• 건축역사연구
• /
• 제7권4호
• /
• pp.9-27
• /
• 1998

The urban form of Korean cities significantly changed in the late Chosun dynasty. The influence of commercial development was the main cause of these changes. Commerce became a important function of existing cities, and the new type of commercial towns emerged at the important spots of traffic routes. In both cases streets became dominant element of urban form. Mainly commercial buildings aggregated along the streets, and to obtain higher land use intensity shape of lots became narrow and deep. Koyang(高陽) shows the most significant example of this new type of lot and lot pattern. Approximately 30 narrow and deep type of lots lined on each side of street forming about 390 meters long linear commercial town. Similar examples were found at the outside of south gate of Suwon(水原), Nuwon(樓院), and Pangyo(板橋).

• 한국농촌건축학회논문집
• /
• 제22권2호
• /
• pp.1-8
• /
• 2020

This study is intended to derive the adaptive reuse techniques through the history and aspects of new construction, extension, repair, and other works, limited to the deep and narrow lots facing Seongan-gil and Nammun-gil in Nammun-ro 2 ga of Cheongju, the historic urban area. The results are as follows. 1) In the case of newly built reinforced concrete buildings, the central part of the top floor of the residence or all floors are opened to the open space(void) to facilitate lighting and ventilation. This is developed as a convection phenomenon due to the temperature difference from the slits between buildings, which affects the entire air flow of the block. 2) The buildings of extension and repair are composed of two-story masonry or steel frame, both the front store facing the road and the house on the back, but it looks like one because it is in contact with each other. If only a small gap between the front and rear buildings is restored to an external space or a space equipped with sun light, a small breath can be provided in lighting and ventilation. 3) The existing two-story wooden stores and houses have lost their external space due to repairs. With minimal intervention to restore the small courtyard, slits, and space under the eaves, it will not only improve lighting and ventilation, but also create a unique appearance as a segment of the elongated store.

• 대한의용생체공학회:의공학회지
• /
• 제41권2호
• /
• pp.107-119
• /
• 2020

The deep neural networks (DNN) that can replicate the behavior of the human expert who recognizes the characteristics of ECG waveform have been developed and studied to analyze ECG. However, although the existing DNNs can not provide the explanations for their decisions, those trials have attempted to determine whether patients have certain diseases or not and those decisions could not be accepted because of the absence of relating theoretical basis. In addition, these DNNs required a lot of training data to obtain sufficient accuracy in spite of the difficulty in the acquisition of relating clinical data. In this study, a small-sized continuous data processing DNN (C-DNN) was suggested to determine the simple characteristics of ECG wave that were not required additional explanations about its decisions and the C-DNN can be easily trained with small training data. Although it can analyze small input data that was selected in narrow region on whole ECG, it can continuously scan all ECG data and find important points such as start and end points of P, QRS and T waves within a short time. The star and end points of ECG waves determined by the C-DNNs were compared with the results performed by human experts to estimate the accuracies of the C-DNNs. The C-DNN has 150 inputs, 51 outputs, two hidden layers and one output layer. To find the start and end points, two C-DNNs were trained through deep learning technology and applied to a parameter acquisition algorithms. 12 lead ECG data measured in four patients and obtained through PhysioNet was processed to make training data by human experts. The accuracy of the C-DNNs were evaluated with extra data that were not used at deep learning by comparing the results between C-DNNs and human experts. The averages of the time differences between the C-DNNs and experts were 0.1 msec and 13.5 msec respectively and those standard deviations were 17.6 msec and 15.7 msec. The final step combining the results of C-DNN through the waveforms of 12 leads was successfully determined all 33 waves without error that the time differences of human experts decision were over 20 msec. The reliable decision of the ECG wave's start and end points benefits the acquisition of accurate ECG parameters such as the wave lengths, amplitudes and intervals of P, QRS and T waves.

• Journal of Welding and Joining
• /
• 제30권4호
• /
• pp.24-30
• /
• 2012

Laser welding by fiber laser accompanied by a lot of spatter and humping bead. This is because the deep and narrow keyhole usually form due to high beam quality. So the weld bead is formed defects, because the plasma jet with a high vapor pressure make the molten pool on keyhole wall scattered. For such a reason, unstable behavior of keyhole is difficult to monitor laser welding by using the laser induced plasma. Mostly, fiber laser welding of thick plates most be influenced by this effect. Therefore, fiber laser welding has been difficult to apply the sole. Thus, laser welding monitoring based on plasma measurements have much difficulty in measurements and analysis of signal. In this study, influence of the plasma emission signal according to welding speed and laser power in fiber laser welding analysed by using RMS and FFT analysis. We can verify that RMS value of the plasma emission signal changes with welding parameters in fiber laser welding, and aspect ratio greater than 1, the peak of FFT frequency had been moved in accordance with welding parameter.

• 실천공학교육논문지
• /
• 제15권1호
• /
• pp.119-126
• /
• 2023

오늘날 자동차의 연비 향상 과 동적 거동 향상을 위해서 자동차 부품의 경량화 및 간소화 시대가 형성되고 있다. 설계와 제작의 간소화를 위해 제품 형상을 다양한 부품의 일체화로 진행되고 있다. 예를 들어 3개의 제품을 1개의 제품화 시키기 위해서 아주 협소한 부분까지 제품 가공하는 일이 발생되고 있다. 기존의 부품의 경우 가공의 편의성을 위해 정밀 다이캐스팅 또는 주물 생산으로 가공 후 조립하는데 다중 조립체(multi-piece) 방식은 공정수가 많이 필요로 하며, 부품의 정밀도와 강도를 저하시키는 요인이 된다. 가공 공정을 단순화 시키고 부품의 강도를 확보하기 위해서 일체형으로 제작하는 것이 단점을 극복하는데 매우 유리하지만 깊고 좁은 포켓 부분을 가공 할 경우 장비 자체 스핀들로는 가공이 불가능하다. 문제점을 해결하고자 절삭가공에 대한 연구가 활발하게 진행되고 있으며, 다축 복합가공 기술은 이러한 문제점을 해결할 뿐만 아니라, 지금까지 하나의 공작기계로 여러 공정에 따른 유연한 절삭가공이 어려웠던 복합 형상에도 절삭가공이 가능하다는 등 많은 장점을 가지고 있다. 하지만 고가의 장비로 인하여 제조경비 상승과 기계를 운영할 수 있는 기술자가 부족한 것이 현실이다. 5축 절삭 가공기에서는 깊고 협소한 구간의 제품을 생산할 때 공구의 간접으로 제품 생산에 사이클 타임이 늘어남은 물론 가공상에 문제점들이 많이 발생된다. 따라서 전용 공작기계 및 다축 복합가공기를 사용해야 한다. 그 대안으로 3축 머시닝센터에서 5축 이상의 다축 복합가공을 할 수 있는 특수 공구로서의 앵글 스핀들(angle spinde)이 사용될 수 있다. 앵글 스핀들 사용함으로 가공 진동 흡수, 낮은 열 발생과 작동 안정성, 우수한 치수 안정성, 강도 확보와 같은 분야에서 다양하고 지속적인 연구가 필요하다.