curves obtained from load relaxation tests were then analyzed in terms of internal variable deformation theory. it was found that the flow curves consisted of three micro-deformation mechanisms -i. e inelastic deformation mode plastic deformation mode and dislocation creep deformation mode depending on both dislocation structure and deformation temperature. The flow curves could be well described by the constitutive equations of these three micro-deformation mechanisms based on the internal variable deformation theory.

• Transactions of Materials Processing
• /
• v.7 no.1
• /
• pp.23-35
• /
• 1998

In order to analyze the tensile deformation characteristics of laser welded tailored blanks. laser welded blanks of different thikness and strength combinations were prepared and tensile tests were done. The tensile elongation along the direction perpendicular to weld line of laser welded blanks was reduced as increasing the deformation restraining force (strength X thicknes) ratio between two welded sheets and fracture occurred at weaker side of base sheets if void ration of welded sheets and fracture occurred at weaker side of base sheets if void ratio of weld section was less than 45% The tensile elongation along weld line reached above 90% of the elongation of base material if welding was done perfectly. Total elongation along the direction perpendicular to weld line was able to be predicted by force equilibrium and power law behavior of base sheets and it was related with the deformation of stronger sheet and formability of weaker side.

• Computers and Concrete
• /
• v.17 no.2
• /
• pp.157-172
• /
• 2016

This paper presents a Strut-and-Tie Model for reinforced concrete (RC) columns subject to lateral loading. The proposed model is based on the loading path for the post-yield state, and the geometries of struts and tie are determined by the stress field of post-yield state. The analysis procedure of the Strut-and-Tie Model is that 1) the shear force and displacement at the initial yield state are calculated and 2) the relationship between the additional shear force and the deformation is determined by modifying the geometry of the longitudinal strut until the ultimate limit state. To validate the developed model, the ultimate strength and associated deformation obtained by experimental results are compared with the values predicted by the model. Good agreements between the proposed model and the experimental data are observed.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 2004.10a
• /
• pp.260-263
• /
• 2004

Since Outerrace is one of the components of driving shaft for power train of automobile and transmits high torque, high strength and high toughness are necessary so forging process is adopted to manufacture such parts. Therefore, in order to improve strength and toughness, heat treatment is accomplished after plastic deformation(forging). Because Each component of driving shaft is mounted to automobile after a series of forging, machining and heat treatment, in order to evaluate mechanical properties of such components in use, plastic deformation and heat treatment must be considered. So, in this paper, tensile tests are performed with tensile specimens which have passed through a series of upsetting, machining and heat treatment to evaluate mechanical properties of such components.

• Journal of the Korean Society for Heat Treatment
• /
• v.6 no.1
• /
• pp.26-36
• /
• 1993

In this study, the ausformed martensite and marformed martensite obtained from austenite with various deformation degrees in Fe-31% Ni-0.2%C alloy were transformed to revesed austenite at $510^{\circ}C$ by cyclic reverse martensite transformation. The effect of prior deformation, the rapid heating rate of reversion and number of cyclic transformation on the microstructure, mechanical properties of reversed austenite were investigated. The reverse austenite transformation is accomplised by the mechanism of shear type transformation. The structure of reversed austenite formed from ausformed martensite and marformed martensite with high deformation degrees is a fine structure of nearly equiaed grain containg a high density of dislocation tangles and was largely affected by the prior deformation applied before reversal transformation. The strength of reversed austenite is more increased with of cyclic transformation especially it is strength at the first cyclic transformation. The yield stress of revesed austenite of ausformed martensite is lower than that of marformed martensite.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 2003.10a
• /
• pp.269-273
• /
• 2003

There is a growing interest to replace the commercial steels with non-heat treated steels, which does not involve the spheroidization and quenching-tempering treatment. However, Non-heat treated steels should satisfy high strength and good formability without performing heat treatment. Therefore, it is important to investigate optimum materials showing a good combination of strength and formability after the drawing process. In this study, Dual-Phase Steels were studied as candidate materials for non-heat treated steels, which have different martensite morphologies and volume fractions obtained through heat-treatment of intercritical quenching (IcQ), intermediate quenching (ImQ) and step quenching (SQ). The mechanical properties of DP steels were measured by tension and compression tests. Also, the cold formability of three DP steels which have similar tensile strength value was investigated by estimating the deformation resistance and the forming limit. The deformation resistance which is important factor in determining die life was estimated by calculating the deformation energy. And the forming limit was estimated by measuring the critical strain revealing crack initiation at the notch tip of the specimens.